LMB30RA is a Banner LMB series sealed right-angle bracket for indicators and sensors with a 30 mm threaded base. Gaskets and O-rings between the mounting surface, the base and the adapter give an IP67 installation, and the cable can be routed through the mounting surface.

• Included: base, 30 mm adapter, set screw, fasteners, O-rings and gaskets
• Device thread: M30 × 1.5
• Material: black polycarbonate
• Mounting: 3 × M5 screws (5.5 mm holes), 12.7 mm cable hole
• Protection rating: IP67 (assembled bracket)

The device is turned to the required orientation relative to the base and locked with the 8-32 set screw, tightened to 0.17 Nm max.

SMB30A is a Banner right-angle bracket for sensors with a 30 mm housing. The curved slot lets the sensor be turned before the screws are tightened.

• Sensor hole: Ø30.5 mm
• Mounting: M6 (¼") hardware, 40 mm hole centre spacing
• Material: 12-gauge stainless steel

SA-M30 is a Banner cover that hides the outer M30 thread on a light's base.

• Fits: devices with an M30 base, Banner lists TL70 tower lights and the K90 series
• Material: black polycarbonate
• Included: mounting hardware

SOP-E12-150A is a Banner 150 mm stand-off pipe for mounting an indicator, tower light or sensor elevated above the mounting surface.

• Length: 150 mm
• Thread: ½" NPT at both ends (NPSM/DN15)
• Material: black anodised aluminium

The lower end of the pipe needs a mounting base and the upper end an adapter for the device's base.

SA-F12-3 is a Banner elevated mount system base that fixes a ½" stand-off pipe to a flat surface with three screws.

• Connection: ½" NPSM/DN15 pipe
• Dimensions: Ø70 mm, 3 mounting holes
• Material: black polycarbonate
• Included: M4 mounting hardware and nitrile blend gasket

SA-M22E12 is a Banner adapter that connects a light's 22 mm base to a ½" stand-off pipe for elevated mounting. Banner specifies it for TL30 tower lights.

• Connection: 22 mm device base - ½" NPSM/DN15 pipe
• Material: black polycarbonate
• Mounting hardware: not included

SMBWLS28RA is a Banner replacement end bracket kit for WLS28 LED lights.

• Included: 2 end brackets and 4 screws
• Material: 1.8 mm (14-gauge) cold-rolled steel
• Finish: zinc plate with clear chromate

SA-E12M30 is a Banner elevated mount system base adapter that fixes a ½" stand-off pipe in a surface with a 30 mm hole and covers the pipe end.

• Connection: ½" NPSM/DN15 pipe
• Mounting: in a 30 mm (1-3/16") hole
• Material: black acetal
• Included: mounting hardware

PRO-KIT is a Banner kit for configuring Pro series lights and selected sensors from a PC with the Pro Editor software. It is needed for initial configuration only, not for the device's operation in the machine.

• Included: converter cable, splitter and power supply
• Software: Banner Pro Editor
• Fits: Banner Pro series lights and selected sensors

CE and UKCA compliant.

WC-K50C is a Banner silicone cover that protects K50 compact indicators and touch buttons in washdown areas.

• Fits: Banner K50 compact indicators and touch buttons
• Material: FDA-grade silicone
• Protection rating: IP67 and IP69K

SMB30SC is a Banner swivel bracket for sensors with a 30 mm housing. Once the orientation is set, the swivel is locked with the included screw.

• Sensor hole: Ø30.0 mm
• Mounting: Ø7.0 mm holes on a Ø50.8 mm circle
• Material: black reinforced thermoplastic polyester
• Included: stainless steel mounting and swivel locking hardware

SA-M30TE12 is a Banner tapered adapter that joins a light with a 30 mm base to the top of a ½" stand-off pipe and covers the joint. It is typically used with CL50 column lights, TL50 tower lights and K50 indicators.

• Connection: 30 mm light base to ½" NPSM/DN15 pipe
• Material: black acetal
• Included: mounting hardware

SOP-E12-150SS is a Banner 150 mm stand-off pipe in 304 stainless steel for mounting an indicator, tower light or sensor raised above the mounting surface.

• Length: 150 mm
• Thread: ½" NPT at both ends (NPSM/DN15 system)
• Material: 304 stainless steel

The lower end needs a mounting base and the upper end an adapter for the device base.

SMBAMS30RA is a Banner SMBAMS series right-angle bracket for sensors with a 30 mm housing. Its slots let the sensor be turned through more than 90°.

• Sensor hole: Ø31.0 mm
• Mounting: Ø6.5 mm hole and 26.8 × 7.0 mm slot
• Material: 2.6 mm (12-gauge) cold-rolled steel

SOK-TL50-150A is a complete Banner elevated mounting kit that raises a TL50 tower light 150 mm above the surface. The pipe passes through a 30 mm drilled hole and the adapter on top gives a tapered transition to the light base.

• Fits: Banner TL50 tower lights
• Included: SA-M30TE12 adapter, SOP-E12-150A pipe, SA-E12M30 base cover
• Pipe: 150 mm, black anodised aluminium, ½" NPT

SA-F12 is a Banner flange base that fixes a ½" stand-off pipe to a flat surface. It is die-cast zinc, painted black.

• Fits: ½" NPSM/DN15 stand-off pipes
• Material: die-cast zinc, black paint
• Included: M5 mounting hardware and nitrile gasket

SOP-E12-300SS is a Banner 300 mm stand-off pipe in 304 stainless steel for mounting an indicator, tower light or sensor raised above the mounting surface.

• Length: 300 mm
• Thread: ½" NPT at both ends (NPSM/DN15 system)
• Material: 304 stainless steel

The lower end needs a mounting base and the upper end an adapter for the device base.

LMBE12RA45 is a Banner right-angle bracket for mounting an indicator light on a stand-off pipe with a 1/2-14 NPSM nut. The centre of the nut sits 45 mm from the wall.

• Fits: stand-off pipe with 1/2-14 NPSM nut
• Offset: 45 mm from the mounting surface to the nut centre
• Mounting: 2x Ø11 mm holes, 35.0 mm hole centre spacing
• Material: zinc-plated steel

LMBLC25T is a Banner stainless steel clip bracket for LC25 lights. The light snaps into the clip, which is screwed to the surface through a clearance hole for M5 hardware.

• Fits: Banner LC25
• Material: stainless steel
• Mounting: Ø 5.2 mm clearance hole for M5 hardware
• Included: 1 clip bracket and 2 plastic spacers

LMBWLS15 is a set of Banner stainless steel clip brackets for WLS15 LED light strips. The strip snaps into the clips, which are screwed to the surface through clearance holes for M5 hardware.

• Fits: Banner WLS15
• Material: stainless steel
• Mounting: Ø 5.2 mm clearance hole for M5 hardware
• Included: 3 clip brackets and 2 plastic spacers

SOKTL150R4 is a foldable stand for Banner TL50 tower lights. It locks upright or folds down to 90°: loosen the control screw three turns, fold, then tighten the screw again.

• Material: black polycarbonate
• Base: Ø90 mm, 4 mounting holes Ø5.5 mm
• Tower light connection: M30 × 1.5 thread
• Included: mounting hardware

Once folded, the cable can be fixed in the groove on the unit with a cable tie.

SA-FFB12 is a Banner foldable base for ½" stand-off pipes. The pipe can be tilted through 110°, so a raised light can be folded down for service or for clearance.

• Fits: ½" NPSM/DN15 stand-off pipes
• Movement: 110° rotation
• Material: black polycarbonate, stainless steel hardware

LMB1822FM is an aluminium adapter for mounting the Banner S18L indicator, which has an M18 × 1 thread, in a standard 22 mm hole.

• Fits: M18 × 1 thread into a 22 mm hole (22 × 1.5 mm)
• Material: aluminium, black
• Mounting: flush
• Included: adapter, nut, gasket