EA5E600Q is the emitter of a Banner EZ-ARRAY measuring light curtain, with a 600 mm array of 120 infrared beams at 5 mm spacing. It is synchronised with the receiver over the cable, and all evaluation and outputs are in the receiver.

• Array: 600 mm, 120 beams, 5 mm spacing, infrared LED
• Range: 400 mm...4 m between emitter and receiver
• Supply: 12-30 V DC, 40 mA at 24 V
• Housing: clear-anodised aluminium, acrylic lens cover; end-cap brackets included
• Environment: IP65, -40...+70 °C
• Connection: M12, 8-pin; cordset ordered separately

It works with an EZ-ARRAY receiver of the same length, which sets the outputs and the Modbus interface.

EA5R600PIXMODQ is the receiver of a Banner EZ-ARRAY measuring light curtain with a 600 mm array of 120 beams at 5 mm spacing. The controller is built into the receiver: it evaluates the beam pattern and reports object position, height, width or count through two analog outputs, two discrete outputs and Modbus RTU.

• Resolution: 5 mm straight scan, 2.5 mm edge scan; minimum object 5 mm (low-contrast mode)
• Range: 400 mm...4 m between emitter and receiver
• Outputs: 2x analog 4-20 mA, 2x PNP 100 mA, Modbus RTU over RS485 (up to 15 nodes)
• Supply: 12-30 V DC, 60 mA at 24 V
• Housing: clear-anodised aluminium, acrylic lens cover; end-cap brackets included
• Environment: IP65, -40...+70 °C
• Connection: M12, 8-pin; cordset ordered separately

The receiver is configured with its six-position DIP switch or with the supplied PC software; a straight scan takes 2.8...26.5 ms depending on array length. It works with the EZ-ARRAY emitter of the same length, and each unit needs its own 8-pin M12 cordset.

LX3EQ is the emitter of the Banner LX series light curtain, with a 67 mm light screen for part sensing. Infrared LEDs are spaced at 9.5 mm and fire in sequence, so together with an LX receiver of the same length they form a crosshatched beam pattern that also detects thin and narrow objects. No synchronisation wire is needed between emitter and receiver.

• Distance between emitter and receiver: 0.3...2 m (Normal), 0.15...0.6 m (Reduced)
• Output: none, the unit is an emitter
• Supply: 10...30 V DC, less than 1 W
• Housing: aluminium profile, die-cast zinc endcaps, acrylic lens; overall length 113.4 mm
• Environment: IP65, -20...+70 °C
• Connection: 150 mm cable with an M12 5-pin male connector

The light curtain is used for part ejection verification and package detection on conveyors, where the object may cross the beam field at any point. The range is selected with the grey wire: 5...30 V DC gives Normal, 0...2 V DC gives Reduced range, and the emitter LED indicators show the selection. The green LED is on when power is applied and the emitter is good; the red LED is on in reduced range. The emitter must be paired with an LX receiver of the same length and range, and the device is not intended for personnel protection.

Meets CE and UKCA requirements; UL listing E71083, Class 2 power, UL Environmental Rating Type 1.

LX3RQ is the receiver of the Banner LX series light curtain, with a 67 mm light screen for part sensing. Photodiodes are spaced at 9.5 mm and recognise each emitter pulse separately, so the crosshatched beam pattern also detects thin objects such as a sheet of paper. In the standard range the smallest detectable object is 9.5 mm in diameter.

• Distance between emitter and receiver: 0.3...2 m (Normal), 0.15...0.6 m (Reduced)
• Output: bipolar, one PNP and one NPN output at the same time, 125 mA each, conducting while the beam is blocked
• Response time: 0.8 ms on, 6 ms off with a 5 ms pulse stretcher
• Supply: 10...30 V DC, less than 1 W
• Housing: aluminium profile, die-cast zinc endcaps, acrylic lens; overall length 113.4 mm
• Environment: IP65, -20...+70 °C
• Connection: 150 mm cable with an M12 5-pin male connector

The receiver is used for part ejection verification and package detection on conveyors, where the object may cross the beam field at any point. The range is selected with the grey wire: 5...30 V DC gives Normal, 0...2 V DC gives Reduced range. The amber LED shows a conducting output, the bicolour LED shows green in Normal and red in Reduced range, and a flashing red light indicates a receiver hardware fault. Resolution is best in the middle 80 % of the beam field, the receiver must be paired with an LX emitter of the same length and range, and the device is not intended for personnel protection.

Meets CE and UKCA requirements; UL listing E71083, Class 2 power, UL Environmental Rating Type 1.

EA5E450Q is the emitter of a Banner EZ-ARRAY measuring light curtain, with a 450 mm array of 90 infrared beams at 5 mm spacing. It is synchronised with the receiver over the cable, and all evaluation and outputs are in the receiver.

• Array: 450 mm, 90 beams, 5 mm spacing, infrared LED
• Range: 400 mm...4 m between emitter and receiver
• Supply: 12-30 V DC, 30 mA at 24 V
• Housing: clear-anodised aluminium, acrylic lens cover; end-cap brackets included
• Environment: IP65, -40...+70 °C
• Connection: M12, 8-pin; cordset ordered separately

It works with an EZ-ARRAY receiver of the same length, which sets the outputs and the Modbus interface.

S4BR30-300-S is the receiver of a Banner EZ-SCREEN S4B Type 4 safety light curtain with a 300 mm defined area and 30 mm resolution (hand detection). When any beam is interrupted, both OSSD safety outputs switch off; the lighted end cap shows clear, weak beam, blocked beam or fault from a distance.

• Defined area: 300 mm; resolution 30 mm; response time 7.5 ms
• Operating range: 0.1...12 m
• Outputs: two redundant PNP OSSD safety outputs, 24 V DC, max 0.5 A each; configurable pin for weak beam output or IO-Link (COM2)
• Supply: +24 V DC ±15 %, 96 mA typical without load
• Housing: anodised aluminium, 38 x 40 mm, glass-filled polycarbonate end caps
• Environment: IP65, -20...+55 °C, indoor use
• Connection: RD (removable disconnect) socket; 5-pin or 8-pin RD cordset with M12 ordered separately

With the 8-pin RD cordset the receiver monitors the contactors itself (EDM) and needs no external safety module; with the 5-pin cordset it is wired to a safety relay, safety controller or safety PLC. Reduced resolution can be switched on to ignore one blocked beam, and up to four pairs can be cascaded.

Type 4 per IEC 61496-1 and -2, Category 4 PL e per EN ISO 13849-1, SIL3 per IEC 61508. MTTFd 287 years, PFHd 3.08 × 10⁻⁹ (single pair).

S4BE30-300-S is the emitter of a Banner EZ-SCREEN S4B Type 4 safety light curtain with a 300 mm defined area and 30 mm resolution (hand detection). It projects a row of synchronised, modulated infrared beams (860 nm) from end to end of the housing, so there is no dead zone at either end.

• Defined area: 300 mm; resolution 30 mm; system response time 7.5 ms
• Operating range: 0.1...12 m
• Indicators: bi-colour status indicator, two tri-colour scan code indicators
• Supply: +24 V DC ±15 %, 33 mA typical
• Housing: anodised aluminium, 38 x 40 mm, glass-filled polycarbonate end caps
• Environment: IP65, -20...+55 °C, indoor use
• Connection: RD (removable disconnect) socket; RD cordset with M12 ordered separately

The emitter works only as a pair with an S4B receiver of the same length and resolution. The scan code (1 or 2) is set with switches in the RD cordset, so that two pairs mounted close to each other do not interfere.

Type 4 per IEC 61496-1 and -2, Category 4 PL e per EN ISO 13849-1, SIL3 per IEC 61508. MTTFd 287 years, PFHd 3.08 × 10⁻⁹ (single pair).

S4BE14-300-S is the emitter of a Banner EZ-SCREEN S4B Type 4 safety light curtain with a 300 mm defined area and 14 mm resolution (finger detection). It projects a row of synchronised, modulated infrared beams (860 nm) from end to end of the housing, so there is no dead zone at either end.

• Defined area: 300 mm; resolution 14 mm; system response time 11.5 ms
• Operating range: 0.1...12 m
• Indicators: bi-colour status indicator, two tri-colour scan code indicators
• Supply: +24 V DC ±15 %, 33 mA typical
• Housing: anodised aluminium, 38 x 40 mm, glass-filled polycarbonate end caps
• Environment: IP65, -20...+55 °C, indoor use
• Connection: RD (removable disconnect) socket; RD cordset with M12 ordered separately

The emitter works only as a pair with an S4B receiver of the same length and resolution. The scan code (1 or 2) is set with switches in the RD cordset, so that two pairs mounted close to each other do not interfere.

Type 4 per IEC 61496-1 and -2, Category 4 PL e per EN ISO 13849-1, SIL3 per IEC 61508. MTTFd 289 years, PFHd 3.05 × 10⁻⁹ (single pair).

S4BR14-300-S is the receiver of a Banner EZ-SCREEN S4B Type 4 safety light curtain with a 300 mm defined area and 14 mm resolution (finger detection). When any beam is interrupted, both OSSD safety outputs switch off; the lighted end cap shows clear, weak beam, blocked beam or fault from a distance.

• Defined area: 300 mm; resolution 14 mm; response time 11.5 ms
• Operating range: 0.1...12 m
• Outputs: two redundant PNP OSSD safety outputs, 24 V DC, max 0.5 A each; configurable pin for weak beam output or IO-Link (COM2)
• Supply: +24 V DC ±15 %, 96 mA typical without load
• Housing: anodised aluminium, 38 x 40 mm, glass-filled polycarbonate end caps
• Environment: IP65, -20...+55 °C, indoor use
• Connection: RD (removable disconnect) socket; 5-pin or 8-pin RD cordset with M12 ordered separately

With the 8-pin RD cordset the receiver monitors the contactors itself (EDM) and needs no external safety module; with the 5-pin cordset it is wired to a safety relay, safety controller or safety PLC. Reduced resolution can be switched on to ignore one blocked beam, and up to four pairs can be cascaded.

Type 4 per IEC 61496-1 and -2, Category 4 PL e per EN ISO 13849-1, SIL3 per IEC 61508. MTTFd 289 years, PFHd 3.05 × 10⁻⁹ (single pair).

EA5R1050PIXMODQ is the receiver of a Banner EZ-ARRAY measuring light curtain with a 1050 mm array of 210 beams at 5 mm spacing. The controller is built into the receiver: it evaluates the beam pattern and reports object position, height, width or count through two analog outputs, two discrete outputs and Modbus RTU.

• Resolution: 5 mm straight scan, 2.5 mm edge scan; minimum object 5 mm (low-contrast mode)
• Range: 400 mm...4 m between emitter and receiver
• Outputs: 2x analog 4-20 mA, 2x PNP 100 mA, Modbus RTU over RS485 (up to 15 nodes)
• Supply: 12-30 V DC, 105 mA at 24 V
• Housing: clear-anodised aluminium, acrylic lens cover; end-cap brackets and centre bracket included
• Environment: IP65, -40...+70 °C
• Connection: M12, 8-pin; cordset ordered separately

The receiver is configured with its six-position DIP switch or with the supplied PC software; a straight scan takes 2.8...26.5 ms depending on array length. It works with the EZ-ARRAY emitter of the same length, and each unit needs its own 8-pin M12 cordset.

S4BE30-600-S is the emitter of a Banner EZ-SCREEN S4B Type 4 safety light curtain with a 600 mm defined area and 30 mm resolution (hand detection). It projects a row of synchronised, modulated infrared beams (860 nm) from end to end of the housing, so there is no dead zone at either end.

• Defined area: 600 mm; resolution 30 mm; system response time 10.0 ms
• Operating range: 0.1...12 m
• Indicators: bi-colour status indicator, two tri-colour scan code indicators
• Supply: +24 V DC ±15 %, 33 mA typical
• Housing: anodised aluminium, 38 x 40 mm, glass-filled polycarbonate end caps
• Environment: IP65, -20...+55 °C, indoor use
• Connection: RD (removable disconnect) socket; RD cordset with M12 ordered separately

The emitter works only as a pair with an S4B receiver of the same length and resolution. The scan code (1 or 2) is set with switches in the RD cordset, so that two pairs mounted close to each other do not interfere.

Type 4 per IEC 61496-1 and -2, Category 4 PL e per EN ISO 13849-1, SIL3 per IEC 61508. MTTFd 287 years, PFHd 3.08 × 10⁻⁹ (single pair).

S4BR30-600-S is the receiver of a Banner EZ-SCREEN S4B Type 4 safety light curtain with a 600 mm defined area and 30 mm resolution (hand detection). When any beam is interrupted, both OSSD safety outputs switch off; the lighted end cap shows clear, weak beam, blocked beam or fault from a distance.

• Defined area: 600 mm; resolution 30 mm; response time 10.0 ms
• Operating range: 0.1...12 m
• Outputs: two redundant PNP OSSD safety outputs, 24 V DC, max 0.5 A each; configurable pin for weak beam output or IO-Link (COM2)
• Supply: +24 V DC ±15 %, 96 mA typical without load
• Housing: anodised aluminium, 38 x 40 mm, glass-filled polycarbonate end caps
• Environment: IP65, -20...+55 °C, indoor use
• Connection: RD (removable disconnect) socket; 5-pin or 8-pin RD cordset with M12 ordered separately

With the 8-pin RD cordset the receiver monitors the contactors itself (EDM) and needs no external safety module; with the 5-pin cordset it is wired to a safety relay, safety controller or safety PLC. Reduced resolution can be switched on to ignore one blocked beam, and up to four pairs can be cascaded.

Type 4 per IEC 61496-1 and -2, Category 4 PL e per EN ISO 13849-1, SIL3 per IEC 61508. MTTFd 287 years, PFHd 3.08 × 10⁻⁹ (single pair).

EA5E1200Q is the emitter of a Banner EZ-ARRAY measuring light curtain, with a 1200 mm array of 240 infrared beams at 5 mm spacing. It is synchronised with the receiver over the cable, and all evaluation and outputs are in the receiver.

• Array: 1200 mm, 240 beams, 5 mm spacing, infrared LED
• Range: 400 mm...4 m between emitter and receiver
• Supply: 12-30 V DC, 80 mA at 24 V
• Housing: clear-anodised aluminium, acrylic lens cover; end-cap brackets and centre bracket included
• Environment: IP65, -40...+70 °C
• Connection: M12, 8-pin; cordset ordered separately

It works with an EZ-ARRAY receiver of the same length, which sets the outputs and the Modbus interface.

EA5R1200PIXMODQ is the receiver of a Banner EZ-ARRAY measuring light curtain with a 1200 mm array of 240 beams at 5 mm spacing. The controller is built into the receiver: it evaluates the beam pattern and reports object position, height, width or count through two analog outputs, two discrete outputs and Modbus RTU.

• Resolution: 5 mm straight scan, 2.5 mm edge scan; minimum object 5 mm (low-contrast mode)
• Range: 400 mm...4 m between emitter and receiver
• Outputs: 2x analog 4-20 mA, 2x PNP 100 mA, Modbus RTU over RS485 (up to 15 nodes)
• Supply: 12-30 V DC, 120 mA at 24 V
• Housing: clear-anodised aluminium, acrylic lens cover; end-cap brackets and centre bracket included
• Environment: IP65, -40...+70 °C
• Connection: M12, 8-pin; cordset ordered separately

The receiver is configured with its six-position DIP switch or with the supplied PC software; a straight scan takes 2.8...26.5 ms depending on array length. It works with the EZ-ARRAY emitter of the same length, and each unit needs its own 8-pin M12 cordset.

S4BE30-900-S is the emitter of a Banner EZ-SCREEN S4B Type 4 safety light curtain with a 900 mm defined area and 30 mm resolution (hand detection). It projects a row of synchronised, modulated infrared beams (860 nm) from end to end of the housing, so there is no dead zone at either end.

• Defined area: 900 mm; resolution 30 mm; system response time 12.5 ms
• Operating range: 0.1...12 m
• Indicators: bi-colour status indicator, two tri-colour scan code indicators
• Supply: +24 V DC ±15 %, 33 mA typical
• Housing: anodised aluminium, 38 x 40 mm, glass-filled polycarbonate end caps
• Environment: IP65, -20...+55 °C, indoor use
• Connection: RD (removable disconnect) socket; RD cordset with M12 ordered separately

The emitter works only as a pair with an S4B receiver of the same length and resolution. The scan code (1 or 2) is set with switches in the RD cordset, so that two pairs mounted close to each other do not interfere.

Type 4 per IEC 61496-1 and -2, Category 4 PL e per EN ISO 13849-1, SIL3 per IEC 61508. MTTFd 287 years, PFHd 3.08 × 10⁻⁹ (single pair).

S4BR30-900-S is the receiver of a Banner EZ-SCREEN S4B Type 4 safety light curtain with a 900 mm defined area and 30 mm resolution (hand detection). When any beam is interrupted, both OSSD safety outputs switch off; the lighted end cap shows clear, weak beam, blocked beam or fault from a distance.

• Defined area: 900 mm; resolution 30 mm; response time 12.5 ms
• Operating range: 0.1...12 m
• Outputs: two redundant PNP OSSD safety outputs, 24 V DC, max 0.5 A each; configurable pin for weak beam output or IO-Link (COM2)
• Supply: +24 V DC ±15 %, 96 mA typical without load
• Housing: anodised aluminium, 38 x 40 mm, glass-filled polycarbonate end caps
• Environment: IP65, -20...+55 °C, indoor use
• Connection: RD (removable disconnect) socket; 5-pin or 8-pin RD cordset with M12 ordered separately

With the 8-pin RD cordset the receiver monitors the contactors itself (EDM) and needs no external safety module; with the 5-pin cordset it is wired to a safety relay, safety controller or safety PLC. Reduced resolution can be switched on to ignore one blocked beam, and up to four pairs can be cascaded.

Type 4 per IEC 61496-1 and -2, Category 4 PL e per EN ISO 13849-1, SIL3 per IEC 61508. MTTFd 287 years, PFHd 3.08 × 10⁻⁹ (single pair).

LX3E is the emitter of a Banner LX series part-sensing light curtain with a 67 mm sensing array. It sends a strobed web of modulated beams to the matching LX receiver for detecting small or flat parts passing anywhere through the screen.

• Sensing range: 300 mm to 2 m with the matching receiver
• Output: none (emitter)
• Supply: 10-30 V DC, < 1 W
• Housing: aluminium, die-cast zinc end caps, acrylic window
• Environment: IP65, -20...+70 °C
• Connection: 2 m PVC cable, 5 wires

Needs the LX receiver of the same array length, ordered separately; no synchronisation wire is needed. Green LED shows power, red LED reduced range or a fault. Not for personnel protection. Best resolution is within the centre 80 % of the sensing range.

LX12R is the receiver of a Banner LX series part-sensing light curtain with a 295 mm sensing array. Its outputs switch while any part, down to 9.5 mm diameter, passes anywhere through the web of beams from the matching emitter.

• Sensing range: 300 mm to 2 m (reduced range 150-600 mm)
• Minimum object: 9.5 mm diameter
• Output: bipolar, 1 PNP and 1 NPN, 125 mA each; response 3.2 ms ON, 8.5 ms OFF
• Supply: 10-30 V DC, < 1 W
• Housing: aluminium, die-cast zinc end caps, acrylic window
• Environment: IP65, -20...+70 °C
• Connection: 2 m PVC cable, 5 wires

Emitter and receiver need no synchronisation wire. The off-time includes a 5 ms pulse stretcher, so short parts still give a readable output pulse. Not for personnel protection. Best resolution is within the centre 80 % of the sensing range.

LX12E is the emitter of a Banner LX series part-sensing light curtain with a 295 mm sensing array. It sends a strobed web of modulated beams to the matching LX receiver for detecting small or flat parts passing anywhere through the screen.

• Sensing range: 300 mm to 2 m with the matching receiver
• Output: none (emitter)
• Supply: 10-30 V DC, < 1 W
• Housing: aluminium, die-cast zinc end caps, acrylic window
• Environment: IP65, -20...+70 °C
• Connection: 2 m PVC cable, 5 wires

Needs the LX receiver of the same array length, ordered separately; no synchronisation wire is needed. Green LED shows power, red LED reduced range or a fault. Not for personnel protection. Best resolution is within the centre 80 % of the sensing range.

S4BR30-1200-S is the receiver of a Banner EZ-SCREEN S4B Type 4 safety light curtain with a 1200 mm defined area and 30 mm resolution (hand detection). When any beam is interrupted, both OSSD safety outputs switch off; the lighted end cap shows clear, weak beam, blocked beam or fault from a distance.

• Defined area: 1200 mm; resolution 30 mm; response time 15.0 ms
• Operating range: 0.1...12 m
• Outputs: two redundant PNP OSSD safety outputs, 24 V DC, max 0.5 A each; configurable pin for weak beam output or IO-Link (COM2)
• Supply: +24 V DC ±15 %, 96 mA typical without load
• Housing: anodised aluminium, 38 x 40 mm, glass-filled polycarbonate end caps
• Environment: IP65, -20...+55 °C, indoor use
• Connection: RD (removable disconnect) socket; 5-pin or 8-pin RD cordset with M12 ordered separately

With the 8-pin RD cordset the receiver monitors the contactors itself (EDM) and needs no external safety module; with the 5-pin cordset it is wired to a safety relay, safety controller or safety PLC. Reduced resolution can be switched on to ignore one blocked beam, and up to four pairs can be cascaded. Models longer than 900 mm need an additional side mount bracket.

Type 4 per IEC 61496-1 and -2, Category 4 PL e per EN ISO 13849-1, SIL3 per IEC 61508. MTTFd 287 years, PFHd 3.08 × 10⁻⁹ (single pair).

S4BE30-1200-S is the emitter of a Banner EZ-SCREEN S4B Type 4 safety light curtain with a 1200 mm defined area and 30 mm resolution (hand detection). It projects a row of synchronised, modulated infrared beams (860 nm) from end to end of the housing, so there is no dead zone at either end.

• Defined area: 1200 mm; resolution 30 mm; system response time 15.0 ms
• Operating range: 0.1...12 m
• Indicators: bi-colour status indicator, two tri-colour scan code indicators
• Supply: +24 V DC ±15 %, 33 mA typical
• Housing: anodised aluminium, 38 x 40 mm, glass-filled polycarbonate end caps
• Environment: IP65, -20...+55 °C, indoor use
• Connection: RD (removable disconnect) socket; RD cordset with M12 ordered separately

The emitter works only as a pair with an S4B receiver of the same length and resolution. The scan code (1 or 2) is set with switches in the RD cordset, so that two pairs mounted close to each other do not interfere. Models longer than 900 mm need an additional side mount bracket.

Type 4 per IEC 61496-1 and -2, Category 4 PL e per EN ISO 13849-1, SIL3 per IEC 61508. MTTFd 287 years, PFHd 3.08 × 10⁻⁹ (single pair).