The BL20-PG-EN-V3 is a TURCK BL20 series programmable gateway with an integrated CODESYS V3 PLC environment. It works as the head module of a BL20 station and, at the same time, as a controller that processes I/O data and communicates with higher system levels.

• Configuration: CODESYS V3 PLC environment, OPC UA server/client
• Communication: Modbus TCP, EtherNet/IP, PROFINET, integrated 10/100 Mbps switch (switched or dual-MAC mode), 2x RJ45
• Power: 24 VDC (18...30 VDC), module bus current ≤200 mA, field supply current up to 8 A, system supply current up to 1.3 A
• Indication: LEDs for PLC status, supply and fault signalling
• Environment: IP20, 0...+55°C

The gateway replaces a separate PLC in the control cabinet, since it processes the BL20 station's I/O data itself according to a CODESYS V3 program and simultaneously connects the station to the plant Ethernet network, including TURCK Cloud IIoT connectivity. The station additionally requires matching BL20-E series I/O modules, ordered separately.

The BL20-E-2CNT-2PWM is a TURCK BL20-E series economy module with 2 counter/encoder input channels and 2 PWM outputs. Electronics and connection technology are combined in one housing, so no separate base module is needed.

• Inputs: 2 counter/encoder channels up to 200 kHz, thresholds parametrizable 0...1 V/0...4.5 V (low) and 2.5...30 V/7.5...30 V (high)
• Outputs: 2 PWM outputs 20 kHz / 0.5 A, 2 digital outputs 20 kHz / 0.5 A, output voltage 24 VDC
• Power: 24 VDC (18...30 VDC), field supply current ≈20 mA, module bus current ≈50 mA
• Connection: push-in terminals
• Environment: IP20, 0...+55°C

The module operates as part of a BL20-E station together with a BL20-E-GW gateway and other BL20-E modules, and is suited for reading encoders and driving motors or valves with a PWM signal.

Complies with cULus requirements.

The BL20-2AI-I(0/4...20MA) is a TURCK BL20 series electronic module with 2 analogue current inputs. The module mounts on a separate BL20 base, and the field signal is galvanically isolated from the module bus via an optocoupler.

• Inputs: 2 analogue current inputs, signal 0/4...20 mA
• Accuracy: input resistance <0.125 kΩ, maximum input current 50 mA
• Power: 24 VDC, field supply current ≤12 mA, module bus current ≤35 mA
• Connection: screw or tension-spring terminals (depending on the base)
• Environment: IP20, 0...+55°C

The module requires a separately ordered BL20 base (S3 or S4 series, with screw or tension-spring terminals) — it cannot be used without one. The electronics can be replaced without disconnecting the field wiring, since the connections stay on the base.

Complies with cULus requirements.

GSM datalogger is designed to record 3 current inputs and 1 binary input. In case of exceeded set limits, SMS and JSON messages can be sent via GPRS data connection. Measured values can be sent to the internet storage COMET Cloud, which is a complete monitoring, alarm and analysis system.

It is also possible to set the regular sending of JSON messages to COMET Database, the sending interval is adjustable. Alarms are also indicated locally by LED, LCD and acoustically by built-in beeper.

The recording is performed in a non-volatile electronic memory. The data can be transferred to a PC via included USB-C cable.

GSM recorder includes Traceable calibration certificate with declared metrological traceability of etalons is based on requirements of EN ISO/IEC 17025 standard.

B-TL70Z-Q5 is the AC base module of the Banner TL70 modular tower light, for towers of one to four modules. Each module is switched by its own 100...240 V AC hot wire through the base connector.

• Supply: 100...240 V AC, 50/60 Hz; max. 50 mA per module at 230 V AC
• Modules: 1-4 light or audible modules, position set with DIP switches in each module
• Mode: steady or flashing at 1.5 Hz or 3 Hz, set per module
• Housing: polycarbonate, internal 1/2-14 NPSM mounting thread
• Environment: IP65, -40...+50 °C
• Connection: integral 1/2"-20UNF male quick-disconnect connector, 5 pins

The base takes the same light and audible modules as the DC TL70, so the tower wires straight to 230 V AC control outputs. The base tolerates up to 500 µA leakage current; solid-state PLC outputs often exceed 1 mA, which keeps a module lit in the off state. In that case use relay outputs or fit a shunt resistor between the neutral wire and the hot wire of each channel.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

DX80G2M6S-PM2 is the gateway of a Banner Sure Cross Performance PM2 pair, with four discrete and two 0-20 mA analog channels in each direction. The I/O mapping to the PM2 node is selected in its LCD menu, and an RS-485 port gives Modbus RTU access.

• Inputs and outputs: 4 discrete inputs, NPN/PNP selectable, 3 mA at 30 V DC; 4 PNP discrete outputs, 100 mA; 2 analog inputs 0-20 mA, 12-bit, ±0.2 % FS; 2 analog outputs 0-20 mA, 12-bit, ±0.1 % FS
• Radio: 2.4 GHz FHSS, 65 mW conducted, EIRP < 100 mW with the supplied antenna, RP-SMA antenna connector
• Communication: RS-485 2-wire half duplex, Modbus RTU, 9.6k, 19.2k (default) or 38.4k baud
• Supply: 10...30 V DC (outside the USA 12...24 V DC ±10 %)
• Housing: polycarbonate, two 1/2" NPT cable entries, two buttons, 6-character LCD, 0.26 kg
• Environment: IP67, NEMA 6; -40...+85 °C (LCD -20...+80 °C), 95 % RH non-condensing

The gateway works paired with a 2.4 GHz PM2 node, ordered separately; it ships with a 2 dBd omni antenna. On link loss the discrete outputs switch OFF.

CE and UKCA (2.4 GHz models), RED 2014/53/EU; FCC ID UE3SX243, IC 7044A-SX243.

DX80N2X6S-PM2 is the node of a Banner Sure Cross Performance PM2 pair, with four discrete and two 0-20 mA analog channels in each direction. Its I/O mapping to the PM2 gateway is selected in the gateway's LCD menu.

• Inputs and outputs: 4 discrete inputs, NPN/PNP selectable, 3 mA at 30 V DC; 4 PNP discrete outputs, 100 mA; 2 analog inputs 0-20 mA, 12-bit, ±0.2 % FS; 2 analog outputs 0-20 mA, 12-bit, ±0.1 % FS
• Radio: 2.4 GHz FHSS, 65 mW conducted, EIRP < 100 mW with the supplied antenna, RP-SMA antenna connector
• Configuration: DIP switches for NPN/PNP input type, mapping from the gateway menu
• Supply: 10...30 V DC (outside the USA 12...24 V DC ±10 %)
• Housing: polycarbonate, two 1/2" NPT cable entries, two buttons, 6-character LCD, 0.26 kg
• Environment: IP67, NEMA 6; -40...+85 °C (LCD -20...+80 °C), 95 % RH non-condensing

The node works only paired with a 2.4 GHz PM2 gateway, ordered separately. Discrete inputs report on change of state; analog inputs report every second or on a 1 % change.

CE and UKCA (2.4 GHz models), RED 2014/53/EU; FCC ID UE3SX243, IC 7044A-SX243.

The BL20-PG-EN-V3-WV is a variant of the BL20-PG-EN-V3 programmable gateway with a CODESYS WebVisu license included. The gateway works as the head module and controller of a BL20 station, and WebVisu lets a process visualisation be opened directly in a browser without extra SCADA software.

• Configuration: CODESYS V3 PLC environment with WebVisu license included, OPC UA server/client
• Communication: Modbus TCP, EtherNet/IP, PROFINET, integrated 10/100 Mbps switch (switched or dual-MAC mode), 2x RJ45
• Power: 24 VDC (18...30 VDC), module bus current ≤200 mA, field supply current up to 8 A, system supply current up to 1.3 A
• Indication: LEDs for PLC status, supply and fault signalling
• Environment: IP20, 0...+55°C

The gateway fits where an operator needs to view or control the BL20 station's process from any device with a browser, without installing a separate visualisation server. The station additionally requires matching BL20-E series I/O modules, ordered separately.

Complies with FM ATEX, IECEx and FM Class I Div. 2 (US and Canada) requirements, and carries an EU Declaration of Conformity.

K50L2RGB7ALSQ is a Banner K50 Pro series 50 mm RGB dome indicator with a sealed loud audible alarm. Combinations of three inputs give seven colors, and the fourth, gray wire switches the audible.

• Colors: green, red, yellow, blue, white, cyan, magenta
• Audible: continuous tone 2.9 kHz, 94 dB at 1 m
• Inputs: bimodal PNP/NPN, response time 250 ms
• Supply: 10...30 V DC, 220 mA at 10 V, 115 mA at 24 V
• Housing: polycarbonate, M30x1.5 threaded base, 50 x 73 mm
• Environment: IP67, UL 4X and 13, -40...+50 °C
• Connection: integral 5-pin M12 male connector

Whether the inputs act as PNP or NPN depends only on the wiring. Colors and animations can be reprogrammed with Banner Pro Editor software and a Pro Converter cable.

CE and UL compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

TX705-P3CV01 is a 5" touch display from the TURCK TX700 series with a built-in CODESYS V3 PLC, TARGET and WEB VISU visualisation. The PLC program and the screens are built in CODESYS V3 and loaded into the device over Ethernet.

• Display: 5" TFT, 800 x 480 (WVGA), 16:9, 64K colours, 300 cd/m², capacitive glass front, dimmable to 0 %
• Communication: 2 x RJ45 Ethernet 10/100 Mbit, 1 x RS232/RS485/RS422, 1 x USB host, SD card slot
• Expansion: 1 slot for up to 2 plug-in modules (I/O, CANopen, PROFIBUS DP, RS485, RS232, LTE/Wi-Fi)
• PLC: CODESYS V3.5.12.10, IEC 61131-3 (IL, LD, FBD, SFC, ST), 20000 kB program memory, 63 kB retain memory; ARM Cortex A8, 1 GHz, 512 MB RAM, 4 GB Flash, battery-backed clock
• Supply: 24 VDC (10...32 VDC), max. 0.6 A
• Housing: metal, front 147 x 107 x 52 mm, cut-out 136 x 96 mm, mounting depth 52+8 mm
• Environment: IP66 front, IP20 rear, NEMA 12/4X; -20...+60 °C, 5...85 % RH non-condensing

Built into a cabinet door or control desk. Mounting brackets and the power connector come in the 5" TX700 mounting kit, available as an accessory; I/O and fieldbus modules plug into the expansion slots and are ordered separately.

Q20NAF200 is a Banner Q20 series photo sensor with adjustable background suppression and a visible red 640 nm beam. Objects up to the set cutoff are detected regardless of colour, while anything beyond it is ignored.

• Sensing range: adjustable cutoff 30...200 mm
• Output: complementary NPN, Light Operate and Dark Operate, 50 mA total
• Response: 1.7 ms ON, 1.1 ms OFF; repeatability 130 µs
• Supply: 10-30 V DC, < 300 mW
• Housing: ABS front, copolyamide rear, PMMA lenses, 3 mm mounting holes at 25.4 mm spacing
• Environment: IP67, -20...+60 °C
• Connection: 2 m PVC cable, 4 wires

The cutoff is set with a single-turn potentiometer. A green LED indicator shows power; the amber one shows light sensed and flashes at a marginal sensing condition. Two sensors can be mounted close together without crosstalk.

PKG4M-5/TXG is a TURCK connection cable with a straight M8 female connector (4-pin) on one end and open cores on the other. The PUR jacket is rated for moving installation, including drag chains.

• Connector: M8 x 1, female, straight, 4-pin, gold-plated brass (CuZn) contacts
• Cable: 5 m, PUR, grey, Ø 4.5 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 50 VAC / 60 VDC, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nut, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 5 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.

RKC4.4T-0.5-RSC4.4T/TXL is a TURCK extension cable with a straight M12 female connector on one end and a straight M12 male connector on the other (4-pin). The PUR jacket is rated for moving installation, including drag chains.

• Connectors: M12 x 1 female and M12 x 1 male, both straight, A-coded, 4-pin, gold-plated brass (CuZn) contacts
• Cable: 0.5 m, PUR, black, Ø 4.5 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 250 V, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nut, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 5 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.

S18-2VNLPC-Q8 is a Banner S18-2 series polarized retroreflective photo sensor in an 18 mm plastic barrel, with a 6 m range to a BRT-84 reflector. The polarizing filter rejects light returned by shiny objects, so they break the beam instead of acting as a reflector.

• Sensing range: 6 m with a BRT-84 reflector
• Output: complementary NPN, Light Operate (black) and Dark Operate (white), 100 mA total
• Response: 1.5 ms ON, 0.75 ms OFF; repeatability 100 µs
• Supply: 10-30 V DC (10-24 V DC above +55 °C), 16 mA
• Housing: ABS, PMMA window, M18x1 threaded barrel, PBT nuts included
• Environment: IP67, -40...+70 °C
• Connection: integral M12 4-pin male connector

Needs a reflector, ordered separately. Sensitivity is set with a single-turn potentiometer. A green LED shows power and flashes at a marginal signal; the amber LED shows that the black-wire (Light Operate) output is on.

Vibration tested to MIL-STD-202F, method 201A; shock to method 213B (75 g operating).

SMBQS12PD is a Banner right-angle bracket that holds the sensor by its threaded nose through a 13 mm hole.

• Sensor hole: Ø13.0 mm
• Mounting: Ø3.5 mm and 3.5 x 10.6 mm slot, 14.0 mm hole centre spacing
• Material: 16-gauge 300 series stainless steel

SA-M30 is a Banner cover that hides the outer M30 thread on a light's base.

• Fits: devices with an M30 base, Banner lists TL70 tower lights and the K90 series
• Material: black polycarbonate
• Included: mounting hardware

SOP-E12-150A is a Banner 150 mm stand-off pipe for mounting an indicator, tower light or sensor elevated above the mounting surface.

• Length: 150 mm
• Thread: ½" NPT at both ends (NPSM/DN15)
• Material: black anodised aluminium

The lower end of the pipe needs a mounting base and the upper end an adapter for the device's base.

SA-F12-3 is a Banner elevated mount system base that fixes a ½" stand-off pipe to a flat surface with three screws.

• Connection: ½" NPSM/DN15 pipe
• Dimensions: Ø70 mm, 3 mounting holes
• Material: black polycarbonate
• Included: M4 mounting hardware and nitrile blend gasket

SA-M22E12 is a Banner adapter that connects a light's 22 mm base to a ½" stand-off pipe for elevated mounting. Banner specifies it for TL30 tower lights.

• Connection: 22 mm device base - ½" NPSM/DN15 pipe
• Material: black polycarbonate
• Mounting hardware: not included

SMBWLS28RA is a Banner replacement end bracket kit for WLS28 LED lights.

• Included: 2 end brackets and 4 screws
• Material: 1.8 mm (14-gauge) cold-rolled steel
• Finish: zinc plate with clear chromate