AFI4-5D30.4006.1300 is a Baumer CombiLyz inductive conductivity sensor with display and bottom process connection. It passes conductivity and temperature on as two separate 4...20 mA signals, and over IO-Link 1.1 the same readings and the sensor settings are also available digitally.

• Measuring range: 14 selectable ranges, 0...500 µS/cm to 0...1000 mS/cm; temperature -20...150 °C
• Output: 2 x 4...20 mA (conductivity, temperature), 2 solid-state relays, IO-Link 1.1
• Supply: 15...35 V DC (18...30 V DC with IO-Link)
• Housing: FlexHousing Ø80 mm, AISI 304, G 1 A hygienic connection, PEEK Natura probe L=60 mm
• Environment: IP67 / IP69K; process -20...140 °C (up to 150 °C for less than 1 h), up to 25 bar
• Connection: 1 x M12-A, 5-pin + 1 x M12-A, 8-pin, stainless steel AISI 304

Used for concentration control of CIP solutions and for phase separation between product, water and cleaning solution in dairy, brewery and beverage lines. The minimum measurable conductivity is 50 µS/cm, so the sensor does not suit demineralised or purified water.

cULus listed (E491206); wetted parts in PEEK Natura comply with FDA 21 CFR 177.2415.

WKC4.5T-1-RSC4.5T/TXL is a TURCK extension cable with an angled M12 female connector on one end and a straight M12 male connector on the other (5-pin).

• Connectors: M12 x 1 female, angled / M12 x 1 male, straight; A-coded, 5-pin, gold-plated brass (CuZn) contacts
• Cable: 1 m, PUR, black, Ø 4.8 mm, 5 x 0.34 mm², core colours BN, WH, BU, BK, GY
• Ratings: 4 A, 60 V, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nuts, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 5 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The PUR jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.

- Working temperature: 0 to 70 °C

S15LGYPQ is a Banner S15L series two-color status indicator that screws in between a sensor and its cordset. Green is on while the sensor has power, and yellow replaces it when the sensor's PNP output is active.

• Colors: green - power, yellow - sensor output active
• Input: PNP, pin 4 (black wire)
• Supply: 10...30 V DC, up to 15 mA
• Housing: Ø15 × 57.8 mm, nickel-plated brass coupling, translucent white PVC
• Environment: IP65, IP67, IP68, -40...+40 °C
• Connection: integral 4-pin M12 male and female

The indicator is fitted where the sensor's own LEDs cannot be seen, for example inside a machine or behind a guard. All four pins pass straight through from male to female, so an IO-Link sensor can also be connected through it. The input responds to PNP signals only.

Meets CE, UKCA and UL/CSA requirements, enclosure rating UL Type 1.

Remote safe I/O block for CIP Safety over EtherNet/IP. Connects up to 6 safety devices with In-Series Diagnostics (ISD) and controls 2 OSSD outputs. Power connection via M12 L-code 5-pin connector. Rated PL e / Category 4 / SIL 3.

Suitable for e-stops, safety gates, light curtains, two-hand controls, and muting applications. Non-safe PNP outputs allow standard device connection on the same block. Configures and monitors via the network - no LCD required.

• 6 configurable safety inputs with ISD
• 2 independently controlled OSSD outputs
• EtherNet/IP / CIP Safety
• Power: M12 L-code, 24 V dc
• IP65 / IP67, -25...+70 °C

Remote safe I/O block for CIP Safety over EtherNet/IP. Connects up to 6 safety devices with In-Series Diagnostics (ISD) and controls 2 OSSD outputs. Power connection via 7/8" Mini 4-pin connector - compatible with existing DeviceNet-style power trunk cabling. Rated PL e / Category 4 / SIL 3.

Suitable for e-stops, safety gates, light curtains, two-hand controls, and muting applications. Non-safe PNP outputs allow standard device connection on the same block. Configures and monitors via the network - no LCD required.

• 6 configurable safety inputs with ISD
• 2 independently controlled OSSD outputs
• EtherNet/IP / CIP Safety
• Power: 7/8" Mini, 24 V dc
• IP65 / IP67, -25...+70 °C

SMBLXR is a back-mount bracket that holds the device securely at one end.

• Mounting: back mount, at one end
• Material: zinc-plated cold-rolled steel
• Holes: Ø2.6 mm (A and B)

IM12-DI03-1S-2T-S/24VDC/CC is a 1-channel TURCK isolating switching amplifier in a 12.5 mm housing with two potential-free transistor outputs up to 10 kHz. The second output works either as a copy of the signal or as an alarm output for input faults.

• Channels: 1 input for NAMUR sensors (EN 60947-5-6) or potential-free contacts
• Outputs: 2 potential-free, short-circuit-proof transistors, ≤30 V DC, 0.1 A, ≤10 kHz
• Supply: 10...30 V DC, ≤1.03 W typical dissipation
• Housing: polycarbonate/ABS, 120 x 12.5 x 128 mm, DIN rail (NS35)
• Connection: removable spring-type terminals, 0.2...2.5 mm²
• Environment: IP20, -25...+70 °C

DIP switches on the front set the output mode, input circuit monitoring and the operating mode. An input fault makes the red LED flash according to NE44 and blocks the transistor of that channel. Mechanical contacts need either monitoring switched off or the resistor wiring shown in the datasheet.

Approvals: ATEX, cULus; for use in ATEX Zone 2. Usable in safety circuits up to SIL 2 (IEC 61508).

S100PTVD2WAD2Q is a Banner S100 Pro series touch operator display that combines status indication, text and operator input in a single M30 threaded housing. This version works without an industrial network: the PLC switches states through discrete inputs, while text, colours and animations are loaded into the unit beforehand with Banner Pro Editor.

• Display: two-row white dot-matrix display, 13 characters per line, 16 RGB LED ring and audible alert
• Control: 5 capacitive touch zones with vibration feedback, response time max. 300 ms
• Control signals: discrete inputs, output max. 150 mA
• Supply: 12-30 V DC
• Housing: black polycarbonate with tinted window, Ø100 mm, M30x1.5 threaded base, IP66/IP69K, -40...+50°C
• Connection: integral M12 male connector, 5-pin

The display mounts in a Ø30 mm hole at the machine station - pick-to-light positions, takt timer, counter and step confirmation. The configuration is loaded with Pro Editor before installation, so changing text or colours means disconnecting the unit and connecting it to a PC.

CE marked, compliant with FCC Part 15 Class B and ICES-003(B), housing rated UL Type 4X.

S100PTVD2WAKQ is a Banner S100 Pro series touch operator display that combines status indication, text and operator input in a single M30 threaded housing. Over IO-Link the controller changes text, colours and the state of each touch zone at runtime, so one unit serves several machine modes without reconfiguration.

• Display: two-row white dot-matrix display, 13 characters per line, 16 RGB LED ring and audible alert
• Control: 5 capacitive touch zones with vibration feedback, response time max. 300 ms
• Communication: IO-Link
• Supply: 18-30 V DC, 280 mA at 18 V DC, 210 mA at 24 V DC
• Housing: black polycarbonate with tinted window, Ø100 mm, M30x1.5 threaded base, IP66/IP69K, -40...+50°C
• Connection: integral M12 male connector, 4-pin

The display mounts in a Ø30 mm hole at the machine station - pick-to-light positions, takt timer, counter and step confirmation. Note that this version starts at 18 V DC, not 12 V DC as the other S100 Pro versions.

CE marked, compliant with FCC Part 15 Class B and ICES-003(B), housing rated UL Type 4X.

S100PTVD2WASQ is a Banner S100 Pro series touch operator display that combines status indication, text and operator input in a single M30 threaded housing. The controller changes text, colours and the meaning of each touch zone at runtime over Modbus RTU, so one unit serves several machine modes without reconfiguration.

• Display: two-row white dot-matrix display, 13 characters per line, 16 RGB LED ring and audible alert
• Control: 5 capacitive touch zones with vibration feedback, response time max. 300 ms
• Communication: Modbus RTU over RS-485, 9600, 19200 and 38400 bit/s
• Supply: 12-30 V DC, 415 mA at 12 V DC, 210 mA at 24 V DC
• Housing: black polycarbonate with tinted window, Ø100 mm, M30x1.5 threaded base, IP66/IP69K, -40...+50°C
• Connection: integral M12 male connector, 4-pin

The display mounts in a Ø30 mm hole at the machine station - pick-to-light positions, takt timer, counter and step confirmation. Prepared modes run without programming, while Modbus registers let the PLC drive each row, colour and the audible alert separately.

CE marked, compliant with FCC Part 15 Class B and ICES-003(B), housing rated UL Type 4X.

RSr-L-SIL-8A-Q is a remote safety relay from Banner's RSr family. It converts the OSSD outputs of a safety device into two volt-free normally open relay contacts, so a light curtain, a safety I/O block or a safety PLC can switch loads that do not tolerate OSSD test pulses. This is the latch model: after a stop the outputs stay off until a reset signal is applied on the A-code port.

• Input: one dual-channel OSSD pair, ON threshold > 15 V DC, OFF below 5 V DC
• Output: two normally open safety contacts, 8 A at 24 V DC (DC1) per IEC/EN 60947-5-1
• Supply: 24 V DC ±20 %, under 100 mA, approximately 2 W
• Response time 20 ms maximum, minimum OFF-state recovery 400 ms
• Housing: thermoplastic polyurethane, IP65 / IP67, 138 × 50 × 27.8 mm, −25 °C to +60 °C
• Connection: four 5-pin M12 connectors — two A-code for signals and reset, two L-code for the switched power

The relay mounts directly on the machine with two M4 screws or a bracket, so distributed safety outputs can switch motors, valves and brakes without a control cabinet. There are no DIP switches and nothing to program. Four LED indicators show status, fault, both safety inputs and the relay output.

SIL 3 per IEC 61508 and EN 62061, Category 4 / PL e per EN ISO 13849-1; CE marked and UL listed.

RSr-L-SIT-8A-Q is a remote safety relay from Banner's RSr family. It converts the OSSD outputs of a safety device into two volt-free normally open relay contacts, so a light curtain, a safety I/O block or a safety PLC can switch loads that do not tolerate OSSD test pulses. This is the trip model: the contacts follow the safety inputs directly, and pin 5 of the A-code port carries an auxiliary output that mirrors the relay state.

• Input: one dual-channel OSSD pair, ON threshold > 15 V DC, OFF below 5 V DC
• Output: two normally open safety contacts, 8 A at 24 V DC (DC1) per IEC/EN 60947-5-1, plus a 24 V DC 70 mA solid-state AUX output
• Supply: 24 V DC ±20 %, under 100 mA, approximately 2 W
• Response time 20 ms maximum, minimum OFF-state recovery 400 ms
• Housing: thermoplastic polyurethane, IP65 / IP67, 138 × 50 × 27.8 mm, −25 °C to +60 °C
• Connection: four 5-pin M12 connectors — two A-code for signals and the AUX output, two L-code for the switched power

The relay mounts directly on the machine with two M4 screws or a bracket, so distributed safety outputs can switch motors, valves and brakes without a control cabinet. There are no DIP switches and nothing to program. Four LED indicators show status, fault, both safety inputs and the relay output.

SIL 3 per IEC 61508 and EN 62061, Category 4 / PL e per EN ISO 13849-1; CE marked and UL listed.

LMB1822FM is an aluminium adapter for mounting the Banner S18L indicator, which has an M18 × 1 thread, in a standard 22 mm hole.

• Fits: M18 × 1 thread into a 22 mm hole (22 × 1.5 mm)
• Material: aluminium, black
• Mounting: flush
• Included: adapter, nut, gasket

CMVT-QR20-IOLX3-H1141 is a condition monitoring vibration and temperature sensor measuring acceleration and velocity over three axes plus the housing temperature. It is intended for rotating machine parts where rising vibration indicates bearing wear, imbalance or shaft misalignment, so the deviation is caught before a failure.

• Measuring range: acceleration 16 g RMS (6.6 kHz sampling), velocity 0...320 mm/s RMS @ 78 Hz, temperature -40...+85°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: velocity linearity deviation ≤ ±1 % @ 78 Hz, acceleration ≤ ±3 % @ 78 Hz; repeatability ≤ ±5 % @ 78 Hz
• Outputs: pin 4 - IO-Link or SIO, pin 2 - SIO; two PNP/NPN switching outputs in SIO mode; IO-Link COM 3 (230.4 kBaud)
• Supply: 18...30 VDC (IO-Link), 10...30 VDC (SIO), consumption < 50 mA
• Protection: against wire break and reverse polarity
• Housing: rectangular QR20, Ultem plastic, 71.6 x 62.6 x 20 mm
• Environment: IP68/IP69K, pollution degree 3, shock 200 g (4 ms), vibration 20 g
• Connection: M12 x 1 male connector, 4-pin

Over IO-Link the output quantity is selectable - acceleration or velocity, RMS or peak-to-peak - and the switching thresholds are set there. Thresholds can be parameterised to the ISO 10816-3 machine classes or defined freely. A green LED shows the supply and, when flashing, active IO-Link communication; two yellow LEDs show an exceeded threshold.

UL registration number E351232. MTTF 548 years to SN 29500 (Ed. 99) at 40°C. Shock tested to EN 60068-2-27, vibration to EN 60068-2-6, temperature cycling to EN 60068-2-14 (20 cycles).

CMVT-QR20-IOLX3-H1141/3GD is a condition monitoring vibration and temperature sensor measuring acceleration and velocity over three axes plus the housing temperature. It is the ATEX version of the CMVT-QR20 for zones 2 and 22 - the measuring side is unchanged, but the device carries an Ex marking and a narrower permitted ambient range.

• Measuring range: acceleration 16 g RMS (6.6 kHz sampling), velocity 0...320 mm/s RMS @ 78 Hz, temperature -40...+85°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: velocity linearity deviation ≤ ±1 % @ 78 Hz, acceleration ≤ ±3 % @ 78 Hz; repeatability ≤ ±5 % @ 78 Hz
• Outputs: pin 4 - IO-Link or SIO, pin 2 - SIO; two PNP/NPN switching outputs in SIO mode; IO-Link COM 3 (230.4 kBaud)
• Supply: 18...30 VDC (IO-Link), 10...30 VDC (SIO), consumption < 50 mA
• Protection: against wire break and reverse polarity
• Housing: rectangular QR20, Ultem plastic, 71.6 x 62.6 x 20 mm
• Environment: IP68/IP69K, pollution degree 3, shock 200 g (4 ms), vibration 20 g; permitted ambient in the ATEX zone -30...+70°C
• Connection: M12 x 1 male connector, 4-pin

Device marking: Ex II 3 G Ex ec IIC T4 Gc / II 3 D Ex tc. The plug connection must not be disconnected under voltage, and the sensor must be protected against mechanical damage.

Over IO-Link the output quantity is selectable - acceleration or velocity, RMS or peak-to-peak - and the switching thresholds are set there. Thresholds can be parameterised to the ISO 10816-3 machine classes or defined freely. A green LED shows the supply and, when flashing, active IO-Link communication; two yellow LEDs show an exceeded threshold.

UL registration number E351232. MTTF 548 years to SN 29500 (Ed. 99) at 40°C. Shock tested to EN 60068-2-27, vibration to EN 60068-2-6, temperature cycling to EN 60068-2-14 (20 cycles).

CMVT-M8TA1X-LI2IOL-H1141 is a stainless steel vibration and temperature sensor with an M8 screw-in thread, measuring over one axis at a 23.6 kHz sampling rate. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: acceleration 10 g RMS / 14 g peak, velocity 0...128 mm/s RMS @ 159 Hz, temperature -40...+80°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: ≤ ±0.5 % @ 159 Hz; temperature linearity deviation ≤ 10 %
• Outputs: pin 4 - IO-Link or SIO, pin 2 - 4...20 mA or SIO; IO-Link COM 2 (38.4 kBaud)
• Supply: 18...30 VDC, consumption < 120 mA in IO-Link mode
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms), vibration 20 g
• Connection: M12 x 1 connector, 4-pin

Frequency ranges and switching thresholds are configurable over IO-Link, so only the band in which a given machine's fault appears has to be watched. The 4...20 mA output on pin 2 carries the same quantity in analogue form, so the sensor connects to a controller with no IO-Link master.

MTTF 164 years to SN 29500 (Ed. 99). Shock tested to EN 60068-2-27, vibration to EN 60068-2-6.

CMVT-M8TE1X-LI2IOL-H1141 is a stainless steel vibration and temperature sensor with an M8 screw-in thread and a 64 kHz sampling rate. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: acceleration 33.9 g RMS / 48 g peak (10 Hz...10 kHz), velocity 0...256 mm/s RMS @ 159 Hz, temperature -40...+80°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: ≤ ±0.5 % @ 159 Hz; temperature linearity deviation ≤ 10 %
• Outputs: pin 4 - IO-Link or SIO, pin 2 - 4...20 mA or SIO; IO-Link COM 3 (230.4 kBaud)
• Supply: 18...30 VDC, consumption < 120 mA in IO-Link mode
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms)
• Connection: M12 x 1 connector, 4-pin

Besides the aggregated RMS values the sensor outputs a bearing condition indicator and transfers the raw signal over IO-Link BLOB at up to 64 kHz with a low-pass filter at 12 kHz. FFT analysis can therefore be done off the sensor - on the controller or a server. Frequency ranges and thresholds are configurable over IO-Link.

MTTF 112 years to SN 29500 (Ed. 99) at 40°C. Shock tested to EN 60068-2-27.

CMVT-M8TA1X-LI220-H1141 is a stainless steel vibration sensor with an M8 screw-in thread that measures the velocity RMS value over one axis and outputs it as a 4...20 mA signal, where 20 mA corresponds to 20 mm/s RMS. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: velocity 0...20 mm/s RMS, one axis, 23.6 kHz sampling
• Accuracy: ≤ ±0.5 % @ 159 Hz
• Outputs: 4...20 mA, load resistance ≤ 0.5 kΩ
• Supply: 18...30 VDC, consumption < 100 mA
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms), vibration 20 g
• Connection: M12 x 1 connector, 4-pin

There is no IO-Link and nothing to configure - the sensor wires straight into a controller's analogue input, and the measuring span is fixed by the model chosen.

MTTF 164 years to SN 29500 (Ed. 99). Shock tested to EN 60068-2-27, vibration to EN 60068-2-6.

CMVT-M8TA1X-LI225-H1141 is a stainless steel vibration sensor with an M8 screw-in thread that measures the velocity RMS value over one axis and outputs it as a 4...20 mA signal, where 20 mA corresponds to 25 mm/s RMS. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: velocity 0...25 mm/s RMS, one axis, 23.6 kHz sampling
• Accuracy: ≤ ±0.5 % @ 159 Hz
• Outputs: 4...20 mA, load resistance ≤ 0.5 kΩ
• Supply: 18...30 VDC, consumption < 100 mA
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms), vibration 20 g
• Connection: M12 x 1 connector, 4-pin

There is no IO-Link and nothing to configure - the sensor wires straight into a controller's analogue input, and the measuring span is fixed by the model chosen.

MTTF 164 years to SN 29500 (Ed. 99). Shock tested to EN 60068-2-27, vibration to EN 60068-2-6.

CMTH-M12-IOL6X2-H1141 is a capacitive humidity and temperature sensor for condition monitoring. It is intended for machine parts where temperature or humidity affects machine availability or process quality, and suits both indoor and outdoor use.

• Accuracy: temperature ±0.8°C; humidity ±5 % RH (10...90 % RH), ±7 % RH (0...10 % and 90...100 % RH). When installed in metal, in an environment with convection
• Measuring range: temperature -40...+100°C, humidity 0...100 % RH, resolution 0.1 K and 0.1 % RH; humidity response time t63 6 s
• Outputs: output 1 - switching or IO-Link, output 2 - switching; IO-Link v1.1 COM 3, Class A, Smart Sensor Profile 4
• Supply: 18...30 VDC, DC 4-wire, consumption < 50 mA, rated current ≤ 150 mA
• Protection: against short circuit, wire break and reverse polarity
• Housing: chrome-plated CuZn metal, M12 x 1 thread, nut torque up to 10 Nm
• Environment: IP67, operating temperature -40...+100°C
• Connection: M12 x 1 connector, 4-pin, cable up to 20 m

Over IO-Link a temperature offset is configurable and switching thresholds or windows can be set for temperature and humidity. The sensor calculates the dew point, builds temperature and humidity histograms and counts operating hours and threshold transitions. A green LED shows the supply.

Meets CE and UL requirements. EMC to EN 61326-1, shock to IEC 60068-2-27 (50 g, 6 ms), vibration to IEC 60068-2-6 (10...150 Hz, 20 g). MTTF 610 years.

CMTH-M12-IOL6X2-H1141/3GD is a capacitive humidity and temperature sensor for condition monitoring in the ATEX version for zones 2 and 22. It is intended for machine parts where temperature or humidity affects machine availability or process quality, and suits both indoor and outdoor use.

• Accuracy: temperature ±0.8°C; humidity ±5 % RH (10...90 % RH), ±7 % RH (0...10 % and 90...100 % RH). When installed in metal, in an environment with convection
• Measuring range: temperature -40...+100°C, humidity 0...100 % RH, resolution 0.1 K and 0.1 % RH; humidity response time t63 6 s
• Outputs: output 1 - switching or IO-Link, output 2 - switching; IO-Link v1.1 COM 3, Class A, Smart Sensor Profile 4
• Supply: 18...30 VDC, DC 4-wire, consumption < 50 mA, rated current ≤ 150 mA
• Protection: against short circuit, wire break and reverse polarity
• Housing: chrome-plated CuZn metal, M12 x 1 thread, nut torque up to 10 Nm
• Environment: IP67, operating temperature -40...+100°C; ATEX category II 3 G (Ex zone 2) and II 3 D (Ex zone 22)
• Connection: M12 x 1 connector, 4-pin, cable up to 20 m

Over IO-Link a temperature offset is configurable and switching thresholds or windows can be set for temperature and humidity. The sensor calculates the dew point, builds temperature and humidity histograms and counts operating hours and threshold transitions. A green LED shows the supply.

Meets CE and UL requirements. EMC to EN 61326-1, shock to IEC 60068-2-27 (50 g, 6 ms), vibration to IEC 60068-2-6 (10...150 Hz, 20 g). MTTF 610 years.

CMTH-M12E-IOL6X2-H1141 is a capacitive humidity and temperature sensor for condition monitoring with an integrated heating function that stabilises the measurement. It is intended for machine parts where temperature or humidity affects machine availability or process quality, and suits both indoor and outdoor use.

• Accuracy: temperature ±0.5°C; humidity ±3.5 % RH (10...90 % RH), ±5 % RH (0...10 % and 90...100 % RH). When installed in metal, in an environment with convection
• Measuring range: temperature -40...+100°C, humidity 0...100 % RH, resolution 0.1 K and 0.1 % RH
• Outputs: output 1 - switching or IO-Link, output 2 - switching; IO-Link v1.1 COM 3, Class A, Smart Sensor Profile 4
• Supply: 18...30 VDC, DC 4-wire, consumption < 50 mA, rated current ≤ 150 mA
• Protection: against short circuit, wire break and reverse polarity
• Housing: chrome-plated CuZn metal, M12 x 1 thread, nut torque up to 10 Nm
• Environment: IP67, operating temperature -40...+100°C
• Connection: M12 x 1 connector, 4-pin, cable up to 20 m

Over IO-Link a temperature offset is configurable and switching thresholds or windows can be set for temperature and humidity. The sensor calculates the dew point, builds temperature and humidity histograms and counts operating hours and threshold transitions. A green LED shows the supply.

Meets CE and UL requirements. EMC to EN 61326-1, shock to IEC 60068-2-27 (50 g, 6 ms), vibration to IEC 60068-2-6 (10...150 Hz, 20 g). MTTF 610 years.

CMMT-QR20-IOL6X3-H1141 is a magnetic field sensor for condition monitoring that measures the field over three axes, calculates the sum vector and reads temperature as well. It is intended for positions where a change in the magnetic field reports on machine condition - the weakening of a permanent magnet, or the influence of a stray field.

• Measuring range: magnetic field -2500...+2500 µT, resolution 1 µT; temperature -25...+70°C, resolution 0.1 K
• Response time: at least 8 s
• Outputs: output 1 - PNP/NPN or IO-Link, output 2 - PNP/NPN; IO-Link COM 3 (230.4 kBaud), Smart Sensor Profile
• Supply: 18...30 VDC, no-load current 80 mA, rated current ≤ 250 mA
• Protection: against short circuit (cyclic), wire break and reverse polarity
• Housing: rectangular QR20, Ultem plastic, 71.6 x 62.6 x 20 mm
• Environment: IP68/IP69K, pollution degree 3, operating temperature -25...+70°C
• Connection: M12 x 1 male connector, 4-pin

Over IO-Link an offset and a limit value can be set per axis and assigned to a specific switching output, so which direction is changing can be separated out. A green LED shows the supply, two yellow LEDs the output states.

EMC to EN 61326-1.

MAGKIT-M8T is the magnetic mount for the CMVT-M8T family of vibration sensors. The sensor screws into the magnet's female thread, and the magnet is placed on the machine surface without drilling or cutting a thread in the equipment itself.

• Fits: CMVT-M8T family sensors with an M8 screw-in thread
• Thread: M8 x 12 mm, female
• Material: stainless steel V4A
• Holding force: 342 N at 28°C

The mount is intended for flexible, relocatable mounting. Permanent and operationally secure fixing depends on the conditions at the application and must be evaluated by the user.

MAGKIT-M5 is the magnetic mounting kit for CMVT-QR20 rectangular-housing sensors. The sensor is screwed to two magnets with the supplied M5 screws, and the magnets hold it on the machine surface without drilling a hole in the equipment.

• Fits: CMVT-QR20 and CMMT-QR20 family sensors
• Supplied: 2 mounting magnets, 2 washers, 2 M5 x 12 screws
• Dimensions: magnet Ø 32 x 7 mm, M5 female thread

Permanent and operationally secure fixing depends on the conditions at the application and must be evaluated by the user.

MTL7787P+ is a two-channel Zener barrier from the Eaton Crouse-Hinds MTL7700 series for intrinsically safe analogue and digital signal loops. Both channels are positive polarity: channel 1 is rated 28 V / 234 Ω / 119 mA, channel 2 is a diode return channel.

• Channel 1: safety description 28 V, 234 Ω, 119 mA; max end-to-end resistance 253 Ω
• Channel 2: 28 V diode return, 0.9 V + 21 Ω
• Working voltage: 26.4 V at 10 µA; Vmax 27.2 V; fuse rating 80 mA
• Housing: polycarbonate, 12.6 x 90 x 105 mm, approx. 140 g
• Mounting: 35 mm DIN rail, earthed through the rail
• Environment: IP20, -20...+60 °C

Hazardous area ratings: IECEx/ATEX Zone 0 and Zone 2; NEC Class I, Division 2 and Class I, Zone 2.