IGYX 12N17B1/S14L is a Baumer inductive proximity sensor in an M12 barrel with a 4 mm nominal sensing distance and a NPN normally open (NO) output. The sensing face is flush mountable and the nickel-plated brass housing is 60 mm long.

• Sensing distance: 4 mm (Sn), assured 3.2 mm (Sa)
• Output: NPN, normally open (NO), 200 mA, with short-circuit and reverse-polarity protection
• Supply: 10...30 V DC, current consumption up to 15 mA with no load
• Housing: M12 thread, nickel-plated brass, PBT sensing face, 60 mm long, flush mountable
• Environment: IP 67, operating temperature -25...+75 °C
• Connection: M12 connector

The sensor is intended for presence and end-position monitoring of metal parts on conveyors, pneumatic cylinders and indexing mechanisms. Switching frequency is 1.5 kHz. Tightening torque on the M12 thread must not exceed 10 Nm, and the switching point drifts by up to ±10 % of Sr across the temperature range, which matters when the target sits close to the 4 mm limit.

Complies with the EMC requirements of EN 60947-5-2:2007.

IGYX 12P17B1/S14L is a Baumer inductive proximity sensor in an M12 barrel with a 4 mm nominal sensing distance and a PNP normally open (NO) output. The sensing face is flush mountable and the nickel-plated brass housing is 60 mm long.

• Sensing distance: 4 mm (Sn), assured 3.2 mm (Sa)
• Output: PNP, normally open (NO), <200 mA, with short-circuit and reverse-polarity protection
• Supply: 10...30 V DC, current consumption up to 15 mA with no load
• Housing: M12 thread, nickel-plated brass, PBT sensing face, 60 mm long, flush mountable
• Environment: IP 67, operating temperature -25...+75 °C
• Connection: M12 connector

The sensor is intended for presence and end-position monitoring of metal parts on conveyors, pneumatic cylinders and indexing mechanisms. Switching frequency is <1.5 kHz. Tightening torque on the M12 thread must not exceed 10 Nm, and the switching point drifts by up to ±10 % of Sr across the temperature range, which matters when the target sits close to the 4 mm limit.

Complies with the EMC requirements of EN 60947-5-2:2007.

IM12-DI01-2S-2T-0/24VDC is a 2-channel TURCK isolating switching amplifier in a 12.5 mm housing with two potential-free transistor outputs up to 10 kHz. It runs either as two separate channels or with channel 1 doubled onto both outputs.

• Channels: 2 inputs for NAMUR sensors (EN 60947-5-6) or potential-free contacts
• Outputs: 2 potential-free, short-circuit-proof transistors, ≤30 V DC, 0.1 A, ≤10 kHz
• Supply: 10...30 V DC, ≤0.8 W
• Housing: polycarbonate/ABS, 120 x 12.5 x 117 mm, DIN rail (NS35)
• Connection: removable screw terminals, 0.2...2.5 mm²
• Environment: IP20, -25...+70 °C

DIP switches on the front set the output mode, input circuit monitoring and the operating mode. An input fault makes the red LED flash according to NE44 and blocks the transistor of that channel. Mechanical contacts need either monitoring switched off or the resistor wiring shown in the datasheet.

Approvals: ATEX, cULus; for use in ATEX Zone 2. Usable in safety circuits up to SIL 2 (IEC 61508).

IM12-TI02-2TCURTDR-2I-C0/24VDC is a 2-channel TURCK temperature measuring amplifier for thermocouples, RTDs, resistors and mV signals. It converts the inputs to galvanically isolated 0/4...20 mA outputs; cold junction compensation can be internal, external or a fixed value.

• Inputs: 2 x thermocouple (IEC 60584, DIN 43710), -150...+150 mV, RTD (IEC 60751, DIN 43760) or 0...5 kΩ, 2- or 3-wire
• Outputs: 2 x 0/4...20 mA, source or sink (15...28 V); inputs assignable as E1, E2, E1-E2 or E2-E1
• Configuration: PC via FDT and IODD
• Supply: 10...30 V DC, ≤2.7 W
• Housing: polycarbonate/ABS, 120 x 12.5 x 117 mm, DIN rail (NS35), removable screw terminals
• Environment: IP20, -25...+70 °C

Used where a mix of thermocouples and RTDs from a hazardous area has to reach the control system as current signals. With a 3-wire RTD connection, the lead resistances must be equal. Input faults are indicated according to NE44, and a PC connection is needed for parameterisation.

Approvals: ATEX, cULus; for use in ATEX Zone 2. SIL 2.

DMP 331 is a stainless steel pressure transmitter for universal industrial applications, provided the medium is compatible with stainless steel 1.4404 (316L) or 1.4435 (316L). Various elastomer seals and a helium-tested welded version are available. Its modular design allows combining different sensor elements, electronic modules, and electrical/mechanical connections, resulting in a wide range of configurations that meet almost all industrial requirements.

Level sensor LMP 331 0-10m H2O Art: 430-1001-1-1-1-1-100-3-000