NI8U-M12-AP6X-0.2-PSG3M is a Turck uprox Factor 1 inductive sensor in an M12 chrome-plated brass housing with an 8 mm switching distance for non-flush mounting.

• Sensing distance: 8 mm, non-flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: PNP, NO; up to 200 mA; switching frequency 2 kHz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: M12 x 1 thread, thread length 35 mm, chrome-plated brass, LCP sensing face, nut torque up to 10 Nm
• Environment: IP68, ambient temperature -30...+85 °C
• Connection: 0.2 m PUR cable (LifYY-11Y), 3 x 0.14 mm², Ø 3 mm, with M8 x 1 connector, 3-pin, nickel-plated brass coupling nut

Factor 1: the switching distance is the same for steel, stainless steel, aluminium and brass, so no correction factor applies when the target metal changes. The sensor is immune to magnetic DC and AC fields up to 300 mT.

A yellow LED shows the switching state. MTTF 874 years acc. to SN 29500 (40 °C).

IWRM 18I9511 is a Baumer inductive distance sensor with a 2...5 mm measuring range and a 4...20 mA current output. The analogue signal follows the distance to a metal target, so position or deflection can be read continuously instead of as a switch point.

• Accuracy: linearity error ±100 µm, repeatability 0.02 mm, temperature coefficient 1 µm/(K·mm)
• Measuring range: 2...5 mm, reference distance 3.25...3.75 mm, measuring speed < 1 mm/ms
• Output: current 4...20 mA, load resistance 500...1000 Ohm
• Supply: 15...30 VDC, 3-wire, consumption max. 35 mA; short-circuit and reverse polarity protection
• Housing: M18 x 1 nickel-plated brass, PBT sensing face, length 31.5 mm, flush mounting, tightening torque max. 40 Nm (front 28 Nm)
• Environment: IP67, operating temperature 0...+60 °C
• Connection: 2 m cable

The 31.5 mm housing fits where a standard M18 sensor is too long, for example in fixtures or tight machine frames.

BI10U-M18-AP6X-H1141 is a TURCK uprox3 inductive sensor with an extended 10 mm switching distance in an M18 housing. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 10 mm, flush mounting
• Output: PNP, NO, 3-wire, max. 200 mA, switching frequency 1.5 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M18 x 1 chrome-plated brass, LCP sensing face, thread length 36 mm, nut torque max. 10 Nm
• Environment: IP68, operating temperature -25...+70 °C
• Connection: M12 connector, 4-pin

A yellow LED shows the switching state.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

BI2-EG08-AN6X-H1341 is a Turck inductive sensor in an M8 x 1 stainless steel housing with an increased 2 mm switching distance for flush mounting.

• Sensing distance: 2 mm, flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: NPN, NO; up to 150 mA; switching frequency 3 kHz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: M8 x 1 thread, stainless steel 1.4305 (AISI 303), PA6.6 sensing face, thread length 40 mm, nut torque up to 5 Nm
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: M12 x 1 connector, 4-pin

A yellow LED shows the switching state. Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

BI15-CP40-VP4X2/S97 is a TURCK rectangular inductive sensor with a 15 mm switching distance in a 40 x 40 mm CP40 housing with terminals. The /S97 version is rated down to -40 °C.

• Switching distance: 15 mm, flush
• Output: PNP, complementary (NO + NC), 4-wire, max. 200 mA; short-circuit, wire-break and reverse polarity protection, switching frequency 150 Hz
• Supply: 10...65 VDC, no-load current 15 mA
• Housing: rectangular CP40, 114 x 40 x 40 mm, PBT-GF30-V0
• Environment: IP67, operating temperature -40...+70 °C
• Connection: terminal chamber, conductors up to 2.5 mm², M20 x 1.5 cable entry

The sensing head turns to 9 positions, and two green and two yellow corner LEDs show power and switching state from any side.

Correction factors (St37 = 1): stainless steel 0.7, brass 0.4, aluminium 0.3. MTTF 2283 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

IPRM 12I9505/S14 is a Baumer high-precision inductive distance sensor with a 0...2 mm measuring range and a 0...20 mA current output. It measures the distance to a metal target without contact, with a resolution below 0.012 µm RMS.

• Accuracy: linearity error ±60 µm, repeatability < 1 µm, temperature drift ±10 µm
• Measuring range: 0...2 mm, resolution < 0.012 µm RMS (static, 10 Hz), < 0.065 µm RMS (dynamic, 520 Hz), measuring speed < 1 mm/ms
• Output: current 0...20 mA, load resistance 100...400 Ohm
• Supply: 15...30 VDC, 3-wire, consumption max. 50 mA; short-circuit and reverse polarity protection
• Housing: M12 x 1 steel thread, ceramic sensing face, length 90 mm, quasi-flush mounting
• Environment: IP67, operating temperature 0...+60 °C
• Connection: M12 connector, 4-pin

Used where position or runout must be measured in the micrometre range, for example shaft runout, gap or thickness checks. The sensor housing must be connected to earth.

BI2-EG08-RN6X is a Turck inductive sensor in an M8 x 1 stainless steel housing with an increased 2 mm switching distance for flush mounting.

• Sensing distance: 2 mm, flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: NPN, NC; up to 150 mA; switching frequency 3 kHz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: M8 x 1 thread, stainless steel 1.4305 (AISI 303), PA6.6 sensing face, thread length 40 mm, nut torque up to 5 Nm
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: 2 m PUR cable (LifY-11Y), 3 x 0.14 mm², Ø 3.3 mm

A yellow LED shows the switching state. Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

IGYX 12P17B3/S14L is a Baumer inductive proximity sensor in an M12 barrel with a 4 mm nominal sensing distance and a PNP normally open (NO) output. The sensing face is flush mountable and the nickel-plated brass housing is 50 mm long.

• Sensing distance: 4 mm (Sn), assured 3.2 mm (Sa)
• Output: PNP, normally open (NO), 200 mA, with short-circuit and reverse-polarity protection
• Supply: 10...30 V DC, current consumption up to 15 mA with no load
• Housing: M12 thread, nickel-plated brass, PBT sensing face, 50 mm long, flush mountable
• Environment: IP 67, operating temperature -25...+75 °C
• Connection: M12 connector

The sensor is intended for presence and end-position monitoring of metal parts on conveyors, pneumatic cylinders and indexing mechanisms. Switching frequency is 1.5 kHz. Tightening torque on the M12 thread must not exceed 10 Nm, and the switching point drifts by up to ±10 % of Sr across the temperature range, which matters when the target sits close to the 4 mm limit.

Complies with the EMC requirements of EN 60947-5-2:2007.

NI5-G12-Y1X is a TURCK inductive sensor with a NAMUR output to EN 60947-5-6, approved for ATEX zones 0 and 20. It connects to an intrinsically safe isolating amplifier.

• Switching distance: 5 mm, non-flush mounting; correction factors steel 1, stainless steel 0.7, brass 0.4, aluminium 0.3
• Output: NAMUR, 2-wire, ≥ 2.1 mA not actuated / ≤ 1.2 mA actuated, switching frequency 2 kHz
• Supply: nom. 8.2 VDC from the isolating amplifier
• Housing: M12 x 1 chrome-plated brass, PA12-GF30 sensing face, thread length 20 mm, nut torque max. 10 Nm
• Environment: IP67, operating temperature -25...+70 °C
• Connection: 2 m blue PVC cable, 2 x 0.34 mm², Ø 5.2 mm

Suitable for safety-related systems up to SIL 2 (IEC 61508) and PL c (ISO 13849-1) in a single-channel setup. A yellow LED shows the switching state.

ATEX II 1 G Ex ia IIC T6 Ga / II 1 D Ex ia IIIC T135 °C Da (KEMA 02 ATEX 1090X). MTTF 6198 years (SN 29500, 40 °C).

BI8U-M18M-VP6X-H1141 is a TURCK uprox inductive sensor with an extended 8 mm switching distance in an M18 housing. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 8 mm, flush mounting
• Output: PNP, complementary (NO + NC), 4-wire, max. 200 mA, switching frequency 1.5 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M18 x 1 chrome-plated brass, LCP sensing face, thread length 46 mm, nut torque max. 25 Nm
• Environment: IP68, operating temperature -30...+85 °C
• Connection: M12 connector, 4-pin

A yellow LED shows the switching state.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

BI8-Q10-VP68X2-0.3-RS4.4 is a TURCK rectangular inductive sensor for vehicle electrical systems with 12 V and 24 V supply, with E1 type approval from the German Federal Motor Transport Authority. Correction factors: steel St37 = 1, stainless steel 0.7, brass 0.4, aluminium 0.3, so non-ferrous targets are detected at a shorter distance.

• Switching distance: 8 mm, flush mounting
• Output: PNP, complementary (NO + NC), 4-wire, max. 200 mA, switching frequency 1 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 8.6...30 VDC, no-load current 15 mA
• Housing: rectangular Q10, 42 x 25 x 10.8 mm, PBT-GF30-V0, active face on top, laser-engraved label
• Environment: IP68 / IP69K, operating temperature -40...+85 °C
• Connection: 0.3 m PUR cable, 4 x 0.14 mm², Ø 3 mm, M12 male connector, 4-pin, nickel-plated brass coupling nut

Interference immunity 100 V/m radiated (ISO 11452-4) and 100 mA BCI (ISO 11452-2). Salt spray tested to EN 60068-2-52 severity 5, rapid temperature change -40...+85 °C to EN 60068-2-14. A green LED shows power and a yellow LED the switching state.

E1 type approval. Shock 150 g (6 ms) to EN 60068-2-27, vibration 20 g (10...3000 Hz) to EN 60068-2-6. MTTF 2283 years (SN 29500, 40 °C).

BI15U-CP40-VP4X2 is a TURCK uprox rectangular inductive sensor with a 15 mm switching distance in a 40 x 40 mm CP40 housing with terminals. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 15 mm, flush
• Output: PNP, complementary (NO + NC), 4-wire, max. 200 mA; short-circuit, wire-break and reverse polarity protection, switching frequency 250 Hz
• Supply: 10...65 VDC, no-load current 15 mA
• Housing: rectangular CP40, 114 x 40 x 40 mm, PBT-GF30-V0
• Environment: IP68, operating temperature -30...+85 °C
• Connection: terminal chamber, conductors up to 2.5 mm², M20 x 1.5 cable entry

The sensing head turns to 9 positions, and two green and two yellow corner LEDs show power and switching state from any side.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

NI8U-EM12-AP6X is a TURCK uprox inductive sensor. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 8 mm, non-flush mounting, partially embeddable
• Output: PNP, NO, 3-wire, max. 200 mA, switching frequency 1 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M12 x 1 stainless steel 1.4301, PBT sensing face, thread length 35 mm, nut torque max. 10 Nm
• Environment: IP68, operating temperature -30...+85 °C
• Connection: 2 m PVC cable, 3 x 0.34 mm², Ø 5.2 mm

A yellow LED shows the switching state.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

BI2-M08E-VP6X-V1141 is a TURCK inductive sensor with an extended 2 mm switching distance in a flush-mounted M8 housing. Correction factors: steel St37 = 1, stainless steel 0.7, brass 0.4, aluminium 0.3, so non-ferrous targets are detected at a shorter distance.

• Switching distance: 2 mm, flush mounting
• Output: PNP, complementary (NO + NC), 4-wire, max. 150 mA, switching frequency 2.8 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 15 mA
• Housing: M8 x 1 nickel-plated brass, PP-GF20 sensing face, thread length 40 mm, nut torque max. 7 Nm
• Environment: IP67, operating temperature -25...+70 °C
• Connection: M8 connector, 4-pin

MTTF 2283 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

NI40U-CP40-VP4X2 is a TURCK uprox rectangular inductive sensor with a 40 mm switching distance in a 40 x 40 mm CP40 housing with terminals. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 40 mm, non-flush
• Output: PNP, complementary (NO + NC), 4-wire, max. 200 mA; short-circuit, wire-break and reverse polarity protection, switching frequency 250 Hz
• Supply: 10...65 VDC, no-load current 15 mA
• Housing: rectangular CP40, 114 x 40 x 40 mm, PBT-GF30-V0
• Environment: IP68, operating temperature -30...+85 °C
• Connection: terminal chamber, conductors up to 2.5 mm², M20 x 1.5 cable entry

The sensing head turns to 9 positions, and two green and two yellow corner LEDs show power and switching state from any side.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

IGC222 (IGK2008BFRKG/2LED/US-104) is an ifm 2-wire DC inductive sensor with an 8 mm sensing range, for machine tools and areas exposed to coolants and lubricants. The output works as PNP or NPN and NO or NC is selectable.

• Sensing range: 8 mm, operating distance 0...6.5 mm, flush mountable
• Output: 2-wire DC, PNP/NPN, NO/NC selectable, 100 mA, switching frequency 400 Hz, leakage current 1 mA
• Supply: 10...30 VDC; short-circuit (pulsed), overload and reverse polarity protection
• Housing: M18 x 1, white-bronze-coated brass, white LCP sensing face, length 70 mm, tightening torque 25 Nm
• Environment: IP68 (coolant), operating temperature -25...+70 °C
• Connection: M12 connector, A-coded, 2-pin, gold-plated contacts

Four yellow LEDs at 90° show the switching state, and a red LED serves as a setting aid during mounting. Minimum load current is 4 mA, which matters when connecting a 2-wire sensor to a PLC input.

EMC to EN 55011 class B. MTTF 1424 years.

BI10U-M18-VP6X-H1141 is a TURCK uprox3 inductive sensor with an extended 10 mm switching distance in an M18 housing. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 10 mm, flush mounting
• Output: PNP, complementary (NO + NC), 4-wire, max. 200 mA, switching frequency 1.5 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M18 x 1 chrome-plated brass, LCP sensing face, thread length 36 mm, nut torque max. 10 Nm
• Environment: IP68, operating temperature -25...+70 °C
• Connection: M12 connector, 4-pin

A yellow LED shows the switching state.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

IGYX 08P17B3/S35L is a Baumer inductive proximity sensor in an M8 barrel with a 2 mm nominal sensing distance and a PNP normally open (NO) output. The sensing face is flush mountable and the stainless steel housing is 36 mm long.

• Sensing distance: 2 mm (Sn), assured 1.6 mm (Sa)
• Output: PNP, normally open (NO), 200 mA, with short-circuit and reverse-polarity protection
• Supply: 10...30 V DC, current consumption up to 15 mA with no load
• Housing: M8 thread, stainless steel, PBT sensing face, 36 mm long, flush mountable
• Environment: IP 67, operating temperature -25...+75 °C
• Connection: M8 connector

The Ø 8 mm body and 36 mm length fit the sensor into grippers, indexing tables and other positions where an M12 barrel does not fit. A 3 kHz switching frequency is enough for presence monitoring of fast moving metal parts. Tightening torque on the M8 thread must not exceed 5 Nm, and the switching point drifts by up to ±10 % of Sr across the temperature range, which matters when the target sits close to the 2 mm limit.

Complies with the EMC requirements of EN 60947-5-2:2007.

BI15-CK40-AP6X2-H1141 is a TURCK inductive sensor with a 15 mm switching distance in a flush-mountable CK40 rectangular housing. The sensing head turns to 5 positions, and two green and two yellow corner LEDs show power and switching state from any side.

• Switching distance: 15 mm, flush mounting
• Output: PNP, NO, 3-wire, max. 200 mA; short-circuit, wire-break and reverse polarity protection, switching frequency 0.15 kHz
• Supply: 10...30 VDC, no-load current 15 mA
• Housing: rectangular CK40, 65 x 40 x 40 mm, PBT-GF20-V0, PA12-GF30 sensing face
• Environment: IP67, operating temperature -25...+70 °C
• Connection: M12 connector, 4-pin

Correction factors (St37 = 1): stainless steel 0.7, brass 0.4, aluminium 0.3. The BS1-CK40 mounting part is included.

MTTF 2283 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

BI3-Q06-AP6X2 is a Turck inductive sensor in a flat rectangular Q06 plastic housing, 6 mm high, with the sensing face on top.

• Sensing distance: 3 mm, flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: PNP, NO; up to 200 mA; switching frequency 1 kHz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: Q06, 27.8 x 17.3 x 6 mm, PP plastic, PA12-GF30 sensing face
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: 2 m PUR cable (LifY-11Y), 3 x 0.25 mm², Ø 4 mm; suitable for drag chains (Turck declaration H1063M)

A green LED shows power and a yellow LED the switching state. Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

BI10-M30-LIU is a Turck inductive sensor in an M30 threaded housing with analog output, for flush mounting. Its output signal is proportional to the distance of a metal target and linear across the whole measuring range. The sensor is intended for simple control tasks where the distance matters, not just presence.

• Accuracy: linearity deviation 3 %, repeatability ≤ 1 % of measuring range (0.5 % after 0.5 h warm-up), reproducibility ≤ 50 µm (≤ 25 µm after warm-up), temperature drift ≤ ±0.06 %/K
• Measuring range: 3...8 mm (St37 steel target)
• Outputs: voltage 0...10 V (load ≥ 4.7 kΩ) and current 0...20 mA (load ≤ 0.4 kΩ); measuring frequency 140 Hz
• Supply: 15...30 VDC, 4-wire, no-load current 8 mA
• Protection: short circuit and reverse polarity; no wire-break protection
• Housing: M30 x 1.5 thread, thread length 55 mm, chrome-plated brass, PA12-GF30 sensing face, nut torque up to 75 Nm
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: 2 m PVC cable (LifYY), 4 x 0.34 mm², Ø 5.2 mm

Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 751 years acc. to SN 29500 (40 °C).

BI10-M30-LIU 5M is a Turck inductive sensor in an M30 threaded housing with analog output, for flush mounting. Its output signal is proportional to the distance of a metal target and linear across the whole measuring range. The sensor is intended for simple control tasks where the distance matters, not just presence.

• Accuracy: linearity deviation 3 %, repeatability ≤ 1 % of measuring range (0.5 % after 0.5 h warm-up), reproducibility ≤ 50 µm (≤ 25 µm after warm-up), temperature drift ≤ ±0.06 %/K
• Measuring range: 3...8 mm (St37 steel target)
• Outputs: voltage 0...10 V (load ≥ 4.7 kΩ) and current 0...20 mA (load ≤ 0.4 kΩ); measuring frequency 140 Hz
• Supply: 15...30 VDC, 4-wire, no-load current 8 mA
• Protection: short circuit and reverse polarity; no wire-break protection
• Housing: M30 x 1.5 thread, thread length 55 mm, chrome-plated brass, PA12-GF30 sensing face, nut torque up to 75 Nm
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: 5 m PVC cable (LifYY), 4 x 0.34 mm², Ø 5.2 mm

Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 751 years acc. to SN 29500 (40 °C).

BI4U-M12-AP6X-H1141 is a TURCK uprox+ inductive sensor with an extended 4 mm switching distance in an M12 housing. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 4 mm, flush mounting, factor 1 for all metals
• Output: PNP, NO, 3-wire, max. 200 mA; short-circuit, wire-break and reverse polarity protection, switching frequency 3 kHz
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M12 x 1 chrome-plated brass, LCP sensing face, thread length 36 mm, nut torque max. 10 Nm
• Environment: IP68, operating temperature -30...+85 °C
• Connection: M12 connector, 4-pin

A yellow LED shows the switching state.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

ID5005 (IDE3060-FPKG) is an ifm rectangular inductive sensor with a 60 mm sensing range in a 105 x 80 x 40 mm housing. The sensing range is adjustable and the switching function (NO or NC) is selected on the unit.

• Sensing range: 60 mm ± 10 %, adjustable, operating distance 0...48.6 mm
• Output: PNP, NO/NC selectable, 250 mA, switching frequency 100 Hz
• Supply: 10...36 VDC, consumption 15 mA
• Protection: short-circuit, overload and reverse polarity
• Housing: rectangular, PPE, 105 x 80 x 40 mm, non-flush mounting
• Environment: IP65, operating temperature -25...+80 °C
• Connection: terminals up to 2.5 mm², M20 x 1.5 cable gland for cable Ø 7...13 mm

Correction factors (steel = 1): stainless steel 0.7, brass 0.4, aluminium 0.3, copper 0.2.

UL approved (Ta 0...40 °C, Type 1, file E174191). EMC to EN 55011 class B. MTTF 1277 years.

IFW200 (IFK3003BBPKG/K1/SC/US104) is an ifm inductive sensor for welding applications with a 3 mm sensing range and correction factor K = 1. Steel, stainless steel, brass, aluminium and copper are all detected at the same distance, and the sensor is immune to magnetic fields up to 300 mT.

• Sensing range: 3 mm ± 10 %, operating distance 0...2.4 mm, K = 1 for all metals
• Output: PNP, NO, 100 mA, switching frequency 2000 Hz
• Supply: 10...30 VDC, consumption < 20 mA; short-circuit, overload and reverse polarity protection
• Housing: M12 x 1, brass with anti-spatter coating, black LCP sensing face, length 65 mm, flush mountable
• Environment: IP67, operating temperature -25...+70 °C, magnetic field immunity 300 mT
• Connection: M12 connector, A-coded, 3-pin, gold-plated contacts

Used for part presence and position checks in welding cells and fixtures, where welding current fields and spatter would cause false switching on a standard sensor. Four yellow LEDs at 90° show the switching state from any side.

UL approved (file E174191). EMC to EN 55011 class B. MTTF 665 years.

NI30U-EM30WD-AP6X-H1141/3GD is a TURCK uprox+ inductive sensor for the food industry with a 30 mm rated switching distance. The housing is 1.4404 (AISI 316L) stainless steel with an LCP front cap and a double-lip seal, resistant to common acidic and alkaline cleaning agents. It is approved for ATEX category 3G and 3D, i.e. zone 2 (gas) and zone 22 (dust).

• Switching distance: 30 mm, non-flush mounting, factor 1 for all metals
• Output: PNP, NO, 3-wire, max. 200 mA; short-circuit, wire-break and reverse polarity protection, switching frequency 1 kHz
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M30 x 1.5 stainless steel 1.4404, thread length 31 mm, nut torque max. 75 Nm
• Environment: IP68 / IP69K, operating temperature -40...+100 °C
• Connection: M12 connector, 4-pin; SC-M12/3GD safety clip included

Used on washdown lines and filling or packaging machines where the sensor is cleaned in place with high-pressure water and chemicals. It can be screwed in up to the top of the thread, with the switching distance then reduced by 20 %. In an aperture plate keep a distance of 140 mm.

Marking: Ex II 3 G Ex ec IIC T4 Gc / Ex II 3 D Ex tc IIIC T110 °C Dc. MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

NI5-G12K-AP6X is a Turck inductive sensor in an M12 x 1 chrome-plated brass housing with a 5 mm switching distance for non-flush mounting.

• Sensing distance: 5 mm, non-flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: PNP, NO; up to 200 mA; switching frequency 1.5 kHz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: M12 x 1 thread, chrome-plated brass, PA12-GF30 sensing face, thread length 20 mm, nut torque up to 10 Nm
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: 2 m PVC cable (LifYY), 3 x 0.34 mm², Ø 5.2 mm

A yellow LED shows the switching state. Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

BI8U-EM18MWD-VP6X-H1141 is a TURCK uprox+ inductive sensor for the food industry with a 8 mm rated switching distance. The housing is 1.4404 (AISI 316L) stainless steel with an LCP front cap and a double-lip seal, resistant to common acidic and alkaline cleaning agents.

• Switching distance: 8 mm, flush mounting, factor 1 for all metals
• Output: PNP, complementary (NO + NC), 4-wire, max. 200 mA; short-circuit, wire-break and reverse polarity protection, switching frequency 1.5 kHz
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M18 x 1 stainless steel 1.4404, thread length 46 mm, LCP front cap rated to 15 bar, nut torque max. 25 Nm
• Environment: IP68 / IP69K, operating temperature -40...+100 °C
• Connection: M12 connector, 4-pin, PP connector housing

Used on washdown lines and filling or packaging machines where the sensor is cleaned in place with high-pressure water and chemicals. It can also be mounted recessed by half a turn of the thread.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

NI75U-CP80-VP4X2 is a TURCK uprox rectangular inductive sensor with a 75 mm switching distance in an 80 x 80 mm CP80 housing with terminals. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 75 mm, non-flush mounting
• Output: PNP, complementary (NO + NC), 4-wire, max. 200 mA; short-circuit, wire-break and reverse polarity protection, switching frequency 250 Hz
• Supply: 10...65 VDC, no-load current 15 mA
• Housing: rectangular CP80, 80 x 80 x 41 mm, PBT-GF30-V0
• Environment: IP67, operating temperature -30...+85 °C
• Connection: terminal chamber, conductors up to 2.5 mm²

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

NI3-M08E-AP6X-V1131 is a Turck inductive sensor in an M8 x 1 nickel-plated brass housing with an increased 3 mm switching distance for non-flush mounting.

• Sensing distance: 3 mm, non-flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: PNP, NO; up to 150 mA; switching frequency 2.8 kHz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: M8 x 1 thread, nickel-plated brass, PP-GF20 sensing face, thread length 36 mm, nut torque up to 7 Nm
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: M8 x 1 connector, 3-pin

A yellow LED shows the switching state. Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

BI5-M18-AN6X is a Turck inductive sensor in an M18 x 1 chrome-plated brass housing with a 5 mm switching distance for flush mounting.

• Sensing distance: 5 mm, flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: NPN, NO; up to 200 mA; switching frequency 500 Hz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: M18 x 1 thread, chrome-plated brass, PA12-GF30 sensing face, thread length 45 mm, nut torque up to 25 Nm
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: 2 m PVC cable (LifYY), 3 x 0.34 mm², Ø 5.2 mm

A yellow LED shows the switching state. Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

BI10U-M18-VN6X is a TURCK uprox3 inductive sensor with an extended 10 mm switching distance in an M18 housing. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 10 mm, flush mounting
• Output: NPN, complementary (NO + NC), 4-wire, max. 200 mA, switching frequency 1.5 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M18 x 1 chrome-plated brass, LCP sensing face, thread length 45 mm, nut torque max. 10 Nm
• Environment: IP68, operating temperature -25...+70 °C
• Connection: 2 m PVC cable, 4 x 0.34 mm², Ø 5.2 mm

A yellow LED shows the switching state.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

BI2-Q10S-VP6X is a Turck inductive sensor in a flat rectangular Q10S housing, 10.2 mm high, with the sensing face on the side. Its complementary PNP output switches one NO and one NC signal at the same time.

• Sensing distance: 2 mm, flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: PNP, complementary (NO + NC); up to 150 mA; switching frequency 2 kHz
• Supply: 10...30 VDC, 4-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: Q10S, 27.8 x 16 x 10.2 mm, PP-GF20 plastic, lateral sensing face
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: 2 m PUR cable (Lif9Y-11YFHF), 4 x 0.14 mm², Ø 3 mm

A yellow LED shows the switching state. Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

NI12U-EM18-AP6X/3D is a TURCK uprox inductive sensor in a stainless steel M18 housing, approved for ATEX zone 22. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 12 mm, non-flush mounting, partially embeddable
• Output: PNP, NO, 3-wire, max. 200 mA, switching frequency 2 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M18 x 1 stainless steel 1.4301, PBT sensing face, thread length 35 mm, nut torque max. 25 Nm
• Environment: IP68, operating temperature -30...+85 °C (-25...+70 °C in the Ex zone)
• Connection: 2 m PVC cable, 3 x 0.34 mm², Ø 5.2 mm

Used where combustible dust may be present, such as silos, mills and feed lines. Auto-compensation protects the sensor against pre-damping by the mounting. A yellow LED shows the switching state.

ATEX II 3 D Ex tD A22 IP67 T110 °C. MTTF 874 years (SN 29500, 40 °C).

NI5-Q18-AN6X is a Turck inductive sensor in a rectangular Q18 plastic housing with a 5 mm switching distance for non-flush mounting.

• Sensing distance: 5 mm, non-flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: NPN, NO; up to 200 mA; switching frequency 500 Hz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: Q18, 29 x 18 x 18 mm, sensing face in front, PBT-GF30-V0 plastic, PBT-GF30-V0 sensing face
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: 2 m PVC cable (LifYY), 3 x 0.34 mm², Ø 5.2 mm

A yellow LED shows the switching state. Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

BI3-M08E-AP6X-V1131 is a Turck inductive sensor in an M8 x 1 nickel-plated brass housing with an increased 3 mm switching distance for flush mounting.

• Sensing distance: 3 mm, flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: PNP, NO; up to 150 mA; switching frequency 2.8 kHz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: M8 x 1 thread, nickel-plated brass, PP-GF20 sensing face, thread length 40 mm, nut torque up to 7 Nm
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: M8 x 1 connector, 3-pin

A yellow LED shows the switching state. Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

NI4-DSU26-2AP4X2-H1141 is a Turck dual inductive sensor in a DSU26 housing for position monitoring of rotary actuators. Two PNP NO outputs signal the two end positions, and the housing mounts on standard actuators.

• Sensing distance: 4 mm, non-flush mounting
• Outputs: 2 x PNP, NO; up to 200 mA each; switching frequency 50 Hz
• Supply: 10...65 VDC, 4-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: DSU26, 68 x 60 x 35.4 mm, yellow PP-GF30 plastic, black PP-GF30 sensing face
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: M12 x 1 connector, 4-pin

The sensor detects the end positions through an actuation puck on the actuator shaft (Turck BTS-DSC26 series), which is ordered separately. Two LEDs (yellow/red) show the switching state.

Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

NI20-CP40-FZ3X2 is a TURCK rectangular inductive sensor with a 20 mm switching distance and a 2-wire AC/DC output that runs on 20...250 VAC or 10...300 VDC. The switching function (NO or NC) is set by how the sensor is wired.

• Switching distance: 20 mm, non-flush mounting
• Output: 2-wire AC/DC, NO/NC programmable by wiring; max. 400 mA AC / 300 mA DC, residual current ≤ 1.7 mA, switching frequency 20 Hz
• Supply: 20...250 VAC (50...60 Hz) or 10...300 VDC, voltage drop ≤ 6 V
• Housing: rectangular CP40, 114 x 40 x 40 mm, PBT-GF30-V0
• Environment: IP67, operating temperature -25...+70 °C
• Connection: terminal chamber, conductors up to 2.5 mm², M20 x 1.5 cable entry

The sensing head turns to 9 positions, and two green and two red corner LEDs show power and switching state from any side. The output has no short-circuit protection: minimum load current is 3 mA and surge current must stay ≤ 8 A (10 ms).

Correction factors (St37 = 1): stainless steel 0.7, brass 0.4, aluminium 0.3. MTTF 2283 years (SN 29500, 40 °C).

BI6U-M12-VP6X-H1141 is a TURCK uprox3 inductive sensor. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 6 mm, flush mounting
• Output: PNP, complementary (NO + NC), 4-wire, max. 200 mA, switching frequency 2 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M12 x 1 chrome-plated brass, LCP sensing face, thread length 36 mm, nut torque max. 7 Nm
• Environment: IP68, operating temperature -25...+70 °C
• Connection: M12 connector, 4-pin

A yellow LED shows the switching state.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

IR18.D08L-Q60.IA1E.7BO is a Baumer linearised inductive distance sensor with a 0...8 mm measuring range and a 4...20 mA output. The characteristic can be adjusted by external teach-in: 1-point or 2-point analogue teach, or a reset to factory setting.

• Accuracy: linearity error ±32 µm, repeatability 0.015 mm, temperature drift ±4 % FS
• Measuring range: 0...8 mm, sensitivity 2.0 mA/mm, resolution < 0.002 mm static, < 0.006 mm dynamic
• Output: current 4...20 mA, linear, response time < 1 ms
• Supply: 12...36 VDC, consumption max. 20 mA; short-circuit and reverse polarity protection
• Housing: M18 x 1 nickel-plated brass, PBT sensing face, length 60 mm, quasi-flush mounting, tightening torque max. 40 Nm
• Environment: IP67, operating temperature -25...+75 °C
• Connection: M12 connector, 5-pin (teach-in on pins 2 and 5)

Teach-in runs over the teach wire, so the analogue range can be matched to the actual target travel on the machine without software. A yellow LED confirms the teach.

BI8U-EM18WD-VP6X-H1141/3GD is a TURCK uprox inductive sensor for the food industry, in a stainless steel 1.4404 housing with an LCP front cap, approved for ATEX zones 2 and 22. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 8 mm, flush mounting
• Output: PNP, complementary (NO + NC), 4-wire, max. 200 mA, switching frequency 1.5 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M18 x 1 stainless steel 1.4404 (AISI 316L), LCP front cap rated to 15 bar, thread length 36 mm, nut torque max. 25 Nm
• Environment: IP68 / IP69K, operating temperature -40...+100 °C
• Connection: M12 connector, 4-pin

Used on washdown lines where sensors are cleaned with high-pressure water and alkaline agents, including areas classed as zone 2 or zone 22. A yellow LED shows the switching state.

ATEX II 3 G Ex ec IIC T4 Gc / II 3 D Ex tc IIIC T110 °C Dc. MTTF 874 years (SN 29500, 40 °C).

BI10U-M18-AP6X is a TURCK uprox3 inductive sensor with an extended 10 mm switching distance in an M18 housing. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 10 mm, flush mounting
• Output: PNP, NO, 3-wire, max. 200 mA, switching frequency 1.5 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M18 x 1 chrome-plated brass, LCP sensing face, thread length 45 mm, nut torque max. 10 Nm
• Environment: IP68, operating temperature -25...+70 °C
• Connection: 2 m PVC cable, 3 x 0.34 mm², Ø 5.2 mm

A yellow LED shows the switching state.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

ID0013 (IDE2060-FBOA) is an ifm rectangular inductive sensor with a 60 mm sensing range in a 105 x 80 x 40 mm housing. The sensing range is adjustable and the switching function (NO or NC) is selected on the unit.

• Sensing range: 60 mm ± 10 %, adjustable, operating distance 0...48.6 mm
• Output: 2-wire AC/DC, NO/NC selectable; 250 mA AC (350 mA up to 50 °C), 100 mA DC, switching frequency 4 Hz
• Supply: 20...250 V AC/DC
• Protection: no short-circuit or overload protection; fit a fast-acting miniature fuse ≤ 2 A to IEC 60127-2
• Housing: rectangular, PPE, 105 x 80 x 40 mm, non-flush mounting
• Environment: IP65, operating temperature -25...+80 °C
• Connection: terminals up to 2.5 mm², M20 x 1.5 cable gland for cable Ø 7...13 mm

Correction factors (steel = 1): stainless steel 0.7, brass 0.4, aluminium 0.3, copper 0.2.

UL approved (Ta 0...40 °C, Type 1, file E174191). EMC to EN 55011 class B. MTTF 460 years.

NI12U-M18E-AP6X-H1141 is a TURCK uprox inductive sensor with an extended 12 mm switching distance in a long M18 housing. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 12 mm, non-flush mounting
• Output: PNP, NO, 3-wire, max. 200 mA, switching frequency 1 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M18 x 1 chrome-plated brass, PBT sensing face, thread length 46 mm, nut torque max. 25 Nm
• Environment: IP68, operating temperature -30...+85 °C
• Connection: M12 connector, 4-pin

A yellow LED shows the switching state.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

IGYX 12N17B1/S14L is a Baumer inductive proximity sensor in an M12 barrel with a 4 mm nominal sensing distance and a NPN normally open (NO) output. The sensing face is flush mountable and the nickel-plated brass housing is 60 mm long.

• Sensing distance: 4 mm (Sn), assured 3.2 mm (Sa)
• Output: NPN, normally open (NO), 200 mA, with short-circuit and reverse-polarity protection
• Supply: 10...30 V DC, current consumption up to 15 mA with no load
• Housing: M12 thread, nickel-plated brass, PBT sensing face, 60 mm long, flush mountable
• Environment: IP 67, operating temperature -25...+75 °C
• Connection: M12 connector

The sensor is intended for presence and end-position monitoring of metal parts on conveyors, pneumatic cylinders and indexing mechanisms. Switching frequency is 1.5 kHz. Tightening torque on the M12 thread must not exceed 10 Nm, and the switching point drifts by up to ±10 % of Sr across the temperature range, which matters when the target sits close to the 4 mm limit.

Complies with the EMC requirements of EN 60947-5-2:2007.

IGYX 12P17B1/S14L is a Baumer inductive proximity sensor in an M12 barrel with a 4 mm nominal sensing distance and a PNP normally open (NO) output. The sensing face is flush mountable and the nickel-plated brass housing is 60 mm long.

• Sensing distance: 4 mm (Sn), assured 3.2 mm (Sa)
• Output: PNP, normally open (NO), <200 mA, with short-circuit and reverse-polarity protection
• Supply: 10...30 V DC, current consumption up to 15 mA with no load
• Housing: M12 thread, nickel-plated brass, PBT sensing face, 60 mm long, flush mountable
• Environment: IP 67, operating temperature -25...+75 °C
• Connection: M12 connector

The sensor is intended for presence and end-position monitoring of metal parts on conveyors, pneumatic cylinders and indexing mechanisms. Switching frequency is <1.5 kHz. Tightening torque on the M12 thread must not exceed 10 Nm, and the switching point drifts by up to ±10 % of Sr across the temperature range, which matters when the target sits close to the 4 mm limit.

Complies with the EMC requirements of EN 60947-5-2:2007.

BI10-P30-Y1X is a Turck inductive sensor with a NAMUR output to EN 60947-5-6 in an M30 plastic housing, approved for explosion-hazardous areas up to zone 1 (gas) and zone 20 (dust).

• Sensing distance: 10 mm, flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: NAMUR, 2-wire; current ≥ 2.1 mA not actuated, ≤ 1.2 mA actuated; switching frequency 500 Hz
• Supply: nominal 8.2 VDC; Ci/Li 150 nF / 150 µH
• Housing: M30 x 1.5 thread, thread length 40 mm, PA12-GF30 plastic, nut torque up to 5 Nm
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: 2 m blue PVC cable (LiYY), 2 x 0.5 mm², Ø 5.2 mm

The sensor may only be connected to certified intrinsically safe (Ex i) circuits, for example an isolating switching amplifier with a NAMUR input. Maximum input values: Ui = 20 V, Ii = 20 mA, Pi = 200 mW. A yellow LED shows the switching state.

Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

Marking Ex II 2 G Ex ia IIC T6 Gb / II 1 D Ex ia IIIC T135 °C Da, certificate KEMA 02 ATEX 1090X. SIL2 (low demand) acc. to IEC 61508 and PL c acc. to ISO 13849-1 with HFT0; SIL3 and PL e in redundant configuration with HFT1. MTTF 6198 years acc. to SN 29500 (40 °C).

IGYX 08P37B3/S35L is a Baumer inductive proximity sensor in an M8 barrel with a 2 mm nominal sensing distance and a PNP normally closed (NC) output. The sensing face is flush mountable and the stainless steel housing is 36 mm long.

• Sensing distance: 2 mm (Sn), assured 1.6 mm (Sa)
• Output: PNP, normally closed (NC), 200 mA, with short-circuit and reverse-polarity protection
• Supply: 10...30 V DC, current consumption up to 15 mA with no load
• Housing: M8 thread, stainless steel, PBT sensing face, 36 mm long, flush mountable
• Environment: IP 67, operating temperature -25...+75 °C
• Connection: M8 connector

The Ø 8 mm body and 36 mm length fit the sensor into grippers, indexing tables and other positions where an M12 barrel does not fit. A 3 kHz switching frequency is enough for presence monitoring of fast moving metal parts. Tightening torque on the M8 thread must not exceed 5 Nm, and the switching point drifts by up to ±10 % of Sr across the temperature range, which matters when the target sits close to the 2 mm limit.

Complies with the EMC requirements of EN 60947-5-2:2007.

NI30U-EM30WD-AP6X is a TURCK uprox+ inductive sensor for the food industry with a 30 mm rated switching distance. The housing is 1.4404 (AISI 316L) stainless steel with an LCP front cap and a double-lip seal, resistant to common acidic and alkaline cleaning agents.

• Switching distance: 30 mm, non-flush mounting, factor 1 for all metals
• Output: PNP, NO, 3-wire, max. 200 mA; short-circuit, wire-break and reverse polarity protection, switching frequency 1 kHz
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M30 x 1.5 stainless steel 1.4404, thread length 36 mm, nut torque max. 75 Nm
• Environment: IP68 / IP69K, operating temperature -40...+100 °C
• Connection: 2 m PP cable, 3 x 0.34 mm², Ø 5.2 mm, transparent PP end cap

Used on washdown lines and filling or packaging machines where the sensor is cleaned in place with high-pressure water and chemicals. It can be screwed in up to the top of the thread, with the switching distance then reduced by 20 %. In an aperture plate keep a distance of 140 mm.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

BI2-G12K-AP6X is a Turck inductive sensor in an M12 x 1 chrome-plated brass housing with a 2 mm switching distance for flush mounting.

• Sensing distance: 2 mm, flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: PNP, NO; up to 200 mA; switching frequency 2 kHz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: M12 x 1 thread, chrome-plated brass, PA12-GF30 sensing face, thread length 30 mm, nut torque up to 10 Nm
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: 2 m PVC cable (LifYY), 3 x 0.34 mm², Ø 5.2 mm

A yellow LED shows the switching state. Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

BI3-M08-AP6X-V1131 is a Turck inductive sensor in an M8 x 1 nickel-plated brass housing with an increased 3 mm switching distance for flush mounting.

• Sensing distance: 3 mm, flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: PNP, NO; up to 150 mA; switching frequency 2.8 kHz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: M8 x 1 thread, nickel-plated brass, PP-GF20 sensing face, thread length 30 mm, nut torque up to 7 Nm
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: M8 x 1 connector, 3-pin

A yellow LED shows the switching state. Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

NI3-M08-AP6X-V1131 is a Turck inductive sensor in an M8 x 1 nickel-plated brass housing with a 3 mm switching distance for non-flush mounting.

• Sensing distance: 3 mm, non-flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: PNP, NO; up to 150 mA; switching frequency 2.8 kHz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: M8 x 1 thread, nickel-plated brass, PP-GF20 sensing face, thread length 26 mm, nut torque up to 7 Nm
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: M8 x 1 connector, 3-pin

A yellow LED shows the switching state. Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

BI10-EM30-AP6/S907 is a Turck inductive sensor in an M30 x 1.5 stainless steel housing with a 10 mm switching distance for flush mounting. The S907 version with FEP-jacketed cable is rated for ambient temperatures up to +160 °C.

• Temperature: ambient up to +160 °C (special version S907), range -25...+160 °C; IP68, IP69K
• Sensing distance: 10 mm, flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: PNP, NO; up to 200 mA; switching frequency 200 Hz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: M30 x 1.5 thread, stainless steel 1.4571 (AISI 316Ti), PEEK sensing face, thread length 65 mm, PTFE end cap, nut torque up to 40 Nm; front cap withstands ≤ 10 bar
• Connection: 2 m FEP cable (PTFE), 3 x 0.34 mm², Ø 3.7 mm

The permissible output current falls at higher ambient temperatures - see the derating curve in the datasheet.

Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

BI10U-M18-IOL6X2-H1141 is a TURCK uprox3 inductive sensor with IO-Link, in an M18 housing with an extended 10 mm switching distance. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 10 mm, flush mounting
• Output: pin 4 switching output or IO-Link, PNP/NPN and NO/NC configurable, max. 150 mA, switching frequency 0.5 kHz; pin 2 digital input
• IO-Link: V1.1, port class A, COM 2 (38.4 kBaud), 16-bit process data, min. cycle time 8 ms
• Supply: 10...30 VDC, no-load current 27 mA
• Housing: M18 x 1 chrome-plated brass, LCP sensing face, thread length 36 mm, nut torque max. 25 Nm
• Environment: IP68, operating temperature -25...+70 °C
• Connection: M12 connector, 4-pin

Over IO-Link the switching distance, hysteresis, output logic and timer functions can be set from the master, and the device is identified through a 32-byte memory. A yellow LED shows the switching state.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

NI15U-EM18WD-AP6X-H1141 is a TURCK uprox+ inductive sensor for the food industry with a 15 mm rated switching distance. The housing is 1.4404 (AISI 316L) stainless steel with an LCP front cap and a double-lip seal, resistant to common acidic and alkaline cleaning agents.

• Switching distance: 15 mm, non-flush mounting, factor 1 for all metals
• Output: PNP, NO, 3-wire, max. 200 mA; short-circuit, wire-break and reverse polarity protection, switching frequency 1 kHz
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M18 x 1 stainless steel 1.4404, thread length 26 mm, nut torque max. 25 Nm
• Environment: IP68 / IP69K, operating temperature -40...+100 °C
• Connection: M12 connector, 4-pin

Used on washdown lines and filling or packaging machines where the sensor is cleaned in place with high-pressure water and chemicals. It can be screwed in up to the top of the thread, with the switching distance then reduced by 20 %. In an aperture plate keep a distance of 70 mm.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

BI5U-EG18SK-AP6X is a TURCK uprox inductive sensor in a stainless steel M18 housing with a terminal chamber. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 5 mm, flush mounting
• Output: PNP, NO, 3-wire, max. 200 mA, switching frequency 2.5 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M18 x 1 stainless steel 1.4301, PBT sensing face, PA12-GF30 terminal chamber, thread length 45 mm, nut torque max. 25 Nm
• Environment: IP67, operating temperature -30...+85 °C
• Connection: terminal chamber, conductors up to 2.5 mm², cable Ø 4.5...8 mm; cable gland and 2 rubber seals included

The cable is wired on site to the required length, with no separate cordset or junction box. A yellow LED shows the switching state.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

NI10-G18SK-AP6X is a Turck inductive sensor in an M18 x 1 chrome-plated brass housing with a 10 mm switching distance for non-flush mounting. Wires connect directly to terminals in the sensor's terminal chamber, so no cordset is needed.

• Sensing distance: 10 mm, non-flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: PNP, NO; up to 200 mA; switching frequency 500 Hz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: M18 x 1 thread, chrome-plated brass, PA12-GF30 sensing face, thread length 35 mm, nut torque up to 25 Nm
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: terminal chamber

A yellow LED shows the switching state. Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

BID2-G180-AP6/S212 is a TURCK pressure-resistant inductive sensor in a stainless steel M18 housing. The sensing face withstands 500 bar static and 350 bar dynamic pressure, so it can sit directly in a hydraulic cylinder or valve.

• Switching distance: 2 mm, flush mounting; correction factors steel 1, stainless steel 0.7, brass 0.4, aluminium 0.3
• Output: PNP, NO, 3-wire, max. 200 mA, switching frequency 2 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 15 mA
• Housing: M18 x 1 stainless steel 1.4305, PA12-GF30 sensing face, thread length 29 mm, nut torque max. 25 Nm
• Environment: IP67, operating temperature -25...+85 °C
• Connection: 2 m Ölflex cable, 3 x 0.5 mm², Ø 6.3 mm

Typical use is end-position detection of a piston inside a hydraulic cylinder.

MTTF 1804 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

NI3-EG08K-AP6X-V1131 is a Turck inductive sensor in an M8 x 1 stainless steel housing with a 3 mm switching distance for non-flush mounting.

• Sensing distance: 3 mm, non-flush mounting; secured operating distance ≤ 0.81 × Sn
• Output: PNP, NO; up to 150 mA; switching frequency 3 kHz
• Supply: 10...30 VDC, 3-wire, no-load current 15 mA, voltage drop ≤ 1.8 V
• Protection: short circuit, wire break and reverse polarity
• Housing: M8 x 1 thread, stainless steel 1.4305 (AISI 303), PBT sensing face, thread length 16.5 mm, nut torque up to 5 Nm
• Environment: IP67, ambient temperature -25...+70 °C
• Connection: M8 x 1 connector, 3-pin

A yellow LED shows the switching state. Correction factors for other target metals (St37 steel = 1): aluminium 0.3, brass 0.4, stainless steel 0.7.

MTTF 2283 years acc. to SN 29500 (40 °C).

BI8U-M18E-AP6X-H1141 is a TURCK uprox inductive sensor with an extended 8 mm switching distance in a long M18 housing. Correction factor 1 for all metals and immune to magnetic AC and DC fields up to 300 mT, so steel, stainless steel, aluminium and brass are detected at the same distance.

• Switching distance: 8 mm, flush mounting
• Output: PNP, NO, 3-wire, max. 200 mA, switching frequency 1.5 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 25 mA
• Housing: M18 x 1 chrome-plated brass, LCP sensing face, thread length 56 mm, nut torque max. 25 Nm
• Environment: IP68, operating temperature -30...+85 °C
• Connection: M12 connector, 4-pin

A yellow LED shows the switching state.

MTTF 874 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).

BI3-M08E-VP6X-V1141 is a TURCK inductive sensor with an extended 3 mm switching distance in a flush-mounted M8 housing. Correction factors: steel St37 = 1, stainless steel 0.7, brass 0.4, aluminium 0.3, so non-ferrous targets are detected at a shorter distance.

• Switching distance: 3 mm, flush mounting
• Output: PNP, complementary (NO + NC), 4-wire, max. 150 mA, switching frequency 2.8 kHz; short-circuit, wire-break and reverse polarity protection
• Supply: 10...30 VDC, no-load current 15 mA
• Housing: M8 x 1 nickel-plated brass, PP-GF20 sensing face, thread length 40 mm, nut torque max. 7 Nm
• Environment: IP67, operating temperature -25...+70 °C
• Connection: M8 connector, 4-pin

MTTF 2283 years (SN 29500, 40 °C). Shock 30 g (11 ms), vibration 55 Hz (1 mm).