EN380.IL-BF12.5C1H1.00500.H is a Baumer EN380 series incremental encoder with optical sensing, a blind hollow shaft and a stator coupling. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 500 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, blind hollow shaft ø12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder slides onto a motor or gearbox shaft end and the stator coupling holds the housing against rotation, so neither a coupling nor a separate bracket is needed. Permissible speed is 6000 rpm up to +75 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-TG06.5C1H1.02048.H is a Baumer EN380 series incremental encoder with optical sensing, a through hollow shaft and a torque pin. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 2048 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, through hollow shaft ø6 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The shaft passes right through the encoder, so it also fits where the shaft continues on both sides, and the torque pin holds the housing against rotation. Permissible speed is 6000 rpm up to +60 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-TG06.5C1H1.00360.H is a Baumer EN380 series incremental encoder with optical sensing, a through hollow shaft and a torque pin. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 360 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, through hollow shaft ø6 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The shaft passes right through the encoder, so it also fits where the shaft continues on both sides, and the torque pin holds the housing against rotation. Permissible speed is 6000 rpm up to +60 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-TF06.5C1H1.02048.H is a Baumer EN380 series incremental encoder with optical sensing, a through hollow shaft and a stator coupling. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 2048 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, through hollow shaft ø6 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The shaft passes right through the encoder, so it also fits where the shaft continues on both sides, and the stator coupling holds the housing against rotation. Permissible speed is 6000 rpm up to +60 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-TF06.5C1H1.01024.H is a Baumer EN380 series incremental encoder with optical sensing, a through hollow shaft and a stator coupling. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 1024 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, through hollow shaft ø6 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The shaft passes right through the encoder, so it also fits where the shaft continues on both sides, and the stator coupling holds the housing against rotation. Permissible speed is 6000 rpm up to +60 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

QS30LDLQ is a Banner QS30 series diffuse-mode laser sensor with a Class 2 visible red 658 nm laser and an 800 mm range. The spot is about 1 mm at 800 mm, so it detects small parts and low-contrast targets at a distance.

• Sensing range: 800 mm, spot approx. 1 mm at 800 mm
• Output: bipolar, one PNP and one NPN, Light or Dark Operate, 150 mA each
• Response: 500 µs; repeatability 70 µs; selectable 30 ms OFF-delay
• Supply: 10-30 V DC, < 35 mA
• Housing: ABS, acrylic lens cover, 30 mm threaded nose or side mounting
• Environment: IP67, -10...+50 °C
• Connection: integral M12 5-pin male connector

The switch point is taught with two push buttons or the remote wire: two-point static, dynamic, window, light set and dark set, then fine-tuned with the +/- buttons. An 8-segment bar graph shows the signal relative to the switch point; the remote wire also locks the buttons and resets to factory defaults.

Class 2 laser product per IEC 60825-1:2014. Vibration tested to MIL-STD-202F, method 201A; shock to IEC 60947-5-2.

The Banner SD50 Wireless Communication Kit enables fast, clear messaging across industrial facilities without complex wiring. This starter kit includes one DXMR90 controller, one R70SR radio, and one SD50 display. Additional SD50 displays can be added to expand the system to multiple locations.

DXMR90-X1E Industrial Controller - Network hub supporting EtherNet/IP, Modbus TCP, Modbus RTU, PROFINET, and MQTT/Sparkplug B protocols. IP67/IP68 rated with dual M12 Ethernet ports. 12-30V DC power supply.

R70SR2MQ Serial Data Radio - 2.4 GHz multihop wireless radio with 65mW output. RS-485 interface, internal antenna, IP65 rated. Supports point-to-point, point-to-multipoint, star, and tree topologies.

SD50P300WSR2QP Wireless Status Display - 300mm white LED display (8×96 pixels) with RGB indicators. Configure wirelessly via Pro Editor software without coding. IP65 polycarbonate housing. 12-30V DC.

Configuration Options:

• Discrete models: Configure via Pro Editor - define text, colors, animations without coding or PLC programming
• IO-Link models: Integrate with IO-Link networks for remote diagnostics and standardized connectivity
• Wireless models: Configure through Modbus registers, update messages as conditions change

Expandable System: Add multiple SD50 displays to communicate across different zones, production lines, or departments using the same controller and radio infrastructure.

WKH4.4-20/TFE is a TURCK hygienic connection cable with an angled M12 female connector (4-pin) on one end and open cores on the other, for sensors and actuators in food and beverage plants.

• Connector: M12 female, angled, 4-pin, gold-plated brass (CuZn) contacts
• Cable: 20 m, PVC, grey RAL 7040, Ø 4.5 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 250 V, test voltage 1500 V, more than 100 mating cycles
• Housing: grey PP, stainless steel (V4A) coupling nut, FPM/FKM seal
• Environment: IP65, IP67, IP68, IP69 (only when screwed in); -25...+80°C fixed, 0...+80°C mobile

Designed for food and beverage areas: the grey PVC jacket (RAL 7040) resists acids, alkalis, oils and chemicals and is flame retardant per DIN EN 60332-1-2 and 60332-2-2. RoHS and REACH compliant. Approvals: GOST, Ecolab.

WKH4.4-25/TFE is a TURCK hygienic connection cable with an angled M12 female connector (4-pin) on one end and open cores on the other, for sensors and actuators in food and beverage plants.

• Connector: M12 female, angled, 4-pin, gold-plated brass (CuZn) contacts
• Cable: 25 m, PVC, grey RAL 7040, Ø 4.5 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 250 V, more than 100 mating cycles
• Housing: grey PP, stainless steel (V4A) coupling nut, FPM/FKM seal
• Environment: IP65, IP67, IP68, IP69 (only when screwed in); -25...+80°C fixed, 0...+80°C mobile

Designed for food and beverage areas: the grey PVC jacket (RAL 7040) resists acids, alkalis, oils and chemicals and is flame retardant per DIN EN 60332-1-2 and 60332-2-2. RoHS and REACH compliant. Approvals: GOST, Ecolab.

WKH4.4-30/TFE is a TURCK hygienic connection cable with an angled M12 female connector (4-pin) on one end and open cores on the other, for sensors and actuators in food and beverage plants.

• Connector: M12 female, angled, 4-pin, gold-plated brass (CuZn) contacts
• Cable: 30 m, PVC, grey RAL 7040, Ø 4.5 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 250 V, more than 100 mating cycles
• Housing: grey PP, stainless steel (V4A) coupling nut, FPM/FKM seal
• Environment: IP65, IP67, IP68, IP69 (only when screwed in); -25...+80°C fixed, 0...+80°C mobile

Designed for food and beverage areas: the grey PVC jacket (RAL 7040) resists acids, alkalis, oils and chemicals and is flame retardant per DIN EN 60332-1-2 and 60332-2-2. RoHS and REACH compliant. Approvals: GOST, Ecolab.

K30LGXXPQ is a single-colour green LED indicator from the Banner EZ-LIGHT K30L series. It is driven directly from the discrete PNP output of a 3-wire or 4-wire sensor or from a PLC output, without a relay and without an amplifier.

• Indication: single colour - green, the whole dome emits light
• Input: PNP, on and off response time up to 1 ms
• Supply: 10...30 V DC, up to 25 mA
• Housing: polycarbonate base with M22x1.5 thread, translucent polycarbonate dome, Ø30 mm, height 58 mm, fully encapsulated electronics
• Environment: IP67 and IP69K per DIN 40050-9, -40...+50 °C
• Connection: integral M12 male connector, 4-pin

The indicator mounts in a 22 mm hole and shows machine or process status at the workplace - at a conveyor, a packaging machine station or a control desk. The QD version needs a separately ordered M12 cordset, as one is not included.

CE compliant, K30L models are cULus Listed.

TL50BGYRAQ is a Banner TL50 series 50 mm LED tower light with 4 colour segments: blue, green, yellow, red, from the bottom up, topped by a audible alarm. Each colour has its own input wire and the inputs are bimodal, so the tower can be driven from either PNP or NPN controller outputs.

• Colours: blue 470 nm, green 528 nm, yellow 590 nm, red 625 nm
• Audible: continuous tone, 2.7 kHz, up to 92 dB at 1 m, adjustable down to 62 dB
• Inputs: bimodal (PNP or NPN), one per colour, response 10 ms
• Supply: 18-30 V DC or 24 V AC 50/60 Hz, up to 45 mA per colour, alarm 25 mA
• Housing: Ø50 x 241.5 mm, ABS base and covers, polycarbonate light segments, black, M30x1.5 base mount
• Environment: IP50, -20...+50 °C
• Connection: integral M12 male connector, 8-pin

The tower connects through a separately ordered 8-pin M12 female cordset. Audible intensity is adjusted by unscrewing the top cover by up to 1.5 turns.

Vibration tested to IEC 60068-2-6, shock to IEC 60068-2-27 (30 g, 11 ms).

S4BE30-900-S is the emitter of a Banner EZ-SCREEN S4B Type 4 safety light curtain with a 900 mm defined area and 30 mm resolution (hand detection). It projects a row of synchronised, modulated infrared beams (860 nm) from end to end of the housing, so there is no dead zone at either end.

• Defined area: 900 mm; resolution 30 mm; system response time 12.5 ms
• Operating range: 0.1...12 m
• Indicators: bi-colour status indicator, two tri-colour scan code indicators
• Supply: +24 V DC ±15 %, 33 mA typical
• Housing: anodised aluminium, 38 x 40 mm, glass-filled polycarbonate end caps
• Environment: IP65, -20...+55 °C, indoor use
• Connection: RD (removable disconnect) socket; RD cordset with M12 ordered separately

The emitter works only as a pair with an S4B receiver of the same length and resolution. The scan code (1 or 2) is set with switches in the RD cordset, so that two pairs mounted close to each other do not interfere.

Type 4 per IEC 61496-1 and -2, Category 4 PL e per EN ISO 13849-1, SIL3 per IEC 61508. MTTFd 287 years, PFHd 3.08 × 10⁻⁹ (single pair).

S4BR30-900-S is the receiver of a Banner EZ-SCREEN S4B Type 4 safety light curtain with a 900 mm defined area and 30 mm resolution (hand detection). When any beam is interrupted, both OSSD safety outputs switch off; the lighted end cap shows clear, weak beam, blocked beam or fault from a distance.

• Defined area: 900 mm; resolution 30 mm; response time 12.5 ms
• Operating range: 0.1...12 m
• Outputs: two redundant PNP OSSD safety outputs, 24 V DC, max 0.5 A each; configurable pin for weak beam output or IO-Link (COM2)
• Supply: +24 V DC ±15 %, 96 mA typical without load
• Housing: anodised aluminium, 38 x 40 mm, glass-filled polycarbonate end caps
• Environment: IP65, -20...+55 °C, indoor use
• Connection: RD (removable disconnect) socket; 5-pin or 8-pin RD cordset with M12 ordered separately

With the 8-pin RD cordset the receiver monitors the contactors itself (EDM) and needs no external safety module; with the 5-pin cordset it is wired to a safety relay, safety controller or safety PLC. Reduced resolution can be switched on to ignore one blocked beam, and up to four pairs can be cascaded.

Type 4 per IEC 61496-1 and -2, Category 4 PL e per EN ISO 13849-1, SIL3 per IEC 61508. MTTFd 287 years, PFHd 3.08 × 10⁻⁹ (single pair).

S4BA-ML-LPQ20 is an L-configuration mute arm kit for Banner EZ-SCREEN S4B safety light curtains: one sensor arm with two Q20-2 retroreflective sensors and one reflector arm with two reflectors, all pre-installed. Together with an S4B pair and a Banner safety controller it forms a muting system.

• Included: 1 sensor arm with 2 S4BA-Q20-2VPLP-Q5 sensors, 1 reflector arm with 2 reflectors, mounting hardware for sensors and reflectors
• Sensors: retroreflective, visible red LED, up to 5 m, PNP, 10-30 V DC, light/dark operate
• Connection: 600 mm cable with 4-pin M12 connector per sensor
• Arms: 4 mm aluminium, black anodised; 50 x 50 x 400 mm
• Environment: IP67, -25...+70 °C

The arm mounts to an S4BA-MBK-16 bracket or directly to a flat surface; the M4 hardware for this is not included. Single-sided, left or right.

S4BA-MBK-16 is a side mount bracket kit for Banner EZ-SCREEN S4B safety light curtains, with ±15° rotation. Because the S4B beams run to both ends of the housing, units mounted on these brackets leave minimal or no gaps in detection.

• Fits: all S4B emitters and receivers
• Included: 2 brackets
• Material: glass-filled polycarbonate
• Mounting: 4 holes Ø4.5 mm, 25 mm hole spacing
• Adjustment: ±15° rotation

FID 4 S4B units passed the IEC 61496-1 (Class 3M4) vibration and shock tests mounted on S4BA-MBK-16 brackets.

RKC4.5T-10/TEL is a TURCK connection cable with a straight M12 female connector (5-pin) on one end and open cores on the other.

• Connector: M12 x 1 female, straight, A-coded, 5-pin, gold-plated brass (CuZn) contacts
• Cable: 10 m, PVC, black, Ø 5 mm, 5 x 0.34 mm², core colours BN, WH, BU, BK, GY
• Ratings: 4 A, 60 V, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nut, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -40...+105°C fixed, -5...+80°C mobile

The PVC jacket resists chemicals, oils, acids, alkaline solutions, microbes and hydrolysis, is flame retardant and free from LABS. Approval: cULus.

Q5ZKLAF1800-Q8 is a Banner Q5Z Global series Class 2 laser measurement sensor with a 95...1800 mm range and two switching outputs. It has no display and a single TEACH button: it ships pre-configured from the factory, and any other setting is made over IO-Link.

• Repeatability: ±0.5 mm at 95...300 mm, ±0.25 % at 300...1000 mm, ±0.52 % at 1000...1800 mm
• Sensing range: 95...1800 mm
• Output 1: IO-Link push/pull (default), configurable PNP or NPN, 50 mA
• Output 2: PNP (default), configurable PNP/NPN, pulse frequency output or remote input, 50 mA; response time 3, 5, 15, 25 or 50 ms
• Supply: 10...30 V DC, < 1 W; protected against reverse polarity and transient overvoltage
• Housing: ABS, PMMA lens cover; side mounting
• Environment: IP67, -10...+50 °C
• Connection: integral M12 male connector, 4-pin, rotatable through 270°

It detects black targets below 6 % reflectance, also against a black or shiny metal background. Configuration and process data run over IO-Link v1.1 with Smart Sensor Profile.

CE, UKCA and UL listed (Industrial Control Equipment). Vibration per MIL-STD-202G method 201A, shock per MIL-STD-202G method 213B (100 G).

SMB22A is a Banner right-angle bracket for sensors with a 22 mm housing. The curved slot lets the sensor be turned before the screws are tightened.

• Sensor hole: Ø22.2 mm
• Mounting: Ø4.6 mm hole and 4.6 x 16.9 mm slot, 26.0 mm hole centre spacing
• Material: 12-gauge stainless steel

BTA23S is a Banner bifurcated glass fibre for diffuse mode with a 5/16-24 UNF thread and an angled sensing tip, so the beam exits at a right angle to the fibre.

• Type: diffuse, bifurcated, right-angle beam exit
• Length: 914 mm, bundle Ø3.2 mm
• Tip: 5/16-24 UNF thread with angled end, Ø4.8 mm
• Sheath: stainless steel monocoil
• Bend radius: at least 25 mm
• Temperature: -140...+249 °C

The fibre ends are ground and polished, so the assembly cannot be shortened or spliced. Glass fibres carry infrared as well as visible light; Banner recommends them for IR sensors.

WLS28-2XW285SQ is a Banner WLS28-2 series LED strip light with a 285 mm lit length, in a clear anodised aluminium housing sealed for washdown. The black wire selects full or 50 % light output.

• Light: cool white 6500 K, 800 lm, CRI 85
• Light level: black wire to +V gives 50 %, floating or to common gives 100 %
• Supply: 12-30 V DC
• Housing: 326 x 28 x 20.9 mm, anodised aluminium, polycarbonate window, two swivel brackets included
• Environment: IP65, IP67, IP69K, -40...+70 °C
• Connection: integral M12 male connector, 4-pin

Light output falls above 50 °C, to about 65 % at 60 °C. LED service life 75,000 h (L70). UL, CE and UKCA approved.

Q45BB6RQ5 is the receiver of a Banner Q45 series opposed-mode photo sensor pair. It switches when an object breaks the infrared beam from a Q45 emitter up to 60 m away, with one PNP and one NPN output.

• Sensing range: 60 m with a Q45 emitter
• Output: bipolar, 1 PNP and 1 NPN, Light or Dark Operate by switch
• Response: 2 ms ON, 1 ms OFF; repeatability 250 µs
• Supply: 10-30 V DC
• Housing: rugged rectangular, thermoplastic, acrylic lens, 30 mm threaded mounting hub
• Environment: IP67, NEMA 4X, -40...+70 °C
• Connection: integral M12 male connector, 4-pin

Needs a Q45 emitter, ordered separately. Sensitivity is set with a multi-turn control, and the signal strength indicator helps with alignment. CE approved.

WKS8T-2/TXL is a TURCK shielded connection cable with an angled M12 female connector (8-pin) on one end and open cores on the other. The cable shield is connected to the coupling nut.

• Connector: M12 x 1, female, angled, A-coded, 8-pin, gold-plated brass (CuZn) contacts
• Cable: 2 m, PUR, black, Ø 6.3 mm, 8 x 0.25 mm², core colours BN, WH, BU, BK, GY, PK, VT, OG
• Shield: aluminium foil and tinned copper wire
• Ratings: 2 A, 30 V, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nut, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 2 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The PUR jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.

VBRS4.4-2RKC4.4T-0.3/0.3/TXL is a TURCK Y-splitter with a straight M12 male connector (4-pin) and two straight M12 female connectors (4-pin) on 0.3 m PUR cable branches.

• Connectors: M12 x 1 male, 4-pin / 2 x M12 x 1 female, 4-pin, all straight, gold-plated brass (CuZn) contacts
• Cable: 2 x 0.3 m, PUR, black, Ø 4.7 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 250 V, test voltage 2000 V, more than 100 mating cycles
• Housing: black TPU, nickel-plated brass coupling nuts, FPM/FKM seal; tightening torque 0.8...1 Nm
• Environment: IP67 (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain

The PUR jacket is rated for drag chains: at least 5 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m. It resists chemicals, UV radiation, oils and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS.

RoHS compliant.

SMBAMSQ5XIPRA is a Banner enclosed bracket that houses the sensor behind a borosilicate glass window and protects it from side impact. The right-angle mount plate mounts it at 90° to the mounting surface.

• Type: enclosed bracket, right-angle mount plate
• Material: 13-gauge stainless steel
• Window: borosilicate glass, replaceable
• Mounting: AMS slot pattern, Ø 6.7 mm holes
• Included: 1 bracket with hardware pack

BC-M12F4-M12M4-22-1 is a Banner double-ended M12 extension cordset with a straight 4-pin female connector at one end and a straight 4-pin male connector at the other. The cable is rated as UL ITC/PLTC tray cable, so it can be laid in cable trays without conduit where those approvals apply.

• Connectors: M12x1, female / male, straight, A-coded, 4-pin; length 1 m
• Cable: black PVC, 22 AWG, 4 conductors, Ø 5.33 mm, unshielded
• Ratings: 4 A, 30 V
• Body: TPU connector body, nickel-plated brass coupling nut
• Environment: IP66, IP67, IP68, -40...+105 °C

Wire colours: brown 1, white 2, blue 3, black 4; pin 5 not used. Bend radius at least 4x the cable diameter fixed and 15x in motion; vibration per IEC 60068-2-6, shock per IEC 60068-2-27.

BC-M12F4-M12M4-22-5 is a Banner double-ended M12 extension cordset with a straight 4-pin female connector at one end and a straight 4-pin male connector at the other. The cable is rated as UL ITC/PLTC tray cable, so it can be laid in cable trays without conduit where those approvals apply.

• Connectors: M12x1, female / male, straight, A-coded, 4-pin; length 5 m
• Cable: black PVC, 22 AWG, 4 conductors, Ø 5.33 mm, unshielded
• Ratings: 4 A, 30 V
• Body: TPU connector body, nickel-plated brass coupling nut
• Environment: IP66, IP67, IP68, -40...+105 °C

Wire colours: brown 1, white 2, blue 3, black 4; pin 5 not used. Bend radius at least 4x the cable diameter fixed and 15x in motion; vibration per IEC 60068-2-6, shock per IEC 60068-2-27.

LMBE12RA45 is a Banner right-angle bracket for mounting an indicator light on a stand-off pipe with a 1/2-14 NPSM nut. The centre of the nut sits 45 mm from the wall.

• Fits: stand-off pipe with 1/2-14 NPSM nut
• Offset: 45 mm from the mounting surface to the nut centre
• Mounting: 2x Ø11 mm holes, 35.0 mm hole centre spacing
• Material: zinc-plated steel

BCD-M12DM-RJ45-2 is a Banner Ethernet cordset that connects a device with a D-coded M12 socket to an RJ45 port on a switch, PC or controller. The RJ45 plug has a metal shell connected to the cable braid.

• Connectors: M12 male, D-coded, 4-pin / RJ45 male; length 2 m
• Cable: Ethernet Cat5e, 22 AWG, Ø 7 mm, black TPU overmould, braided shield
• Ratings: 1.5 A, 60 V DC
• Bend radius: more than 10x the cable diameter
• Temperature: -40...+80 °C fixed, -20...+80 °C flexible installation

Wiring: M12 pin 1 to RJ45 pin 1 (white/orange), 3 to 2 (orange), 2 to 3 (white/green), 4 to 6 (green), braid to shell.

PSW-24-1 is a Banner plug-in power supply that delivers 24 V DC to a device with an M12 connector, for example a Sure Cross wireless node, directly from a mains socket. The plug heads are detachable: types A, C, G and I.

• Input: 100-240 V AC, 50/60 Hz
• Output: 24 V DC ±5 %, 1 A, 24 W; short-circuit protected
• Connection: 2 m cable with M12 female connector, 5-pin (pin 1 V+, pin 3 V-)
• Environment: IP20, -10...+40 °C, not for wet areas
• Efficiency: 85 % at full load

UL 1310 Class 2; emissions FCC, CISPR 22 and VCCI Class B.

BC-M12F4-M12M4-22-0.3 is a Banner double-ended M12 extension cordset with a straight 4-pin female connector at one end and a straight 4-pin male connector at the other. The cable is rated as UL ITC/PLTC tray cable, so it can be laid in cable trays without conduit where those approvals apply.

• Connectors: M12x1, female / male, straight, A-coded, 4-pin; length 0.3 m
• Cable: black PVC, 22 AWG, 4 conductors, Ø 5.33 mm, unshielded
• Ratings: 4 A, 30 V
• Body: TPU connector body, nickel-plated brass coupling nut
• Environment: IP66, IP67, IP68, -40...+105 °C

Wire colours: brown 1, white 2, blue 3, black 4; pin 5 not used. Bend radius at least 4x the cable diameter fixed and 15x in motion; vibration per IEC 60068-2-6, shock per IEC 60068-2-27.

BC-M12F4-M12M4-22-0.5 is a Banner double-ended M12 extension cordset with a straight 4-pin female connector at one end and a straight 4-pin male connector at the other. The cable is rated as UL ITC/PLTC tray cable, so it can be laid in cable trays without conduit where those approvals apply.

• Connectors: M12x1, female / male, straight, A-coded, 4-pin; length 0.5 m
• Cable: black PVC, 22 AWG, 4 conductors, Ø 5.33 mm, unshielded
• Ratings: 4 A, 30 V
• Body: TPU connector body, nickel-plated brass coupling nut
• Environment: IP66, IP67, IP68, -40...+105 °C

Wire colours: brown 1, white 2, blue 3, black 4; pin 5 not used. Bend radius at least 4x the cable diameter fixed and 15x in motion; vibration per IEC 60068-2-6, shock per IEC 60068-2-27.

TL50GYRALSQ is a Banner TL50 series 50 mm LED tower light with 3 colour segments: green, yellow, red, from the bottom up, topped by a sealed audible alarm. Each colour has its own input wire and the inputs are bimodal, so the tower can be driven from either PNP or NPN controller outputs.

• Colours: green 528 nm, yellow 590 nm, red 625 nm
• Audible: continuous tone, 2.9 kHz, up to 94 dB at 1 m, adjustable down to 74 dB
• Inputs: bimodal (PNP or NPN), one per colour, response 10 ms
• Supply: 18-30 V DC or 24 V AC 50/60 Hz, up to 45 mA per colour, alarm 35 mA
• Housing: Ø50 x 223.9 mm, ABS base and covers, polycarbonate light segments, black, M30x1.5 base mount
• Environment: IP67, -20...+50 °C
• Connection: integral M12 male connector, 5-pin

The tower connects through a separately ordered 5-pin M12 female cordset. Audible intensity is adjusted by rotating the front cover of the alarm.

Vibration tested to IEC 60068-2-6, shock to IEC 60068-2-27 (30 g, 11 ms).

WKC4.5T-0.5-RSC4.5T/TEL is a TURCK extension cable with an angled M12 female connector on one end and a straight M12 male connector on the other (5-pin).

• Connectors: M12 x 1 female, angled / M12 x 1 male, straight; A-coded, 5-pin, gold-plated brass (CuZn) contacts
• Cable: 0.5 m, PVC, black, Ø 5 mm, 5 x 0.34 mm², core colours BN, WH, BU, BK, GY
• Ratings: 4 A, 60 V, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nuts, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -40...+105°C fixed, -5...+80°C mobile

The PVC jacket resists chemicals, oils, acids, alkaline solutions, microbes and hydrolysis, is flame retardant and free from LABS. Approval: cULus.

WKC4.4T-0.5-RSC4.4T/TEL is a TURCK extension cable with an angled M12 female connector on one end and a straight M12 male connector on the other (4-pin).

• Connectors: M12 x 1 female, angled / M12 x 1 male, straight; A-coded, 4-pin, gold-plated brass (CuZn) contacts
• Cable: 0.5 m, PVC, black, Ø 4.6 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 250 V, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nuts, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -40...+105°C fixed, -5...+80°C mobile

The PVC jacket resists chemicals, oils, acids, alkaline solutions, microbes and hydrolysis, is flame retardant and free from LABS. Approval: cULus.

K50GRBPQ is a Banner K50 series 50 mm indicator that lights in three colours from one dome: green, red, blue. Each colour has its own PNP input, and a higher colour overrides a lower one, so a single indicator can show three machine states.

• Colours: green (pin 4), red (pin 2), blue (pin 1); colour 3 overrides 1 and 2
• Input: PNP, response 1 ms
• Supply: 24 V DC ±10 %, max. 55 mA per colour
• Housing: Ø 50 mm, polycarbonate base and dome, M30x1.5 thread, nut included
• Environment: IP66, IP67, IP69K, UL Type 4X and 13, -40...+50 °C
• Connection: integral M12 male connector, 4-pin; cordset ordered separately

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 g, 11 ms).

WKC5T-P7X3.2-10/TXL is a TURCK connection cable with an angled M12 female connector (4-pin + PE) on one end and open cores on the other. Pin 5 is the protective earth (PE). The connector has three built-in LED indicators: green shows the supply, yellow the PNP signal on pin 4, white the PNP signal on pin 2.

• Connector: M12 x 1, female, angled, A-coded, 4-pin + PE, gold-plated brass (CuZn) contacts
• Cable: 10 m, PUR, black, Ø 4.8 mm, 5 x 0.34 mm², core colours BN, WH, BU, BK, GNYE
• Ratings: 4 A, 30 V DC, more than 100 mating cycles
• Housing: translucent TPU, nickel-plated brass coupling nut, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 5 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The PUR jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.

Q126EQ is the emitter of a Banner Q12 series miniature opposed-mode photo sensor pair. Its visible red 640 nm beam reaches a Q12 receiver up to 2 m away; the emitter itself has no output.

• Sensing range: 2 m with a Q12 receiver
• Output: none (emitter)
• Supply: 10-30 V DC
• Housing: miniature rectangular, thermoplastic, polycarbonate lens
• Environment: IP67, -20...+55 °C
• Connection: 150 mm cable with M8 male connector, 4-pin

Needs a Q12 receiver, ordered separately. UL, CE and UKCA approved.

RKC4.4T-3-RSC4.4T/TXL is a TURCK extension cable with a straight M12 female connector on one end and a straight M12 male connector on the other (4-pin).

• Connectors: M12 x 1 female, straight, A-coded / M12 x 1 male, straight, A-coded; 4-pin, gold-plated brass (CuZn) contacts
• Cable: 3 m, PUR, black, Ø 4.5 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 250 V, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nuts, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 5 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The PUR jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.

RKC4.4T-6-RSC4.4T/TXL is a TURCK extension cable with a straight M12 female connector on one end and a straight M12 male connector on the other (4-pin).

• Connectors: M12 x 1 female, straight, A-coded / M12 x 1 male, straight, A-coded; 4-pin, gold-plated brass (CuZn) contacts
• Cable: 6 m, PUR, black, Ø 4.5 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 250 V, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nuts, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 5 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The PUR jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.

PKW4M-3-PSG4M/TXL is a TURCK extension cable with an angled M8 female connector on one end and a straight M8 male connector on the other (4-pin).

• Connectors: M8 x 1 female, angled / M8 x 1 male, straight; 4-pin, gold-plated brass (CuZn) contacts
• Cable: 3 m, PUR, black, Ø 4.5 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 50 V AC/60 V DC, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nuts, FPM/FKM seal; M8 tightening torque 0.5...0.6 Nm
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 5 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The PUR jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.

WLS28-2XW285XQ is a Banner WLS28-2 series LED strip light with a 285 mm lit length, in a clear anodised aluminium housing. The black wire selects full or 50 % light output.

• Light: cool white 6500 K, 800 lm, CRI 85
• Light level: black wire to +V gives 50 %, floating or to common gives 100 %
• Supply: 12-30 V DC
• Housing: 327 x 28 x 20.9 mm, anodised aluminium, polycarbonate window, two swivel brackets included
• Environment: IP50, -40...+70 °C
• Connection: integral M12 male connector, 4-pin

Light output falls above 50 °C, to about 65 % at 60 °C. LED service life 75,000 h (L70). UL, CE and UKCA approved.

T18-2VPDL-9M is a Banner T18-2 series diffuse sensor with visible red light that detects objects by the light they reflect back. The right-angle 18 mm threaded housing has epoxy-encapsulated electronics and food-grade plastics, for wet and washdown areas. A single-turn potentiometer sets the sensitivity.

• Sensing range: 750 mm
• Output: complementary PNP (NO and NC), 100 mA total up to +55 °C; response 1.5 ms ON / 0.75 ms OFF
• Supply: 10-30 V DC (10-24 V DC above +55 °C), < 16 mA
• Housing: right-angle, 18 mm thread, PBT polyester, PMMA window
• Environment: IP67, IP68, IP69K, -40...+70 °C; ECOLAB chemical compatibility
• Connection: 9 m PVC cable

Vibration per MIL-STD-202G method 201A, shock per method 213B (75 g operating).

LMBLC25T is a Banner stainless steel clip bracket for LC25 lights. The light snaps into the clip, which is screwed to the surface through a clearance hole for M5 hardware.

• Fits: Banner LC25
• Material: stainless steel
• Mounting: Ø 5.2 mm clearance hole for M5 hardware
• Included: 1 clip bracket and 2 plastic spacers

K50GRYPQ is a Banner K50 series 50 mm indicator that lights in three colours from one dome: green, red, yellow. Each colour has its own PNP input, and a higher colour overrides a lower one, so a single indicator can show three machine states.

• Colours: green (pin 4), red (pin 2), yellow (pin 1); colour 3 overrides 1 and 2
• Input: PNP, response 1 ms
• Supply: 24 V DC ±10 %, max. 55 mA per colour
• Housing: Ø 50 mm, polycarbonate base and dome, M30x1.5 thread, nut included
• Environment: IP66, IP67, IP69K, UL Type 4X and 13, -40...+50 °C
• Connection: integral M12 male connector, 4-pin; cordset ordered separately

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 g, 11 ms).

S18-2VNFF200-2M is a Banner S18-2 series fixed-field photo sensor with a 200 mm cutoff and a visible red 624 nm beam, in an 18 mm plastic barrel. It detects objects closer than the cutoff and ignores the background beyond it.

• Sensing range: 200 mm cutoff, fixed
• Output: complementary NPN, Light Operate and Dark Operate
• Response: 2 ms; repeatability 100 µs
• Supply: 10-30 V DC
• Housing: M18 threaded barrel, thermoplastic, acrylic lens
• Environment: IP67, NEMA 4X, -40...+70 °C
• Connection: 2 m PVC cable, 4 wires

There is no sensitivity adjustment. ECOLAB certified chemical resistance. UL and CE approved.

Temperature ranges Operational: 0 to 50° C (32-122° F) Storage: -40 to 80° C (-40 to 176° F) Calibrated: 0 to 50° C (32 to 122° F) Diameter 2.62 cm (1.03 in.) Length 14.43 cm (5.68 in.) Weight 137 g (0.30 lb) Materials Titanium, Acetal, FKM Fluoroelastomer, Ceramic Output options Rugged TROLL 100: USB or RS232 via docking station Battery type & life 3.6 V lithium; 10 years or 2M readings Memory 2.0 MB Data records 120,000 (data record = date/time plus 2 parameters logged (no wrapping) from device within the factory-calibrated temperature range) Accuracy (FS) ±0.1% Resolution ±0.01% FS or better Units of measure Pressure: psi, kPa, bar, mbar, mmHg, inHg Level: in, ft, mm, cm, m Temperature Sensor Accuracy ±0.3° C Resolution 0.01° C or better Units of measure Celsius or Fahrenheit

LMBWLS15 is a set of Banner stainless steel clip brackets for WLS15 LED light strips. The strip snaps into the clips, which are screwed to the surface through clearance holes for M5 hardware.

• Fits: Banner WLS15
• Material: stainless steel
• Mounting: Ø 5.2 mm clearance hole for M5 hardware
• Included: 3 clip brackets and 2 plastic spacers

LX3E is the emitter of a Banner LX series part-sensing light curtain with a 67 mm sensing array. It sends a strobed web of modulated beams to the matching LX receiver for detecting small or flat parts passing anywhere through the screen.

• Sensing range: 300 mm to 2 m with the matching receiver
• Output: none (emitter)
• Supply: 10-30 V DC, < 1 W
• Housing: aluminium, die-cast zinc end caps, acrylic window
• Environment: IP65, -20...+70 °C
• Connection: 2 m PVC cable, 5 wires

Needs the LX receiver of the same array length, ordered separately; no synchronisation wire is needed. Green LED shows power, red LED reduced range or a fault. Not for personnel protection. Best resolution is within the centre 80 % of the sensing range.

Q4XFULAF310-Q8 is a Banner Q4X series laser sensor with a 0-10 V analog output proportional to target distance over 35-310 mm, in a flush-mount 316L stainless steel housing. The measuring window is set with the push buttons or by remote teach.

• Resolution: < 0.3 mm at 35-110 mm, < 1 mm at 110-310 mm; linearity follows the accuracy curve
• Measuring range: 35-310 mm
• Output: analog 0-10 V, 2.5 kΩ min. load; response 0.5...2560 ms depending on measurement rate and averaging
• Supply: 12-30 V DC, < 675 mW
• Housing: flush mount, 316L stainless steel, PMMA lens cover; visible red Class 1 laser 655 nm
• Environment: IP67, IP68, IP69K, -10...+50 °C
• Connection: integral M12 male connector, 5-pin

The housing resists the acidic and caustic cleaning agents used in sanitation and is ECOLAB certified. Allow 10 minutes of warm-up for best accuracy.

Shock tested to MIL-STD-202G, method 213B (100 g); vibration to method 201A. UL and CE approved.

T18-2VPRL-9M is a Banner T18-2 series opposed-mode receiver, used with a T18-2 emitter. The right-angle 18 mm threaded housing has epoxy-encapsulated electronics and food-grade plastics, for wet and washdown areas.

• Sensing range: 25 m with a T18-2 emitter
• Output: complementary PNP (NO and NC), 100 mA total up to +55 °C; response 1.5 ms ON / 1 ms OFF
• Supply: 10-30 V DC (10-24 V DC above +55 °C), < 16 mA
• Housing: right-angle, 18 mm thread, PBT polyester, PMMA window
• Environment: IP67, IP68, IP69K, -40...+70 °C; ECOLAB chemical compatibility
• Connection: 9 m PVC cable

Vibration per MIL-STD-202G method 201A, shock per method 213B (75 g operating).

T18-2NAEL-9M is a Banner T18-2 series opposed-mode emitter with visible red light, used with a T18-2 receiver. The right-angle 18 mm threaded housing has epoxy-encapsulated electronics and food-grade plastics, for wet and washdown areas.

• Sensing range: 25 m with a T18-2 receiver
• Light source: visible red LED
• Supply: 10-30 V DC (10-24 V DC above +55 °C), < 16 mA
• Housing: right-angle, 18 mm thread, PBT polyester, PMMA window
• Environment: IP67, IP68, IP69K, -40...+70 °C; ECOLAB chemical compatibility
• Connection: 9 m PVC cable

Vibration per MIL-STD-202G method 201A, shock per method 213B (75 g operating).

RKC4.4T-P7X2-5/TXL is a TURCK connection cable with a straight M12 female connector (4-pin) on one end and open cores on the other. The connector has two built-in LED indicators: green shows the supply, yellow the PNP signal on pin 4.

• Connector: M12 x 1 female, straight, A-coded, 4-pin, gold-plated brass (CuZn) contacts
• Cable: 5 m, PUR, black, Ø 4.5 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 30 V DC, more than 100 mating cycles
• Housing: translucent TPU, nickel-plated brass coupling nut, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 5 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The PUR jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.

IM12-AI01-1I-2IU-HPR/24VDC/CC is a 1-channel TURCK isolating transducer for HART 2-wire transmitters. The 4...20 mA input is passed 1:1 to two isolated outputs (splitter), and HART communication runs bidirectionally through output O1.

• Channels: 1 input, 4...20 mA, transmitter supply 17 V / 20 mA
• Outputs: 2 x 4...20 mA (source or sink) or 1...5 V; HART on O1 only
• Accuracy: ≤0.05 % of full scale
• Supply: 10...30 V DC via terminals or Power bridge, ≤3.8 W
• Housing: polycarbonate/ABS, 120 x 12.5 x 128 mm, DIN rail (NS35), removable spring-type terminals
• Environment: IP20, -25...+70 °C

Used where one transmitter signal from a hazardous area is needed by two systems, for example a control system and a separate safety system. Wire break (< 3.5 mA) and short circuit (> 22 mA) are passed to the outputs as < 3.5 mA or < 0.875 V. The Power bridge also carries a collective fault signal; its connector is included.

Approvals: ATEX, cULus; for use in ATEX Zone 2. SIL 2.

QS18VP6AF300Q5 is a Banner QS18 series photo sensor with adjustable background suppression and a visible red 640 nm LED beam. Objects up to the set cutoff are detected regardless of colour, while anything beyond it is ignored.

• Sensing range: cutoff adjustable 30-300 mm
• Output: complementary PNP, Light Operate and Dark Operate
• Response: 2.5 ms; repeatability 250 µs
• Supply: 10-30 V DC
• Housing: ABS, acrylic lens
• Environment: IP67, -20...+55 °C
• Connection: 150 mm PVC cable with M12 4-pin male connector

The cutoff distance is set with a mechanical adjustment screw. A crosstalk algorithm lets two sensors work close to each other. A green LED indicator shows power; the amber one shows light sensed and flashes at a marginal condition.

BRT-THG-2-100 is a Banner self-adhesive retroreflective tape, 50 mm wide and 2.5 m long, used as a target for photo sensors in retroreflective mode. It is not recommended for polarized retroreflective sensors.

• Size: 50 mm wide, 2.5 m long
• Reflectivity factor: 0.7
• Temperature: max +60 °C

For full adhesion the surface must be clean.

RKS4.4T-1-RSS4.4T/TXL is a TURCK shielded connection cable with a straight M12 female connector on one end and a straight M12 male connector on the other (4-pin). The cable shield is connected to the coupling nut.

• Connectors: M12 x 1, female, straight, A-coded / M12 x 1, male, straight, A-coded; 4-pin, gold-plated brass (CuZn) contacts
• Cable: 1 m, PUR, black, Ø 5.3 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Shield: aluminium foil and tinned copper wire
• Ratings: 4 A, 250 V, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nuts, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 2 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The PUR jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.

TL50GRALSQ is a Banner TL50 series 50 mm LED tower light with 2 colour segments: green, red, from the bottom up, topped by a sealed audible alarm. Each colour has its own input wire and the inputs are bimodal, so the tower can be driven from either PNP or NPN controller outputs.

• Colours: green 528 nm, red 625 nm
• Audible: continuous tone, 2.9 kHz, up to 94 dB at 1 m, adjustable down to 74 dB
• Inputs: bimodal (PNP or NPN), one per colour, response 10 ms
• Supply: 18-30 V DC or 24 V AC 50/60 Hz, up to 45 mA per colour, alarm 35 mA
• Housing: Ø50 x 183.2 mm, ABS base and covers, polycarbonate light segments, black, M30x1.5 base mount
• Environment: IP67, -20...+50 °C
• Connection: integral M12 male connector, 4-pin

The tower connects through a separately ordered 4-pin M12 female cordset. Audible intensity is adjusted by rotating the front cover of the alarm.

Vibration tested to IEC 60068-2-6, shock to IEC 60068-2-27 (30 g, 11 ms).

SI-RFPT-LP5 is a Banner SI-RF series non-contact RFID safety switch for monitoring guard doors and covers, used with the SI-RF-A actuator. It has two OSSD safety outputs and one PNP auxiliary output, and resets automatically when the guard closes.

• Safety: up to PL e, Category 4 (EN ISO 13849-1), SIL CL 3 (EN 62061), PFHd 6 x 10⁻⁹ 1/h
• Switching distance: on at 10 mm, off at 25 mm, typical 13 mm; coding level low (accepts any SI-RF-A actuator)
• Outputs: 2 OSSD PNP, 100 mA each; 1 PNP auxiliary, 10 mA; switch-off delay 100 ms
• Supply: 24 V DC (+25 %/-20 %), no-load current ≤ 50 mA
• Housing: 36 x 26 x 15 mm, PA66/PA6, red, 2 x M4 mounting holes
• Environment: IP69, -25...+70 °C
• Connection: 250 mm PUR cable with M12 male connector, 5-pin

The switch works with the SI-RF-A or SI-RF-A2 actuator and a safety controller or relay that evaluates the OSSD outputs, all ordered separately. Low coding means any SI-RF actuator is accepted, so the switch suits guards where tamper resistance is handled by mounting.

Meets EN 60947-5-3, EN ISO 13849-1, EN 62061 and EN 60204-1. TÜV Nord and cCSAus approved; CE.

T18-2VPLP-Q8 is a Banner T18-2 series polarized retroreflective photo sensor with a 6 m range to a BRT-84 reflector, in a right-angle 18 mm housing for washdown areas. The polarizing filter rejects light returned by shiny objects, so they break the beam instead of acting as a reflector.

• Sensing range: 6 m with a BRT-84 reflector
• Output: complementary PNP, Light Operate (black wire) and Dark Operate (white wire), 100 mA total (50 mA above +55 °C)
• Response: 1.5 ms ON, 0.75 ms OFF; repeatability 100 µs
• Supply: 10-30 V DC (10-24 V DC above +55 °C), < 16 mA
• Housing: right-angle, M18x1 thread, PBT polyester, PMMA window, epoxy-encapsulated electronics
• Environment: IP67, IP68, IP69K, -40...+70 °C
• Connection: integral M12 4-pin male connector

Needs a reflector, ordered separately. There is no sensitivity adjustment. A green LED shows power and flashes at a marginal signal; the amber LED shows that the black-wire output is on.

ECOLAB certified chemical compatibility. Vibration tested to MIL-STD-202G, method 201A; shock to method 213B (75 g operating).

Q456E is the emitter of a Banner Q45 series opposed-mode photo sensor pair. Its infrared 880 nm beam reaches a Q45BB6 receiver up to 60 m away, with enough excess gain for dirty or dusty areas; the emitter itself has no output.

• Sensing range: 60 m with a Q45BB6 receiver
• Output: none (emitter)
• Supply: 10-30 V DC
• Housing: rugged rectangular, thermoplastic, acrylic lens, 30 mm threaded mounting hub
• Environment: IP67, NEMA 6P, -40...+70 °C
• Connection: 2 m PVC cable, 2 wires

Needs a Q45BB6 receiver, ordered separately. The housing is designed to withstand 1200 psi washdown. CE approved.

WKC4.4T-2-RSC4.4T/TXL is a TURCK extension cable with an angled M12 female connector on one end and a straight M12 male connector on the other (4-pin).

• Connectors: M12 x 1 female, angled / M12 x 1 male, straight; A-coded, 4-pin, gold-plated brass (CuZn) contacts
• Cable: 2 m, PUR, black, Ø 4.5 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 250 V, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nuts, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 5 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The PUR jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.

QS18VN6D is a Banner QS18 series diffuse photo sensor with an infrared beam, in a compact housing with an M18 threaded nose. It detects objects by the light they reflect back, up to 450 mm from the sensor.

• Sensing range: 450 mm, adjustable
• Output: complementary NPN, Light Operate and Dark Operate
• Response: 0.6 ms; repeatability 150 µs
• Supply: 10-30 V DC
• Housing: rectangular with M18 threaded nose, ABS, acrylic lens
• Environment: IP67, NEMA 6, -20...+70 °C
• Connection: 2 m PVC cable, 4 wires

Sensitivity is set with a potentiometer. The M18 nose fits a standard 18 mm mounting hole. UL and CE approved.

RSSD-RJ45S-4422-3M is a TURCK Industrial Ethernet cable with a straight M12 male connector on one end and a straight RJ45 male connector on the other (4-pin). The 4-wire CAT 5e cable carries 100 Mbit/s Ethernet and PROFINET.

• Connectors: M12 x 1 male, straight, D-coded / RJ45 male, straight; 4-pin
• Cable: 3 m, PUR, green, Ø 6.5 mm, 4 x 0.32 mm², core colours WH, YE, BU, OG, overall shield of aluminium foil and tinned copper braid
• Ratings: 1.5 A, 42 V DC; CAT 5e, impedance 100 Ω, capacitance 50 pF/m
• Housing: TPU, nickel-plated brass coupling nut
• Environment: M12 IP67 (only when screwed in), RJ45 IP20; -40...+80°C fixed, -30...+80°C mobile
• Drag chain: at least 5 million bending cycles, bending radius ≥15 x Ø, torsion ±180°/m

The green PUR jacket is halogen free (IEC 60754), oil resistant (IEC 60811-2-1) and flame retardant (IEC 60332-1-2); the cable is RoHS compliant and PNO compliant for PROFINET. Approval: UL Listed.

PKG4M-20/TXL is a TURCK connection cable with a straight M8 female connector (4-pin) on one end and open cores on the other.

• Connector: M8 x 1 female, straight, 4-pin, gold-plated brass (CuZn) contacts
• Cable: 20 m, PUR, black, Ø 4.5 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 50 V AC/60 V DC, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nut, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 5 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The PUR jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.