RKC4.4T-0.6-RSC4.4T/TEL is a TURCK extension cable with a straight M12 female connector on one end and a straight M12 male connector on the other (4-pin).

• Connectors: M12 x 1 female, straight, A-coded / M12 x 1 male, straight, A-coded; 4-pin, gold-plated brass (CuZn) contacts
• Cable: 0.6 m, PVC, black, Ø 4.6 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 250 V, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nuts, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -40...+105°C fixed, -5...+80°C mobile

The PVC jacket resists chemicals, oils, acids, alkaline solutions, microbes and hydrolysis, is flame retardant and free from LABS. Approval: cULus.

SOKTL150R4 is a foldable stand for Banner TL50 tower lights. It locks upright or folds down to 90°: loosen the control screw three turns, fold, then tighten the screw again.

• Material: black polycarbonate
• Base: Ø90 mm, 4 mounting holes Ø5.5 mm
• Tower light connection: M30 × 1.5 thread
• Included: mounting hardware

Once folded, the cable can be fixed in the groove on the unit with a cable tie.

M12EQ8 is the emitter of a Banner M12 series opposed-mode photo sensor pair, in a 12 mm nickel-plated brass barrel. Its visible red 660 nm beam reaches an M12 series receiver up to 5 m away; the emitter itself has no output.

• Sensing range: 5 m with an M12 series receiver
• Output: none (emitter)
• Supply: 10-30 V DC
• Housing: M12 threaded barrel, nickel-plated brass, PMMA lens, encapsulated
• Environment: IP67, IP68, NEMA 4X, -20...+60 °C
• Connection: integral M12 male connector, 4-pin

Needs an M12 series receiver, ordered separately. CE approved.

M18TIP8 is a Banner M18T series non-contact infrared temperature sensor with a 8:1 distance-to-spot ratio and a integrated lens. A thermopile detector measures the infrared energy an object emits and gives a 4-20 mA output proportional to its temperature, plus a PNP alarm.

• Accuracy: linearity ±2 °C at 0...+50 °C, ±1 °C or ±1 % above +50 °C; repeatability ±1 % or ±1 °C, whichever is greater
• Measuring range: -20...+300 °C; spectral range 8-14 µm; D:S 8:1; minimum taught span 10 °C
• Outputs: analog 4-20 mA, slope set by teach order; PNP alarm; response 75 ms (95 % step)
• Supply: 12-30 V DC, < 35 mA
• Protection: output short circuit
• Housing: M18 threaded barrel, 304 stainless steel, encapsulated
• Environment: IP67, -20...+70 °C; 5 min warm-up
• Connection: 2 m shielded PVC cable, 5 wires

The measuring window is taught with the push button or by remote teach, without potentiometers, and the target does not need to move. Linearity is specified for 0...+300 °C.

UL, CE and UKCA approved.

LX12R is the receiver of a Banner LX series part-sensing light curtain with a 295 mm sensing array. Its outputs switch while any part, down to 9.5 mm diameter, passes anywhere through the web of beams from the matching emitter.

• Sensing range: 300 mm to 2 m (reduced range 150-600 mm)
• Minimum object: 9.5 mm diameter
• Output: bipolar, 1 PNP and 1 NPN, 125 mA each; response 3.2 ms ON, 8.5 ms OFF
• Supply: 10-30 V DC, < 1 W
• Housing: aluminium, die-cast zinc end caps, acrylic window
• Environment: IP65, -20...+70 °C
• Connection: 2 m PVC cable, 5 wires

Emitter and receiver need no synchronisation wire. The off-time includes a 5 ms pulse stretcher, so short parts still give a readable output pulse. Not for personnel protection. Best resolution is within the centre 80 % of the sensing range.

LX12E is the emitter of a Banner LX series part-sensing light curtain with a 295 mm sensing array. It sends a strobed web of modulated beams to the matching LX receiver for detecting small or flat parts passing anywhere through the screen.

• Sensing range: 300 mm to 2 m with the matching receiver
• Output: none (emitter)
• Supply: 10-30 V DC, < 1 W
• Housing: aluminium, die-cast zinc end caps, acrylic window
• Environment: IP65, -20...+70 °C
• Connection: 2 m PVC cable, 5 wires

Needs the LX receiver of the same array length, ordered separately; no synchronisation wire is needed. Green LED shows power, red LED reduced range or a fault. Not for personnel protection. Best resolution is within the centre 80 % of the sensing range.

The isPro USBv4 is the successor of isPro USBx12. It is compatible with the isPro USBx12. This interface is optionally available with an isFF/PA MAU media access converter, with which it can be connected to a PROFIBUS DP and PROFIBUS PA network.

CL50GRYAPQ is a Banner CL50 series 50 mm LED column light with green, red and yellow segments and an audible alarm. Each colour is switched by its own PNP input, one colour at a time.

• Colours: green 525 nm (72 lm), red 625 nm (38 lm), yellow 590 nm (30 lm)
• Audible: continuous tone, 2.7 kHz, up to 92 dB at 1 m, adjustable down to 62 dB
• Inputs: PNP, one per colour, response 10 ms
• Supply: 18-30 V DC, up to 100 mA per colour, alarm 25 mA
• Housing: Ø50 x 145.3 mm, ABS/polycarbonate, black, M30x1.5 base mount
• Environment: IP50, -20...+50 °C
• Connection: integral M12 male connector, 5-pin

The light connects through a separately ordered 5-pin M12 female cordset. UL and CE approved.

WL50SWSSL11Q is a Banner WL50S series 50 mm LED spot light with an ±11° lens, in a 316 stainless steel housing sealed with Viton for washdown and chemical cleaning. Three high-intensity LEDs give 1365 lx at 1 m.

• Light: white 5000-8300 K, 285 lm; 5460 lx at 0.5 m, 1365 lx at 1 m
• Supply: 12-30 V DC, 400 mA max
• Housing: Ø56 x 71.1 mm, 316 stainless steel, polycarbonate window, M30x1.5 base mount, FDA-grade silicone gasket
• Environment: IP67, IP69K, -20...+50 °C
• Connection: integral M12 male connector, 5-pin; only 2 wires used

The light connects with a 4-pin or 5-pin M12 female cordset, ordered separately. LED service life 50,000 h. UL, CE and UKCA approved.

QS18VN6LLPQ8 is a Banner QS18 series polarised retroreflective photo sensor with a Class 1 visible red laser, working from 0.1 to 10 m to a reflector. The narrow laser beam detects small objects and gaps, and the polarising filter stops shiny objects acting as a reflector.

• Sensing range: 0.1-10 m with a reflector
• Output: complementary NPN, Light Operate and Dark Operate
• Response: 0.7 ms; repeatability 130 µs
• Supply: 10-30 V DC
• Housing: rectangular with M18 threaded nose, ABS, acrylic lens
• Environment: IP67, NEMA 4X, -10...+50 °C
• Connection: integral M12 male connector, 4-pin

Needs a reflector, ordered separately. Sensitivity is set with a potentiometer. UL and CE approved.

AFI4-5D30.4006.1300 is a Baumer CombiLyz inductive conductivity sensor with display and bottom process connection. It passes conductivity and temperature on as two separate 4...20 mA signals, and over IO-Link 1.1 the same readings and the sensor settings are also available digitally.

• Measuring range: 14 selectable ranges, 0...500 µS/cm to 0...1000 mS/cm; temperature -20...150 °C
• Output: 2 x 4...20 mA (conductivity, temperature), 2 solid-state relays, IO-Link 1.1
• Supply: 15...35 V DC (18...30 V DC with IO-Link)
• Housing: FlexHousing Ø80 mm, AISI 304, G 1 A hygienic connection, PEEK Natura probe L=60 mm
• Environment: IP67 / IP69K; process -20...140 °C (up to 150 °C for less than 1 h), up to 25 bar
• Connection: 1 x M12-A, 5-pin + 1 x M12-A, 8-pin, stainless steel AISI 304

Used for concentration control of CIP solutions and for phase separation between product, water and cleaning solution in dairy, brewery and beverage lines. The minimum measurable conductivity is 50 µS/cm, so the sensor does not suit demineralised or purified water.

cULus listed (E491206); wetted parts in PEEK Natura comply with FDA 21 CFR 177.2415.

TL50BGYRALSQ is a Banner TL50 series 50 mm LED tower light with 4 colour segments: blue, green, yellow, red, from the bottom up, topped by a sealed audible alarm. Each colour has its own input wire and the inputs are bimodal, so the tower can be driven from either PNP or NPN controller outputs.

• Colours: blue 470 nm, green 528 nm, yellow 590 nm, red 625 nm
• Audible: continuous tone, 2.9 kHz, up to 94 dB at 1 m, adjustable down to 74 dB
• Inputs: bimodal (PNP or NPN), one per colour, response 10 ms
• Supply: 18-30 V DC or 24 V AC 50/60 Hz, up to 45 mA per colour, alarm 35 mA
• Housing: Ø50 x 264.6 mm, ABS base and covers, polycarbonate light segments, black, M30x1.5 base mount
• Environment: IP67, -20...+50 °C
• Connection: integral M12 male connector, 8-pin

The tower connects through a separately ordered 8-pin M12 female cordset. Audible intensity is adjusted by rotating the front cover of the alarm.

Vibration tested to IEC 60068-2-6, shock to IEC 60068-2-27 (30 g, 11 ms).

WKC4.5T-1-RSC4.5T/TXL is a TURCK extension cable with an angled M12 female connector on one end and a straight M12 male connector on the other (5-pin).

• Connectors: M12 x 1 female, angled / M12 x 1 male, straight; A-coded, 5-pin, gold-plated brass (CuZn) contacts
• Cable: 1 m, PUR, black, Ø 4.8 mm, 5 x 0.34 mm², core colours BN, WH, BU, BK, GY
• Ratings: 4 A, 60 V, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nuts, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 5 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The PUR jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.

S4BR30-1200-S is the receiver of a Banner EZ-SCREEN S4B Type 4 safety light curtain with a 1200 mm defined area and 30 mm resolution (hand detection). When any beam is interrupted, both OSSD safety outputs switch off; the lighted end cap shows clear, weak beam, blocked beam or fault from a distance.

• Defined area: 1200 mm; resolution 30 mm; response time 15.0 ms
• Operating range: 0.1...12 m
• Outputs: two redundant PNP OSSD safety outputs, 24 V DC, max 0.5 A each; configurable pin for weak beam output or IO-Link (COM2)
• Supply: +24 V DC ±15 %, 96 mA typical without load
• Housing: anodised aluminium, 38 x 40 mm, glass-filled polycarbonate end caps
• Environment: IP65, -20...+55 °C, indoor use
• Connection: RD (removable disconnect) socket; 5-pin or 8-pin RD cordset with M12 ordered separately

With the 8-pin RD cordset the receiver monitors the contactors itself (EDM) and needs no external safety module; with the 5-pin cordset it is wired to a safety relay, safety controller or safety PLC. Reduced resolution can be switched on to ignore one blocked beam, and up to four pairs can be cascaded. Models longer than 900 mm need an additional side mount bracket.

Type 4 per IEC 61496-1 and -2, Category 4 PL e per EN ISO 13849-1, SIL3 per IEC 61508. MTTFd 287 years, PFHd 3.08 × 10⁻⁹ (single pair).

S4BE30-1200-S is the emitter of a Banner EZ-SCREEN S4B Type 4 safety light curtain with a 1200 mm defined area and 30 mm resolution (hand detection). It projects a row of synchronised, modulated infrared beams (860 nm) from end to end of the housing, so there is no dead zone at either end.

• Defined area: 1200 mm; resolution 30 mm; system response time 15.0 ms
• Operating range: 0.1...12 m
• Indicators: bi-colour status indicator, two tri-colour scan code indicators
• Supply: +24 V DC ±15 %, 33 mA typical
• Housing: anodised aluminium, 38 x 40 mm, glass-filled polycarbonate end caps
• Environment: IP65, -20...+55 °C, indoor use
• Connection: RD (removable disconnect) socket; RD cordset with M12 ordered separately

The emitter works only as a pair with an S4B receiver of the same length and resolution. The scan code (1 or 2) is set with switches in the RD cordset, so that two pairs mounted close to each other do not interfere. Models longer than 900 mm need an additional side mount bracket.

Type 4 per IEC 61496-1 and -2, Category 4 PL e per EN ISO 13849-1, SIL3 per IEC 61508. MTTFd 287 years, PFHd 3.08 × 10⁻⁹ (single pair).

Q20PFF150 is a Banner Q20 series fixed-field photo sensor with a 150 mm cutoff and a small visible red 655 nm spot. It detects objects closer than the cutoff and ignores the background beyond it.

• Sensing range: 150 mm cutoff, fixed
• Output: complementary PNP, Light Operate and Dark Operate
• Response: 0.8 ms; repeatability 155 µs
• Supply: 10-30 V DC
• Housing: compact rectangular, thermoplastic, acrylic lens
• Environment: IP67, NEMA 4X, -20...+60 °C
• Connection: 2 m PVC cable, 4 wires

There is no sensitivity adjustment; the cutoff is set at the factory.

UL and CE approved.

- Working temperature: 0 to 70 °C

PSD-24-4 is a Banner desktop power supply that converts mains voltage to 24 V DC on an M12 connector cable. The input cord has a US-style plug.

• Input: 90-264 V AC, 47-63 Hz
• Output: 24 V DC ±5 %, 3.9 A, 96 W; short-circuit protected
• Output connector: M12 (pin 1 V+, pin 3 V-)
• Housing: 140 x 60 x 34 mm
• Environment: IP20, 0...+40 °C, not for wet areas

UL 1310 Class 2; emissions FCC, CISPR 22 and VCCI Class B.

S15LGYPQ is a Banner S15L series two-color status indicator that screws in between a sensor and its cordset. Green is on while the sensor has power, and yellow replaces it when the sensor's PNP output is active.

• Colors: green - power, yellow - sensor output active
• Input: PNP, pin 4 (black wire)
• Supply: 10...30 V DC, up to 15 mA
• Housing: Ø15 × 57.8 mm, nickel-plated brass coupling, translucent white PVC
• Environment: IP65, IP67, IP68, -40...+40 °C
• Connection: integral 4-pin M12 male and female

The indicator is fitted where the sensor's own LEDs cannot be seen, for example inside a machine or behind a guard. All four pins pass straight through from male to female, so an IO-Link sensor can also be connected through it. The input responds to PNP signals only.

Meets CE, UKCA and UL/CSA requirements, enclosure rating UL Type 1.

SA-FFB12 is a Banner foldable base for ½" stand-off pipes. The pipe can be tilted through 110°, so a raised light can be folded down for service or for clearance.

• Fits: ½" NPSM/DN15 stand-off pipes
• Movement: 110° rotation
• Material: black polycarbonate, stainless steel hardware

TL50BGYRQ is a Banner TL50 series 50 mm LED tower light with 4 colour segments: blue, green, yellow, red, from the bottom up. Each colour has its own input wire and the inputs are bimodal, so the tower can be driven from either PNP or NPN controller outputs.

• Colours: blue 465 nm, green 525 nm, yellow 590 nm, red 625 nm
• Inputs: bimodal (PNP or NPN), one per colour, response 10 ms
• Supply: 18-30 V DC, up to 26 mA per colour
• Housing: Ø50 x 219.1 mm, polycarbonate housing, black, M30x1.5 base mount
• Environment: IP67, -40...+50 °C
• Connection: integral M12 male connector, 5-pin

The tower connects through a separately ordered 5-pin M12 female cordset.

Vibration tested to IEC 60068-2-6, shock to IEC 60068-2-27 (30 g, 11 ms).

RSIO-L5-6SI2SO-C is a Banner RSio remote safety I/O block that brings six safety inputs and two OSSD outputs onto a CIP Safety over EtherNet/IP network. Each input port also accepts an In-Series Diagnostics (ISD) chain of up to 32 devices, 192 per block.

• Inputs and outputs: 6 safety input ports, single or dual channel; 2 OSSD outputs, 1 A at 24 V DC, splittable; up to 12 PNP non-safe outputs
• Communication: CIP Safety over EtherNet/IP, 10/100 Mbit/s, two M12 D-coded 4-pin Ethernet ports
• Configuration: IP address on 3 rotary dials; set up from the safety PLC project, Studio 5000 recommended
• Supply: 24 V DC ±20 %, 200 mA without load; 5-pin L-coded M12 power in and pass-through out, 8 A per circuit
• Housing: glass-filled polyamide, epoxy-encapsulated, 261.9 x 73.9 x 39.4 mm; I/O on M12 A-coded 5-pin
• Environment: IP65, IP67, -25...+70 °C, indoor use only

The block needs a safety PLC with CIP Safety on EtherNet/IP; Banner provides the EDS file and Studio 5000 AOI and UDT files. Input reaction time is 6 ms plus debounce (default 6 ms), output reaction time 5 ms.

Up to Category 4 and PL e (EN ISO 13849-1), SIL 3 (IEC 61508); EMC per IEC 61326-3-1. CE and UL.

RSIO-MA4-6SI2SO-C is a Banner RSio remote safety I/O block that brings six safety inputs and two OSSD outputs onto a CIP Safety over EtherNet/IP network. Each input port also accepts an In-Series Diagnostics (ISD) chain of up to 32 devices, 192 per block.

• Inputs and outputs: 6 safety input ports, single or dual channel; 2 OSSD outputs, 1 A at 24 V DC, splittable; up to 12 PNP non-safe outputs
• Communication: CIP Safety over EtherNet/IP, 10/100 Mbit/s, two M12 D-coded 4-pin Ethernet ports
• Configuration: IP address on 3 rotary dials; set up from the safety PLC project, Studio 5000 recommended
• Supply: 24 V DC ±20 %, 200 mA without load; 4-pin 7/8" Mini power in and pass-through out, 8 A per circuit
• Housing: glass-filled polyamide, epoxy-encapsulated, 261.9 x 73.9 x 39.4 mm; I/O on M12 A-coded 5-pin
• Environment: IP65, IP67, -25...+70 °C, indoor use only

The block needs a safety PLC with CIP Safety on EtherNet/IP; Banner provides the EDS file and Studio 5000 AOI and UDT files. Input reaction time is 6 ms plus debounce (default 6 ms), output reaction time 5 ms.

Up to Category 4 and PL e (EN ISO 13849-1), SIL 3 (IEC 61508); EMC per IEC 61326-3-1. CE and UL.

PKG3M-2-RSC4T/TEL is a TURCK adapter cable with a straight M8 female connector on one end and a straight M12 male connector on the other (3-pin).

• Connectors: M8 x 1 female, straight / M12 x 1 male, straight, A-coded; 3-pin, gold-plated brass (CuZn) contacts
• Cable: 2 m, PVC, black, Ø 4.3 mm, 3 x 0.34 mm², core colours BN, BU, BK
• Ratings: 4 A, 50 V AC/60 V DC, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nuts, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -40...+105°C fixed, -5...+80°C mobile

The PVC jacket resists chemicals, oils, acids, alkaline solutions, microbes and hydrolysis, is flame retardant and free from LABS. Approval: cULus.

SMBLXR is a back-mount bracket that holds the device securely at one end.

• Mounting: back mount, at one end
• Material: zinc-plated cold-rolled steel
• Holes: Ø2.6 mm (A and B)

TL50RALSQ is a Banner TL50 series 50 mm LED tower light with 1 colour segment: red, from the bottom up, topped by a sealed audible alarm. Each colour has its own input wire and the inputs are bimodal, so the tower can be driven from either PNP or NPN controller outputs.

• Colours: red 625 nm
• Audible: continuous tone, 2.9 kHz, up to 94 dB at 1 m, adjustable down to 74 dB
• Inputs: bimodal (PNP or NPN), one per colour, response 10 ms
• Supply: 18-30 V DC or 24 V AC 50/60 Hz, up to 45 mA per colour, alarm 35 mA
• Housing: Ø50 x 142.5 mm, ABS base and covers, polycarbonate light segments, black, M30x1.5 base mount
• Environment: IP67, -20...+50 °C
• Connection: integral M12 male connector, 4-pin

The tower connects through a separately ordered 4-pin M12 female cordset. Audible intensity is adjusted by rotating the front cover of the alarm.

Vibration tested to IEC 60068-2-6, shock to IEC 60068-2-27 (30 g, 11 ms).

IM12-DI03-1S-2T-S/24VDC/CC is a 1-channel TURCK isolating switching amplifier in a 12.5 mm housing with two potential-free transistor outputs up to 10 kHz. The second output works either as a copy of the signal or as an alarm output for input faults.

• Channels: 1 input for NAMUR sensors (EN 60947-5-6) or potential-free contacts
• Outputs: 2 potential-free, short-circuit-proof transistors, ≤30 V DC, 0.1 A, ≤10 kHz
• Supply: 10...30 V DC, ≤1.03 W typical dissipation
• Housing: polycarbonate/ABS, 120 x 12.5 x 128 mm, DIN rail (NS35)
• Connection: removable spring-type terminals, 0.2...2.5 mm²
• Environment: IP20, -25...+70 °C

DIP switches on the front set the output mode, input circuit monitoring and the operating mode. An input fault makes the red LED flash according to NE44 and blocks the transistor of that channel. Mechanical contacts need either monitoring switched off or the resistor wiring shown in the datasheet.

Approvals: ATEX, cULus; for use in ATEX Zone 2. Usable in safety circuits up to SIL 2 (IEC 61508).

PSGS4M-4422-5M is a TURCK Industrial Ethernet cable with a straight M8 male connector (4-pin) on one end and open cores on the other. The 4-wire CAT 5e cable (AWG 22) is PNO compliant for PROFINET.

• Connector: M8 x 1, male, straight, 4-pin, gold-plated contacts
• Cable: 5 m, PUR, green, Ø 6.5 mm, 4 x 0.32 mm², core colours WH, YE, BU, OG
• Shield: aluminium foil and tinned copper wire
• Ratings: 4 A, 30 V; impedance 100 Ω, capacitance 50 pF/m
• Housing: TPU (UL 94), nickel-plated coupling nut
• Environment: IP67 (only when screwed in); -40...+80°C fixed, -30...+80°C mobile
• Drag chain: at least 5 million bending cycles, bending radius ≥15 x Ø, torsion ±180°/m

The green PUR jacket is halogen free (IEC 60754), oil resistant (IEC 60811-2-1, UL 13) and flame retardant (IEC 60332-1-2, UL FT2, UN/ECE R118); RoHS compliant. Approval: UL Listed.

T18-2VPDL-2M is a Banner T18-2 series diffuse sensor with visible red light that detects objects by the light they reflect back. The right-angle 18 mm threaded housing has epoxy-encapsulated electronics and food-grade plastics, for wet and washdown areas. A single-turn potentiometer sets the sensitivity.

• Sensing range: 750 mm
• Output: complementary PNP (NO and NC), 100 mA total up to +55 °C; response 1.5 ms ON / 0.75 ms OFF
• Supply: 10-30 V DC (10-24 V DC above +55 °C), < 16 mA
• Housing: right-angle, 18 mm thread, PBT polyester, PMMA window
• Environment: IP67, IP68, IP69K, -40...+70 °C; ECOLAB chemical compatibility
• Connection: 2 m PVC cable

Vibration per MIL-STD-202G method 201A, shock per method 213B (75 g operating).

SME312LPQD is a Banner MINI-BEAM Expert polarized retroreflective photo sensor with a visible red 650 nm beam and a range of 10 mm to 3 m. The polarizing filter rejects reflections from shiny objects, so only light returned by the reflector is seen.

• Sensing: polarized retroreflective, 10 mm...3 m with reflector, red 650 nm
• Outputs: bipolar, 1x PNP and 1x NPN, 150 mA each (100 mA at 70 °C); response 500 µs, repeatability 100 µs
• Supply: 10-30VDC, below 45 mA
• Housing: MINI-BEAM, reinforced thermoplastic polyester, encapsulated, M18x1 nose thread with nut
• Environment: IP67, -20...+70 °C
• Connection: integral M12 5-pin connector

Set with the push button or the gray remote TEACH wire: the first condition taught becomes Output ON, so Light or Dark Operate is not selected separately. The green indicator flashes when the signal approaches the switching threshold.

Q45BB6DLQ5 is a Banner Q45 series long-range diffuse photo sensor with an infrared beam, in a rugged rectangular housing. It detects objects by the light they reflect back, up to 1.8 m from the sensor.

• Sensing range: 1.8 m, adjustable
• Output: bipolar, 1 PNP and 1 NPN, Light or Dark Operate by switch
• Response: 2 ms; repeatability 500 µs
• Supply: 10-30 V DC
• Housing: rugged rectangular, thermoplastic, acrylic lens, 30 mm threaded mounting hub
• Environment: IP67, NEMA 4X, -40...+70 °C
• Connection: integral M12 male connector, 4-pin

Sensitivity is set with a multi-turn control. CE approved.

DQ12RB6R is the receiver of a Banner DQ12 series miniature opposed-mode photo sensor pair. It switches when an object breaks the beam from a DQ12 emitter up to 3 m away, with one PNP and one NPN output.

• Sensing range: 3 m with a DQ12 emitter
• Output: bipolar, 1 PNP and 1 NPN, Dark Operate
• Response: 1.3 ms ON, 0.7 ms OFF; repeatability 125 µs
• Supply: 10-30 V DC
• Housing: miniature rectangular, polyamide, polycarbonate lens
• Environment: IP67, -20...+55 °C
• Connection: 2 m PVC cable, 4 wires

Needs a DQ12 emitter, ordered separately. Dark Operate means the outputs switch on when the beam is blocked.

UL, CE and UKCA approved.

DQ126E is the emitter of a Banner DQ12 series miniature opposed-mode photo sensor pair. Its visible red 645 nm beam reaches a DQ12 receiver up to 3 m away; the emitter itself has no output.

• Sensing range: 3 m with a DQ12 receiver
• Output: none (emitter)
• Supply: 10-30 V DC
• Housing: miniature rectangular, polyamide, polycarbonate lens
• Environment: IP67, -20...+55 °C
• Connection: 2 m PVC cable, 2 wires

Needs a DQ12 receiver, ordered separately. The visible red beam makes the pair easy to align by eye.

UL, CE and UKCA approved.

S100PTVD2WAD2Q is a Banner S100 Pro series touch operator display that combines status indication, text and operator input in a single M30 threaded housing. This version works without an industrial network: the PLC switches states through discrete inputs, while text, colours and animations are loaded into the unit beforehand with Banner Pro Editor.

• Display: two-row white dot-matrix display, 13 characters per line, 16 RGB LED ring and audible alert
• Control: 5 capacitive touch zones with vibration feedback, response time max. 300 ms
• Control signals: discrete inputs, output max. 150 mA
• Supply: 12-30 V DC
• Housing: black polycarbonate with tinted window, Ø100 mm, M30x1.5 threaded base, IP66/IP69K, -40...+50°C
• Connection: integral M12 male connector, 5-pin

The display mounts in a Ø30 mm hole at the machine station - pick-to-light positions, takt timer, counter and step confirmation. The configuration is loaded with Pro Editor before installation, so changing text or colours means disconnecting the unit and connecting it to a PC.

CE marked, compliant with FCC Part 15 Class B and ICES-003(B), housing rated UL Type 4X.

FW-M12KU5W-G-ZF-ME-SH-9 is a field-wireable M12 female connector for PROFIBUS-DP. It is assembled on site onto a cut length of bus cable, so a damaged connector or an awkward cable run can be repaired without replacing a whole cordset. The cable screen is picked up by an iris spring and carried through to the metal housing.

• Connector: M12 × 1 female, straight, B-coded, 5-pin, gold-plated CuZn contacts
• Bus: PROFIBUS-DP up to 12 Mbit/s, overall shield connected via iris spring
• Rating: 4 A, 125 V, contact resistance ≤ 5 mΩ, over 100 mating cycles
• Termination: screw/clamp connection for 0.37...0.75 mm² cores, cable diameter 7...9 mm
• Housing: nickel-plated die-cast zinc with M18 × 1 screw-in thread, FPM/FKM seal
• IP67 when screwed together, −40 °C to +85 °C

It is used to terminate PROFIBUS-DP segments at drives, remote I/O and field devices, and for repairs in cabinets and on machines where a pre-moulded cordset cannot be routed. No crimping tool is needed — the cores are clamped and the gland is tightened by hand.

S100PTVD2WAKQ is a Banner S100 Pro series touch operator display that combines status indication, text and operator input in a single M30 threaded housing. Over IO-Link the controller changes text, colours and the state of each touch zone at runtime, so one unit serves several machine modes without reconfiguration.

• Display: two-row white dot-matrix display, 13 characters per line, 16 RGB LED ring and audible alert
• Control: 5 capacitive touch zones with vibration feedback, response time max. 300 ms
• Communication: IO-Link
• Supply: 18-30 V DC, 280 mA at 18 V DC, 210 mA at 24 V DC
• Housing: black polycarbonate with tinted window, Ø100 mm, M30x1.5 threaded base, IP66/IP69K, -40...+50°C
• Connection: integral M12 male connector, 4-pin

The display mounts in a Ø30 mm hole at the machine station - pick-to-light positions, takt timer, counter and step confirmation. Note that this version starts at 18 V DC, not 12 V DC as the other S100 Pro versions.

CE marked, compliant with FCC Part 15 Class B and ICES-003(B), housing rated UL Type 4X.

S100PTVD2WASQ is a Banner S100 Pro series touch operator display that combines status indication, text and operator input in a single M30 threaded housing. The controller changes text, colours and the meaning of each touch zone at runtime over Modbus RTU, so one unit serves several machine modes without reconfiguration.

• Display: two-row white dot-matrix display, 13 characters per line, 16 RGB LED ring and audible alert
• Control: 5 capacitive touch zones with vibration feedback, response time max. 300 ms
• Communication: Modbus RTU over RS-485, 9600, 19200 and 38400 bit/s
• Supply: 12-30 V DC, 415 mA at 12 V DC, 210 mA at 24 V DC
• Housing: black polycarbonate with tinted window, Ø100 mm, M30x1.5 threaded base, IP66/IP69K, -40...+50°C
• Connection: integral M12 male connector, 4-pin

The display mounts in a Ø30 mm hole at the machine station - pick-to-light positions, takt timer, counter and step confirmation. Prepared modes run without programming, while Modbus registers let the PLC drive each row, colour and the audible alert separately.

CE marked, compliant with FCC Part 15 Class B and ICES-003(B), housing rated UL Type 4X.

RSr-L-SIL-8A-Q is a remote safety relay from Banner's RSr family. It converts the OSSD outputs of a safety device into two volt-free normally open relay contacts, so a light curtain, a safety I/O block or a safety PLC can switch loads that do not tolerate OSSD test pulses. This is the latch model: after a stop the outputs stay off until a reset signal is applied on the A-code port.

• Input: one dual-channel OSSD pair, ON threshold > 15 V DC, OFF below 5 V DC
• Output: two normally open safety contacts, 8 A at 24 V DC (DC1) per IEC/EN 60947-5-1
• Supply: 24 V DC ±20 %, under 100 mA, approximately 2 W
• Response time 20 ms maximum, minimum OFF-state recovery 400 ms
• Housing: thermoplastic polyurethane, IP65 / IP67, 138 × 50 × 27.8 mm, −25 °C to +60 °C
• Connection: four 5-pin M12 connectors — two A-code for signals and reset, two L-code for the switched power

The relay mounts directly on the machine with two M4 screws or a bracket, so distributed safety outputs can switch motors, valves and brakes without a control cabinet. There are no DIP switches and nothing to program. Four LED indicators show status, fault, both safety inputs and the relay output.

SIL 3 per IEC 61508 and EN 62061, Category 4 / PL e per EN ISO 13849-1; CE marked and UL listed.

RSr-L-SIT-8A-Q is a remote safety relay from Banner's RSr family. It converts the OSSD outputs of a safety device into two volt-free normally open relay contacts, so a light curtain, a safety I/O block or a safety PLC can switch loads that do not tolerate OSSD test pulses. This is the trip model: the contacts follow the safety inputs directly, and pin 5 of the A-code port carries an auxiliary output that mirrors the relay state.

• Input: one dual-channel OSSD pair, ON threshold > 15 V DC, OFF below 5 V DC
• Output: two normally open safety contacts, 8 A at 24 V DC (DC1) per IEC/EN 60947-5-1, plus a 24 V DC 70 mA solid-state AUX output
• Supply: 24 V DC ±20 %, under 100 mA, approximately 2 W
• Response time 20 ms maximum, minimum OFF-state recovery 400 ms
• Housing: thermoplastic polyurethane, IP65 / IP67, 138 × 50 × 27.8 mm, −25 °C to +60 °C
• Connection: four 5-pin M12 connectors — two A-code for signals and the AUX output, two L-code for the switched power

The relay mounts directly on the machine with two M4 screws or a bracket, so distributed safety outputs can switch motors, valves and brakes without a control cabinet. There are no DIP switches and nothing to program. Four LED indicators show status, fault, both safety inputs and the relay output.

SIL 3 per IEC 61508 and EN 62061, Category 4 / PL e per EN ISO 13849-1; CE marked and UL listed.

LMB1822FM is an aluminium adapter for mounting the Banner S18L indicator, which has an M18 × 1 thread, in a standard 22 mm hole.

• Fits: M18 × 1 thread into a 22 mm hole (22 × 1.5 mm)
• Material: aluminium, black
• Mounting: flush
• Included: adapter, nut, gasket

Q20PLV is a Banner Q20 series non-polarised retroreflective photo sensor with a visible red 645 nm beam and a range of 6 m to a reflector. It switches when an object breaks the beam between the sensor and the reflector.

• Sensing range: 6 m with a reflector
• Output: complementary PNP, Light Operate and Dark Operate
• Response: 0.8 ms; repeatability 155 µs
• Supply: 10-30 V DC
• Housing: compact rectangular, thermoplastic, acrylic lens
• Environment: IP67, NEMA 6, -20...+60 °C
• Connection: 2 m PVC cable, 4 wires

Needs a reflector, ordered separately. Being non-polarised, it can be fooled by shiny targets; sensitivity is set with a potentiometer.

UL and CE approved.

R58ECRGB2Q is a Banner R58E Expert registration mark sensor with a red, green and blue LED light source. During TEACH it picks the colour that gives the most contrast between the mark and its background and detects 16 levels of grey scale; the switching frequency is 10 kHz.

• Sensing: fixed focus 10 mm ±3 mm, image 1.2 x 3.8 mm, perpendicular to sensor length
• Light source: red 636 nm, green 525 nm, blue 472 nm, selected automatically during TEACH
• Outputs: bipolar, 1x PNP and 1x NPN, 100 mA each; response 50 µs, repeatability 15 µs
• Supply: 10-30VDC, max 75 mA at 10 VDC
• Housing: zinc alloy die-cast, acrylic lens
• Environment: IP67, -10...+55 °C
• Connection: 150 mm PVC pigtail with M12 5-pin connector

Static and Dynamic TEACH by push button or the gray remote wire; in Dynamic TEACH the shorter event becomes Output ON, so Light/Dark Operate is set automatically. Mount at about 15° to shiny surfaces. A 30 ms OFF-delay or ON-delay can be enabled.

Vibration and shock per IEC 60068-2-6 and IEC 60068-2-27.

K50LGRASYPQ is a Banner K50L series 50 mm dome indicator with green, red and yellow light and a sealed audible alarm, in an encapsulated polycarbonate housing for washdown areas. Each colour and the alarm have their own PNP input.

• Colours: green, red, yellow, one colour on at a time
• Audible: continuous tone, 2.9 kHz, 65 dB at 1 m, fixed
• Inputs: PNP; indicator response 1 ms, audible 10 ms
• Supply: 12-30 V DC, up to 35 mA per colour at 30 V, alarm 35 mA
• Housing: Ø50 x 73 mm, polycarbonate, encapsulated, M30x1.5 base mount
• Environment: IP67, IP69K, NEMA 4X, -20...+50 °C
• Connection: integral M12 male connector, 5-pin

The 65 dB alarm is fixed in level; the indicator connects through a separately ordered 5-pin M12 female cordset.

Vibration tested to MIL-STD-202F, method 201A; shock to IEC 60947-5-2 (30 g, 11 ms). UL and CE approved.

QS18VN6W is a Banner QS18 series divergent diffuse photo sensor with a wide infrared beam and a 100 mm range. The wide beam picks up small or irregular objects at close range without precise aiming.

• Sensing range: 100 mm
• Output: complementary NPN, Light Operate and Dark Operate
• Response: 0.6 ms; repeatability 150 µs
• Supply: 10-30 V DC
• Housing: rectangular with M18 threaded nose, ABS, acrylic lens
• Environment: IP67, NEMA 4X, -20...+70 °C
• Connection: 2 m PVC cable, 4 wires

There is no sensitivity adjustment. UL and CE approved.

T30R-1515-KUQ is a Banner T30R series 122 GHz FMCW radar sensor with a 15 x 15° beam, measuring distance from 0.2 to 15 m. Radar is unaffected by dust, rain, fog or wind and detects targets regardless of colour.

• Accuracy: linearity < ±20 mm below 500 mm, < ±4 mm above 500 mm (1 m² RCS target); repeatability < 1 mm
• Measuring range: 0.2-15 m; detection from 0.15 m
• Outputs: white wire analog 0-10 V or 0.5-4.5 V; black wire IO-Link or push/pull, PNP or NPN, 50 mA; response 2 ms analog, 6 ms discrete
• Supply: 12-30 V DC, < 100 mA at 24 V
• Protection: reverse polarity, transient overvoltage, output short circuit
• Housing: M30 threaded barrel, PBT, COP window, max. torque 2.3 Nm
• Environment: IP67, -40...+65 °C
• Connection: integral M12 male connector, 5-pin

The analog window and switch points are taught with the push buttons or remote teach, or set over IO-Link or with Banner Measurement Sensor Software via a USB adapter.

Radio approvals ETSI EN 305 550 and FCC Part 15. Vibration tested to MIL-STD-202F, method 201A; shock to method 213B (75 g). UL, CE and UKCA approved.

CMVT-QR20-IOLX3-H1141 is a condition monitoring vibration and temperature sensor measuring acceleration and velocity over three axes plus the housing temperature. It is intended for rotating machine parts where rising vibration indicates bearing wear, imbalance or shaft misalignment, so the deviation is caught before a failure.

• Measuring range: acceleration 16 g RMS (6.6 kHz sampling), velocity 0...320 mm/s RMS @ 78 Hz, temperature -40...+85°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: velocity linearity deviation ≤ ±1 % @ 78 Hz, acceleration ≤ ±3 % @ 78 Hz; repeatability ≤ ±5 % @ 78 Hz
• Outputs: pin 4 - IO-Link or SIO, pin 2 - SIO; two PNP/NPN switching outputs in SIO mode; IO-Link COM 3 (230.4 kBaud)
• Supply: 18...30 VDC (IO-Link), 10...30 VDC (SIO), consumption < 50 mA
• Protection: against wire break and reverse polarity
• Housing: rectangular QR20, Ultem plastic, 71.6 x 62.6 x 20 mm
• Environment: IP68/IP69K, pollution degree 3, shock 200 g (4 ms), vibration 20 g
• Connection: M12 x 1 male connector, 4-pin

Over IO-Link the output quantity is selectable - acceleration or velocity, RMS or peak-to-peak - and the switching thresholds are set there. Thresholds can be parameterised to the ISO 10816-3 machine classes or defined freely. A green LED shows the supply and, when flashing, active IO-Link communication; two yellow LEDs show an exceeded threshold.

UL registration number E351232. MTTF 548 years to SN 29500 (Ed. 99) at 40°C. Shock tested to EN 60068-2-27, vibration to EN 60068-2-6, temperature cycling to EN 60068-2-14 (20 cycles).

CMVT-QR20-IOLX3-H1141/3GD is a condition monitoring vibration and temperature sensor measuring acceleration and velocity over three axes plus the housing temperature. It is the ATEX version of the CMVT-QR20 for zones 2 and 22 - the measuring side is unchanged, but the device carries an Ex marking and a narrower permitted ambient range.

• Measuring range: acceleration 16 g RMS (6.6 kHz sampling), velocity 0...320 mm/s RMS @ 78 Hz, temperature -40...+85°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: velocity linearity deviation ≤ ±1 % @ 78 Hz, acceleration ≤ ±3 % @ 78 Hz; repeatability ≤ ±5 % @ 78 Hz
• Outputs: pin 4 - IO-Link or SIO, pin 2 - SIO; two PNP/NPN switching outputs in SIO mode; IO-Link COM 3 (230.4 kBaud)
• Supply: 18...30 VDC (IO-Link), 10...30 VDC (SIO), consumption < 50 mA
• Protection: against wire break and reverse polarity
• Housing: rectangular QR20, Ultem plastic, 71.6 x 62.6 x 20 mm
• Environment: IP68/IP69K, pollution degree 3, shock 200 g (4 ms), vibration 20 g; permitted ambient in the ATEX zone -30...+70°C
• Connection: M12 x 1 male connector, 4-pin

Device marking: Ex II 3 G Ex ec IIC T4 Gc / II 3 D Ex tc. The plug connection must not be disconnected under voltage, and the sensor must be protected against mechanical damage.

Over IO-Link the output quantity is selectable - acceleration or velocity, RMS or peak-to-peak - and the switching thresholds are set there. Thresholds can be parameterised to the ISO 10816-3 machine classes or defined freely. A green LED shows the supply and, when flashing, active IO-Link communication; two yellow LEDs show an exceeded threshold.

UL registration number E351232. MTTF 548 years to SN 29500 (Ed. 99) at 40°C. Shock tested to EN 60068-2-27, vibration to EN 60068-2-6, temperature cycling to EN 60068-2-14 (20 cycles).

CMVT-M8TA1X-LI2IOL-H1141 is a stainless steel vibration and temperature sensor with an M8 screw-in thread, measuring over one axis at a 23.6 kHz sampling rate. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: acceleration 10 g RMS / 14 g peak, velocity 0...128 mm/s RMS @ 159 Hz, temperature -40...+80°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: ≤ ±0.5 % @ 159 Hz; temperature linearity deviation ≤ 10 %
• Outputs: pin 4 - IO-Link or SIO, pin 2 - 4...20 mA or SIO; IO-Link COM 2 (38.4 kBaud)
• Supply: 18...30 VDC, consumption < 120 mA in IO-Link mode
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms), vibration 20 g
• Connection: M12 x 1 connector, 4-pin

Frequency ranges and switching thresholds are configurable over IO-Link, so only the band in which a given machine's fault appears has to be watched. The 4...20 mA output on pin 2 carries the same quantity in analogue form, so the sensor connects to a controller with no IO-Link master.

MTTF 164 years to SN 29500 (Ed. 99). Shock tested to EN 60068-2-27, vibration to EN 60068-2-6.

CMVT-M8TE1X-LI2IOL-H1141 is a stainless steel vibration and temperature sensor with an M8 screw-in thread and a 64 kHz sampling rate. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: acceleration 33.9 g RMS / 48 g peak (10 Hz...10 kHz), velocity 0...256 mm/s RMS @ 159 Hz, temperature -40...+80°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: ≤ ±0.5 % @ 159 Hz; temperature linearity deviation ≤ 10 %
• Outputs: pin 4 - IO-Link or SIO, pin 2 - 4...20 mA or SIO; IO-Link COM 3 (230.4 kBaud)
• Supply: 18...30 VDC, consumption < 120 mA in IO-Link mode
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms)
• Connection: M12 x 1 connector, 4-pin

Besides the aggregated RMS values the sensor outputs a bearing condition indicator and transfers the raw signal over IO-Link BLOB at up to 64 kHz with a low-pass filter at 12 kHz. FFT analysis can therefore be done off the sensor - on the controller or a server. Frequency ranges and thresholds are configurable over IO-Link.

MTTF 112 years to SN 29500 (Ed. 99) at 40°C. Shock tested to EN 60068-2-27.

CMVT-M8TA1X-LI220-H1141 is a stainless steel vibration sensor with an M8 screw-in thread that measures the velocity RMS value over one axis and outputs it as a 4...20 mA signal, where 20 mA corresponds to 20 mm/s RMS. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: velocity 0...20 mm/s RMS, one axis, 23.6 kHz sampling
• Accuracy: ≤ ±0.5 % @ 159 Hz
• Outputs: 4...20 mA, load resistance ≤ 0.5 kΩ
• Supply: 18...30 VDC, consumption < 100 mA
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms), vibration 20 g
• Connection: M12 x 1 connector, 4-pin

There is no IO-Link and nothing to configure - the sensor wires straight into a controller's analogue input, and the measuring span is fixed by the model chosen.

MTTF 164 years to SN 29500 (Ed. 99). Shock tested to EN 60068-2-27, vibration to EN 60068-2-6.

CMVT-M8TA1X-LI225-H1141 is a stainless steel vibration sensor with an M8 screw-in thread that measures the velocity RMS value over one axis and outputs it as a 4...20 mA signal, where 20 mA corresponds to 25 mm/s RMS. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: velocity 0...25 mm/s RMS, one axis, 23.6 kHz sampling
• Accuracy: ≤ ±0.5 % @ 159 Hz
• Outputs: 4...20 mA, load resistance ≤ 0.5 kΩ
• Supply: 18...30 VDC, consumption < 100 mA
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms), vibration 20 g
• Connection: M12 x 1 connector, 4-pin

There is no IO-Link and nothing to configure - the sensor wires straight into a controller's analogue input, and the measuring span is fixed by the model chosen.

MTTF 164 years to SN 29500 (Ed. 99). Shock tested to EN 60068-2-27, vibration to EN 60068-2-6.

CMTH-M12-IOL6X2-H1141 is a capacitive humidity and temperature sensor for condition monitoring. It is intended for machine parts where temperature or humidity affects machine availability or process quality, and suits both indoor and outdoor use.

• Accuracy: temperature ±0.8°C; humidity ±5 % RH (10...90 % RH), ±7 % RH (0...10 % and 90...100 % RH). When installed in metal, in an environment with convection
• Measuring range: temperature -40...+100°C, humidity 0...100 % RH, resolution 0.1 K and 0.1 % RH; humidity response time t63 6 s
• Outputs: output 1 - switching or IO-Link, output 2 - switching; IO-Link v1.1 COM 3, Class A, Smart Sensor Profile 4
• Supply: 18...30 VDC, DC 4-wire, consumption < 50 mA, rated current ≤ 150 mA
• Protection: against short circuit, wire break and reverse polarity
• Housing: chrome-plated CuZn metal, M12 x 1 thread, nut torque up to 10 Nm
• Environment: IP67, operating temperature -40...+100°C
• Connection: M12 x 1 connector, 4-pin, cable up to 20 m

Over IO-Link a temperature offset is configurable and switching thresholds or windows can be set for temperature and humidity. The sensor calculates the dew point, builds temperature and humidity histograms and counts operating hours and threshold transitions. A green LED shows the supply.

Meets CE and UL requirements. EMC to EN 61326-1, shock to IEC 60068-2-27 (50 g, 6 ms), vibration to IEC 60068-2-6 (10...150 Hz, 20 g). MTTF 610 years.

CMTH-M12-IOL6X2-H1141/3GD is a capacitive humidity and temperature sensor for condition monitoring in the ATEX version for zones 2 and 22. It is intended for machine parts where temperature or humidity affects machine availability or process quality, and suits both indoor and outdoor use.

• Accuracy: temperature ±0.8°C; humidity ±5 % RH (10...90 % RH), ±7 % RH (0...10 % and 90...100 % RH). When installed in metal, in an environment with convection
• Measuring range: temperature -40...+100°C, humidity 0...100 % RH, resolution 0.1 K and 0.1 % RH; humidity response time t63 6 s
• Outputs: output 1 - switching or IO-Link, output 2 - switching; IO-Link v1.1 COM 3, Class A, Smart Sensor Profile 4
• Supply: 18...30 VDC, DC 4-wire, consumption < 50 mA, rated current ≤ 150 mA
• Protection: against short circuit, wire break and reverse polarity
• Housing: chrome-plated CuZn metal, M12 x 1 thread, nut torque up to 10 Nm
• Environment: IP67, operating temperature -40...+100°C; ATEX category II 3 G (Ex zone 2) and II 3 D (Ex zone 22)
• Connection: M12 x 1 connector, 4-pin, cable up to 20 m

Over IO-Link a temperature offset is configurable and switching thresholds or windows can be set for temperature and humidity. The sensor calculates the dew point, builds temperature and humidity histograms and counts operating hours and threshold transitions. A green LED shows the supply.

Meets CE and UL requirements. EMC to EN 61326-1, shock to IEC 60068-2-27 (50 g, 6 ms), vibration to IEC 60068-2-6 (10...150 Hz, 20 g). MTTF 610 years.

CMTH-M12E-IOL6X2-H1141 is a capacitive humidity and temperature sensor for condition monitoring with an integrated heating function that stabilises the measurement. It is intended for machine parts where temperature or humidity affects machine availability or process quality, and suits both indoor and outdoor use.

• Accuracy: temperature ±0.5°C; humidity ±3.5 % RH (10...90 % RH), ±5 % RH (0...10 % and 90...100 % RH). When installed in metal, in an environment with convection
• Measuring range: temperature -40...+100°C, humidity 0...100 % RH, resolution 0.1 K and 0.1 % RH
• Outputs: output 1 - switching or IO-Link, output 2 - switching; IO-Link v1.1 COM 3, Class A, Smart Sensor Profile 4
• Supply: 18...30 VDC, DC 4-wire, consumption < 50 mA, rated current ≤ 150 mA
• Protection: against short circuit, wire break and reverse polarity
• Housing: chrome-plated CuZn metal, M12 x 1 thread, nut torque up to 10 Nm
• Environment: IP67, operating temperature -40...+100°C
• Connection: M12 x 1 connector, 4-pin, cable up to 20 m

Over IO-Link a temperature offset is configurable and switching thresholds or windows can be set for temperature and humidity. The sensor calculates the dew point, builds temperature and humidity histograms and counts operating hours and threshold transitions. A green LED shows the supply.

Meets CE and UL requirements. EMC to EN 61326-1, shock to IEC 60068-2-27 (50 g, 6 ms), vibration to IEC 60068-2-6 (10...150 Hz, 20 g). MTTF 610 years.

CMMT-QR20-IOL6X3-H1141 is a magnetic field sensor for condition monitoring that measures the field over three axes, calculates the sum vector and reads temperature as well. It is intended for positions where a change in the magnetic field reports on machine condition - the weakening of a permanent magnet, or the influence of a stray field.

• Measuring range: magnetic field -2500...+2500 µT, resolution 1 µT; temperature -25...+70°C, resolution 0.1 K
• Response time: at least 8 s
• Outputs: output 1 - PNP/NPN or IO-Link, output 2 - PNP/NPN; IO-Link COM 3 (230.4 kBaud), Smart Sensor Profile
• Supply: 18...30 VDC, no-load current 80 mA, rated current ≤ 250 mA
• Protection: against short circuit (cyclic), wire break and reverse polarity
• Housing: rectangular QR20, Ultem plastic, 71.6 x 62.6 x 20 mm
• Environment: IP68/IP69K, pollution degree 3, operating temperature -25...+70°C
• Connection: M12 x 1 male connector, 4-pin

Over IO-Link an offset and a limit value can be set per axis and assigned to a specific switching output, so which direction is changing can be separated out. A green LED shows the supply, two yellow LEDs the output states.

EMC to EN 61326-1.

MAGKIT-M8T is the magnetic mount for the CMVT-M8T family of vibration sensors. The sensor screws into the magnet's female thread, and the magnet is placed on the machine surface without drilling or cutting a thread in the equipment itself.

• Fits: CMVT-M8T family sensors with an M8 screw-in thread
• Thread: M8 x 12 mm, female
• Material: stainless steel V4A
• Holding force: 342 N at 28°C

The mount is intended for flexible, relocatable mounting. Permanent and operationally secure fixing depends on the conditions at the application and must be evaluated by the user.

MAGKIT-M5 is the magnetic mounting kit for CMVT-QR20 rectangular-housing sensors. The sensor is screwed to two magnets with the supplied M5 screws, and the magnets hold it on the machine surface without drilling a hole in the equipment.

• Fits: CMVT-QR20 and CMMT-QR20 family sensors
• Supplied: 2 mounting magnets, 2 washers, 2 M5 x 12 screws
• Dimensions: magnet Ø 32 x 7 mm, M5 female thread

Permanent and operationally secure fixing depends on the conditions at the application and must be evaluated by the user.

RKH4.4-10/TFE is a TURCK connection cable with a straight M12 female connector (4-pin) on one end and open cores on the other.

• Connector: M12 x 1 female, straight, 4-pin
• Cable: 10 m, PVC, grey, Ø 4.5 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 250 V
• Housing: grey PP, stainless steel (V4A) coupling nut, FPM/FKM seal
• Environment: IP65, IP67, IP68, IP69 (only when screwed in); -25...+80°C fixed, 0...+80°C mobile

Designed for food and beverage areas: grey PVC jacket (RAL 7040) resistant to acids, alkalis, oils and chemicals, flame retardant per DIN EN 60332, stainless steel coupling nut. RoHS and REACH compliant. Approvals: GOST, Ecolab.

S15LGYPM8Q4 is a Banner S15L series two-color status indicator that screws in between a sensor with an M8 connector and its cordset. Green is on while the sensor has power, and yellow replaces it when the sensor's PNP output is active.

• Colors: green - power, yellow - sensor output active
• Input: PNP
• Supply: 10...30 V DC, up to 15 mA
• Housing: Ø15 × 58 mm
• Environment: IP66, IP67, -40...+70 °C
• Connection: integral 4-pin M8 male and female

The indicator is fitted where the sensor's own LEDs cannot be seen, for example inside a machine or behind a guard. The input responds to PNP signals only.

BC-M12F4-M12M4-22-2 is a Banner double-ended M12 extension cordset with a straight 4-pin female connector at one end and a straight 4-pin male connector at the other. The cable is rated as UL ITC/PLTC tray cable, so it can be laid in cable trays without conduit where those approvals apply.

• Connectors: M12x1, female / male, straight, A-coded, 4-pin; length 2 m
• Cable: black PVC, 22 AWG, 4 conductors, Ø 5.33 mm, unshielded
• Ratings: 4 A, 30 V
• Body: TPU connector body, nickel-plated brass coupling nut
• Environment: IP66, IP67, IP68, -40...+105 °C

Wire colours: brown 1, white 2, blue 3, black 4; pin 5 not used. Bend radius at least 4x the cable diameter fixed and 15x in motion; vibration per IEC 60068-2-6, shock per IEC 60068-2-27.

RKC8T-2-RSC8T/TXL is a TURCK extension cable with a straight M12 female connector on one end and a straight M12 male connector on the other (8-pin).

• Connectors: M12 x 1 female, straight, A-coded / M12 x 1 male, straight, A-coded; 8-pin, gold-plated brass (CuZn) contacts
• Cable: 2 m, PUR, black, Ø 5.8 mm, 8 x 0.25 mm², core colours BN, WH, BU, BK, GY, PK, VT, OG
• Ratings: 2 A, 30 V, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nuts, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 5 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The PUR jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.

T18-2VPFF200-Q8 is a Banner T18-2 series fixed-field sensor with a 200 mm cutoff that ignores objects and background beyond that distance. The right-angle 18 mm threaded housing has epoxy-encapsulated electronics and food-grade plastics, for wet and washdown areas.

• Sensing range: fixed cutoff 200 mm
• Output: complementary PNP (NO and NC), 100 mA total up to +55 °C; response 2 ms ON / 2 ms OFF
• Supply: 10-30 V DC (10-24 V DC above +55 °C), < 16 mA
• Housing: right-angle, 18 mm thread, PBT polyester, PMMA window
• Environment: IP67, IP68, IP69K, -40...+70 °C; ECOLAB chemical compatibility
• Connection: M12 male connector, 4-pin

Vibration per MIL-STD-202G method 201A, shock per method 213B (75 g operating).

MTL7787P+ is a two-channel Zener barrier from the Eaton Crouse-Hinds MTL7700 series for intrinsically safe analogue and digital signal loops. Both channels are positive polarity: channel 1 is rated 28 V / 234 Ω / 119 mA, channel 2 is a diode return channel.

• Channel 1: safety description 28 V, 234 Ω, 119 mA; max end-to-end resistance 253 Ω
• Channel 2: 28 V diode return, 0.9 V + 21 Ω
• Working voltage: 26.4 V at 10 µA; Vmax 27.2 V; fuse rating 80 mA
• Housing: polycarbonate, 12.6 x 90 x 105 mm, approx. 140 g
• Mounting: 35 mm DIN rail, earthed through the rail
• Environment: IP20, -20...+60 °C

Hazardous area ratings: IECEx/ATEX Zone 0 and Zone 2; NEC Class I, Division 2 and Class I, Zone 2.

QS18VP6AF300Q is a Banner QS18 series background suppression sensor that detects objects up to a cutoff distance set between 30 and 300 mm and ignores anything beyond it. The cutoff is set with a five-turn screw on the housing, without teach or software.

• Sensing range: cutoff adjustable 30...300 mm; minimum range 4...10 mm depending on cutoff
• Output: complementary PNP (NO and NC), 100 mA total; response 2.8 ms, repeatability 250 µs
• Supply: 10-30 V DC, < 16 mA
• Housing: QS18, 18 mm thread, ABS, acrylic lens; visible red LED, 640 nm
• Environment: IP67, NEMA 6, -20...+55 °C
• Connection: 150 mm cable with M8 4-pin male connector