QT50ULBQ6 is a Banner U-GAGE QT50ULB long-range ultrasonic sensor with an analog output scaled across a taught window. The output type, slope, response speed and temperature compensation are set with eight DIP switches under a sealed cover.

• Accuracy: linearity ±0.2 % of span (200...8000 mm), ±0.1 % of span (500...8000 mm); resolution 1 mm; temperature effect 0.02 % of distance/°C compensated
• Measuring range: 200 mm...8 m, 75 kHz; minimum window 20 mm
• Output: analog 0-10 V or 4-20 mA, selected by DIP switch; response 100...2300 ms
• Supply: 10...30 V DC, 100 mA at 10 V
• Housing: ABS/polycarbonate
• Environment: IP67, NEMA 6P, -20...+70 °C
• Connection: integral M12 5-pin male

The near and far limits are taught with push buttons or the remote wire and can be set independently; objects inside 200 mm may cause a false reading.

Vibration per MIL-STD-202F method 201A, shock per IEC 947-5-2 (30 g, 11 ms).

SMB30A is a Banner right-angle bracket for sensors with a 30 mm housing. The curved slot lets the sensor be turned before the screws are tightened.

• Sensor hole: Ø30.5 mm
• Mounting: M6 (¼") hardware, 40 mm hole centre spacing
• Material: 12-gauge stainless steel

UR18.EB0.2-GP2J.9SF is the receiver of a Baumer UR18 series ultrasonic through-beam sensor, in an M18 stainless steel housing with an operating range up to 2000 mm. The manufacturer recommends it for double sheet detection.

• Accuracy: repeatability 3 mm; hysteresis typ. 5 % Sde; temperature drift < 2 % Sde; minimum object size > 4 cm² at 50 mm
• Operating range: 0...2000 mm; response time < 9 ms; sonic frequency 200 kHz
• Outputs: push-pull (works as PNP or NPN), up to 100 mA; IO-Link V1.1, COM 2 (38.4 kBaud), cycle time ≥ 3 ms, port type Class A, also transmits excess gain
• Supply: 12...30 V DC, consumption up to 25 mA; short-circuit and reverse-polarity protected
• Housing: M18 threaded cylinder, stainless steel (V2A) / TR90, PEEK-coated sensor face, 64 mm long
• Environment: IP69 (housing), IP67 (connection), operating temperature -25...+65 °C
• Connection: M12 connector, 5-pin

Works only as a pair with the UR18.TB0.2-ZZZZ.9SF emitter, which is ordered separately. The switching threshold is set by qTeach, Line-Teach or over IO-Link, which also configures output logic, time filters and the counter.

UR18.TB0.2-ZZZZ.9SF is the emitter of a Baumer UR18 series ultrasonic through-beam sensor, in an M18 stainless steel housing with an operating range up to 2000 mm. The emitter has no switching output.

• Operating range: 0...2000 mm; sonic frequency 200 kHz
• Supply: 12...30 V DC, typical consumption 25 mA; short-circuit and reverse-polarity protected
• Housing: M18 threaded cylinder, stainless steel (V2A) / TR90, PEEK-coated sensor face, 64 mm long
• Environment: IP69 (housing), IP67 (connection), operating temperature -25...+65 °C
• Connection: M12 connector, 5-pin; green LED shows power

Works only as a pair with the UR18.EB0.2-GP2J.9SF receiver, which is ordered separately; all settings and the output are on the receiver.

UWG18-5.0 is a Banner wave guide that threads onto the 18 mm barrel of an S18U or QS18U ultrasonic sensor and focuses the beam through a 5.0 mm bore. It lets the sensor reach into small openings and detect sheet metal edges.

• Fits: Banner S18U and QS18U ultrasonic sensors
• Bore: inside Ø 5.0 mm, outside Ø 7.0 mm
• Material: acetal
• Included: slim threaded plastic nut and gasket

Tighten the wave guide until the sensor face sits on the gasket and the bevel faces down, so debris does not collect in the opening. In high-vibration positions a little thread-locker is recommended.

PRO-KIT is a Banner kit for configuring Pro series lights and selected sensors from a PC with the Pro Editor software. It is needed for initial configuration only, not for the device's operation in the machine.

• Included: converter cable, splitter and power supply
• Software: Banner Pro Editor
• Fits: Banner Pro series lights and selected sensors

CE and UKCA compliant.

U500.PA0.2-GP1J.72F is a Baumer U500 series ultrasonic proximity sensor with a 20...1000 mm operating range, a push-pull switching output and an IO-Link interface. A multiplex version lets several sensors run side by side without mutual interference.

• Accuracy: repeatability 0.5 mm; hysteresis typ. 4 % Sde; temperature drift < 2 % Sde; power-up drift compensated after 15 min
• Sensing distance: 20...1000 mm; response time < 40 ms; sonic frequency 200 kHz
• Outputs: push-pull (works as PNP or NPN), up to 100 mA; IO-Link V1.1, COM 2 (38.4 kBaud), cycle time ≥ 12 ms, port type Class A, also transmits distance
• Supply: 12...30 V DC, typical consumption 35 mA; short-circuit and reverse-polarity protected
• Housing: rectangular, ASA/PMMA plastic, PEEK-coated sensor face, 18 x 45 x 32 mm
• Environment: IP67, operating temperature -25...+65 °C
• Connection: M12 connector, 5-pin

Suited to presence and level detection up to 1 m regardless of colour and transparency. The switching point is set by qTeach, Line-Teach or over IO-Link, which also configures output logic, time filters, beam forming and the function of pin 5.

T30UIPAQ is a Banner T30U series ultrasonic sensor with a 4-20 mA analog output and a PNP discrete output. Both can be taught together or separately, and the analog slope is set by the order in which the limits are taught.

• Accuracy: analog linearity ±0.5 % of full scale; resolution and repeatability ±0.25 % of distance; 10 x 10 cm aluminium target, 25 °C
• Measuring range: 150 mm...1 m, 228 kHz; minimum window 10 mm
• Outputs: analog 4-20 mA; discrete PNP, 100 mA; response 48 ms
• Supply: 12...24 V DC, 90 mA
• Housing: M30 thread, reinforced thermoplastic polyester (PBT)
• Environment: IP67, -20...+70 °C
• Connection: integral M12 5-pin male

Window limits are taught with the push buttons on the sensor or through the remote teach wire. Objects closer than 150 mm can cause a false response.

Vibration per MIL-STD-202F method 201A, shock per IEC 60947-5-2 (30 g, 11 ms). CE and UKCA.

T30UXUBQ8 is a Banner T30UX series ultrasonic sensor with a 0-10 V analog output scaled across a taught window and built-in temperature compensation. Fast or slow response, output slope and push-button lock are set from the sensor.

• Accuracy: linearity 0.25 % of distance; resolution 0.1 % of distance (1 mm min.); temperature effect 0.02 % of distance/°C
• Measuring range: 200 mm...2 m, 174 kHz; minimum window 10 mm
• Output: analog 0-10 V, min. load 2.5 kΩ; response 92 ms or 222 ms
• Supply: 10...30 V DC, 40 mA; full 10 V output from 12 V DC
• Housing: M30 x 1.5 thread, PBT
• Environment: IP67, -40...+70 °C
• Connection: integral M12 4-pin male

On loss of signal the output drops to 0 V, which the controller can read as a fault.

UNDK 30U6103/S14 is a Baumer ultrasonic distance sensor in a rectangular housing with a 100...1000 mm measuring range and a 0...10 V analog output. The start and end of the range are taught with the teach-in button on the housing.

• Accuracy: repeatability < 0.5 mm; resolution < 0.3 mm; temperature drift < 2 % of distance to target
• Measuring range: 100...1000 mm, start and end point adjustable; response time < 80 ms; sonic frequency 240 kHz
• Output: analog 0...10 V / 10...0 V, up to 20 mA
• Supply: 15...30 V DC, consumption up to 35 mA; short-circuit and reverse-polarity protected
• Housing: polyester / die-cast zinc, 30 x 65 x 31 mm
• Environment: IP67, operating temperature -10...+60 °C
• Connection: M12 connector

Suited to level and distance measurement up to 1 m where a plain analog signal to a controller without a digital interface is needed. Yellow and red LEDs show the status, and the display flashes when a target is inside the range, which helps with alignment.

UNAM 12P8910/S14OD is a Baumer high-speed ultrasonic proximity sensor in an M12 threaded housing with a 0...40 mm operating range. Response and release time are below 1.3 ms, and the switching frequency reaches 225 Hz.

• Accuracy: repeatability < 0.5 mm; hysteresis typ. 4 % Sde; temperature drift < 0.18 % Sde/K
• Sensing distance: 0...40 mm, set by external teach-in (white wire); sonic frequency 380 kHz
• Output: PNP, NO/NC programmable, up to 200 mA; voltage drop < 2 V DC
• Supply: 12...30 V DC, consumption up to 35 mA; short-circuit and reverse-polarity protected
• Housing: M12 x 1 nickel-plated brass cylinder, 100 mm long
• Environment: IP67, operating temperature -10...+60 °C
• Connection: M12 connector

The short operating range and fast response suit detection of small objects in fast cycled motion, where an optical sensor fails on transparent or glossy surfaces. The switching point is taught by connecting the teach-in wire; the green LED flashes when a target is inside the range, which helps with alignment.

T30UDPAQ is a Banner T30U series ultrasonic proximity sensor with two PNP outputs, each with its own taught switching window. The outputs can be taught together or separately and set as identical, independent, overlapping or complementary windows.

• Accuracy: repeatability ±0.25 % of distance; hysteresis 2.5 mm; minimum window 10 mm
• Sensing range: 150 mm...1 m, 228 kHz
• Outputs: 2x PNP, 100 mA total; response 48 ms
• Supply: 12...24 V DC, 90 mA
• Housing: M30 thread, reinforced thermoplastic polyester (PBT)
• Environment: IP67, -20...+70 °C
• Connection: integral M12 5-pin male

Window limits are taught with the push buttons on the sensor or through the remote teach wire, with no potentiometers to adjust. Objects closer than 150 mm can cause a false response.

Vibration per MIL-STD-202F method 201A, shock per IEC 60947-5-2 (30 g, 11 ms). CE and UKCA.

S18UIAQ is a Banner U-GAGE S18U ultrasonic sensor in a straight M18 housing with a 4-20 mA output scaled across a taught window. Its 30 mm near limit lets it measure close to the sensor face, and temperature compensation is built in.

• Accuracy: linearity ±1 mm (2.5 ms) or ±0.5 mm (30 ms); resolution 1 mm or 0.5 mm; 50 x 50 mm aluminium target, 22 °C
• Measuring range: 30...300 mm, 300 kHz; minimum window 5 mm
• Output: analog 4-20 mA; response 2.5 ms or 30 ms, selected on the black wire
• Supply: 10...30 V DC, 40 mA typical at 25 V
• Housing: M18 straight, thermoplastic polyester
• Environment: IP67, NEMA 6P, -20...+60 °C
• Connection: integral M12 5-pin male

Window limits are taught with the push button or the remote wire.

Vibration per MIL-STD-202F method 201A, shock per IEC 60947-5-2 (30 g, 11 ms).

U500.DA5.2-UAMJ.72F is a Baumer U500 series ultrasonic distance sensor with a 20...1500 mm measuring range, a 0...10 V analog output and an IO-Link interface. It has two IO-Link channels (dual channel) and a multiplex version, so several sensors can run side by side without mutual interference.

• Accuracy: repeatability 0.5 mm; resolution < 0.3 mm; temperature drift < 2 % of object distance (> 50 mm); power-up drift compensated after 15 min
• Measuring range: 20...1500 mm, start and end point adjustable; response time < 70 ms; sonic frequency 200 kHz
• Outputs: analog 0...10 V / 10...0 V, up to 100 mA; IO-Link V1.1, COM 2 (38.4 kBaud), cycle time ≥ 12 ms, port type Class A, 48-bit process data (distance, 2 switching channels, quality, alarm, counter)
• Supply: 12...30 V DC, average consumption 35 mA; short-circuit and reverse-polarity protected
• Housing: rectangular, ASA/PMMA plastic, PEEK-coated sensor face, 18 x 45 x 32 mm
• Environment: IP67, operating temperature -25...+65 °C
• Connection: M12 connector, 5-pin

Suited to level measurement in tanks and distance measurement up to 1.5 m, where object colour, transparency or dust disturbs an optical measurement. The range is set by qTeach, Line-Teach or over IO-Link, which also configures filtering, the output characteristic, the sonic beam width and the function of pin 5.