SMB30A is a Banner right-angle bracket for sensors with a 30 mm housing. The curved slot lets the sensor be turned before the screws are tightened.

• Sensor hole: Ø30.5 mm
• Mounting: M6 (¼") hardware, 40 mm hole centre spacing
• Material: 12-gauge stainless steel

IN5-18HTPS-180 is an M18 inductive proximity sensor for ambient temperatures up to +180 °C, with a 5 mm sensing distance for flush mounting and a PNP normally open (NO) output. The housing has no switching LED.

• Sensing distance: 5 mm (±10 %), flush mounting; standard target 18 x 18 x 1 mm, ST37 steel
• Output: PNP, NO; load current 120 mA, short-circuit limit 200 mA; switching frequency 400 Hz
• Supply: 10...35 VDC, 3-wire; voltage drop approx. 2 V when switched on; reverse polarity protection
• Housing: M18x1 thread, sensing face Vectra LCP
• Environment: IP67, operating temperature -40...+180 °C, relative humidity up to 100 %
• Connection: 5 m silicone cable, 3 x 0.25 mm²

EMC immunity: IEC 61000-4-2, IEC 61000-4-3 and IEC 61000-4-4 level 2, IEC 60255-5 1 kV. Vibration 1 mm amplitude at 55 Hz, shock 10 g for 11 ms.

SI18-CE8 PNP NO H is an AECO M18 inductive sensor with an 8 mm sensing distance for non-flush mounting and a PNP normally open (NO) output. Four LEDs around the connector end show the switching state.

• Sensing distance: 8 mm, non-flush mounting; hysteresis < 10 %, repeatability ≤ 3 %
• Output: PNP, NO; up to 200 mA, voltage drop < 1.8 V; switching frequency 1000 Hz
• Supply: 10...30 VDC, 3-wire, current consumption < 15 mA at 24 VDC; short-circuit protection
• Housing: M18x1, nickel-plated brass, length 70 mm plus 10.5 mm sensing head
• Environment: operating temperature -25...+85 °C; IP rating depends on the mating connector
• Connection: H plug - M12 connector, 4-pin male (pins 1, 3, 4 used); cable ordered separately

For non-flush mounting, keep a metal-free zone of at least the sensor diameter on each side of the sensing head and 2 diameters between two sensors side by side.

SI18-DC8 PNP NO H is an AECO M18 inductive sensor with an 8 mm sensing distance for flush mounting and a PNP normally open (NO) output. Four LEDs around the connector end show the switching state.

• Sensing distance: 8 mm, flush mounting; hysteresis < 10 %, repeatability ≤ 3 %
• Output: PNP, NO; up to 200 mA, voltage drop < 1.8 V; switching frequency 400 Hz
• Supply: 10...30 VDC, 3-wire, current consumption < 15 mA at 24 VDC; short-circuit protection
• Housing: M18x1, nickel-plated brass, length 71 mm
• Environment: operating temperature -25...+85 °C; IP rating depends on the mating connector
• Connection: H plug - M12 connector, 4-pin male (pins 1, 3, 4 used); cable ordered separately

Two sensors mounted side by side need at least half the sensor diameter between them.

IS-30-A15-03 is a Datalogic (Datasensing) M30 inductive sensor for 20...250 VAC supply, with a 10 mm sensing distance for flush mounting. The normally open (NO) output is an SCR on two wires; a yellow LED shows the output state.

• Sensing distance: 10 mm, flush mounting; operating distance 0...8.1 mm, standard target 30 x 30 mm FE360
• Output: SCR, NO, 2-wire; load 20...500 mA (inrush 1.5 A), residual current < 0.7 mA, voltage drop ≤ 4 V at 100 mA; switching frequency 25 Hz
• Supply: 20...250 VAC, 50/60 Hz; start-up delay < 300 ms
• Protection: short circuit (self-resetting), inductive loads
• Housing: M30x1.5, nickel-plated brass, length 56 mm, PA16 sensing face, tightening torque max. 40 Nm; 2 M30x1.5 nuts included
• Environment: IP67, operating temperature -25...+70 °C
• Connection: 2 m PVC cable, 2 x 0.25 mm²

Approvals: CE, cULus.

SI12-AE4 NO is an AECO M12 inductive sensor for 20...250 VAC supply, with a 4 mm sensing distance for non-flush mounting and a normally open (NO) output on two wires. An LED shows the output state.

• Sensing distance: 4 mm, non-flush mounting; hysteresis < 10 %, repeatability ≤ 3 %
• Output: NO, 2-wire; load 5...300 mA (peak 1.5 A for 20 ms), residual current < 1 mA, voltage drop < 6 V; switching frequency 12 Hz
• Supply: 20...250 VAC
• Housing: M12x1, nickel-plated brass, length 60 mm plus 7.5 mm sensing head
• Environment: IP67, operating temperature -25...+70 °C
• Connection: 2 m PVC cable, 2 x 0.25 mm²

SI18-A5 NO is an AECO M18 inductive sensor for 20...250 VAC supply, with a 5 mm sensing distance for flush mounting and a normally open (NO) output on two wires. A yellow LED shows the output state.

• Sensing distance: 5 mm, flush mounting; operating distance 0...4.05 mm, hysteresis < 10 %, repeatability < 3 %
• Output: NO, 2-wire; load 5...300 mA (peak 1.5 A), residual current < 1 mA, voltage drop < 6 V; switching frequency 12 Hz
• Supply: 20...250 VAC
• Housing: M18x1, nickel-plated brass, length 65 mm, blue POM sensing face, nickel-plated brass nuts
• Environment: IP65, IP66, IP67, operating temperature -25...+70 °C
• Connection: 2 m PVC/PVC cable, 2 x 0.50 mm²

Correction factors for other target metals: stainless steel 0.9, brass 0.5, aluminium 0.4, copper 0.4.

Complies with the EMC directive 2014/30/EU and the low voltage directive 2014/35/EU; product standard EN 60947-5-2.

PFI25-8DP is an Autonics flat-type inductive sensor with a 25 mm sensing face on the top side and an 8 mm sensing distance. The PNP output is normally open (NO); a red LED shows the operating state.

• Sensing distance: 8 mm, setting distance 0...5.6 mm; standard target 25 x 25 x 1 mm iron, hysteresis ≤ 10 %
• Output: PNP, NO; up to 200 mA, residual voltage ≤ 1.5 V; response frequency 200 Hz
• Supply: 12-24 VDC (operating range 10...30 VDC), 3-wire, current consumption ≤ 10 mA
• Protection: surge, reverse polarity, output short circuit and overcurrent
• Housing: PPS, sensing face on the top side; 2 x M3 bolts included
• Environment: IP67, operating temperature -25...+70 °C, humidity 35...95 % RH
• Connection: 2 m PVC cable, Ø 4 mm, 3 cores AWG 22

Two sensors side by side need at least 80 mm between them, face to face at least 100 mm, to avoid mutual interference. Tighten the M3 mounting screws to no more than 1.47 Nm.

SI12SM-BE4 NO/NC is an AECO M12 inductive sensor for 10...55 VDC with a 4 mm sensing distance for non-flush mounting. The 2-wire output is programmable as NO or NC; a yellow LED shows the output state.

• Sensing distance: 4 mm, non-flush mounting; operating distance 0...3.24 mm, hysteresis < 10 %, repeatability < 3 %
• Output: 2-wire, NO/NC programmable; load 1.5...100 mA, residual current < 0.6 mA, voltage drop < 6.5 V; switching frequency 1000 Hz
• Supply: 10...55 VDC
• Protection: reverse polarity, short circuit (pulsed), overload
• Housing: M12x1, nickel-plated brass, length 67.5 mm, red POM sensing face, nickel-plated brass nuts
• Environment: IP65, IP66, IP67, operating temperature -25...+70 °C
• Connection: 2 m PVC/PVC cable, 2 x 0.25 mm²

Correction factors for other target metals: stainless steel 0.9, brass 0.5, aluminium 0.4, copper 0.4.

Complies with the EMC directive 2014/30/EU; product standard EN 60947-5-2.

IPS40-N40PCOL-PG13 is an XECRO inductive sensor in a 40 x 40 mm PBT housing with extended sensing range: 40 mm for non-flush mounting. The PNP output has a normally open and a normally closed contact at the same time; the wires go to terminals through a PG13.5 cable gland.

• Sensing distance: 40 mm (extended range), non-flush mounting
• Output: PNP, NO + NC; load up to 200 mA, voltage drop < 2 V at 200 mA; switching frequency 120 Hz
• Supply: 10...30 VDC, current consumption < 11 mA
• Protection: reverse polarity, short circuit (self-resetting)
• Housing: 40 x 40 mm, PBT, PBT sensing face
• Environment: IP67, operating temperature -20...+70 °C
• Connection: terminals, PG13.5 cable gland

Reduction factors for other target metals: aluminium 0.45, brass 0.50, stainless steel 0.85.

SMB30FA is a Banner swivel bracket for 30 mm barrel sensors. The clamp tilts and pans on a 3/8-16 bolt, so the sensor can be aimed after the bracket is fixed.

• Fits: sensors with M30 thread, Ø 30.1 mm clamp hole
• Movement: tilt and pan, locked with a 10-24 clamp screw
• Mounting: 3/8-16 UNC bolt
• Material: stainless steel

237-7255 is an RS PRO M18 inductive sensor with IO-Link V1.1, the long-housing flush version with an 8 mm sensing distance and a 2 m cable. Output type, NO or NC function and sensing distance are set over IO-Link; without a master it works as a standard PNP NO switch.

• Sensing distance: 8 mm, flush mounting; settable over IO-Link to 33, 50, 75 or 100 % (factory 100 %), hysteresis standard or increased
• Output: PNP, NPN or push-pull, NO or NC (factory setting PNP NO); up to 200 mA, voltage drop max. 2.5 V at 200 mA; switching frequency up to 1.5 kHz; IO-Link V1.1
• Supply: 10...36 VDC, 3-wire, no-load current ≤ 20 mA
• Protection: short circuit, reverse polarity, transients
• Housing: M18x1, nickel-plated brass, grey thermoplastic polyester front cap, tightening torque max. 25 Nm
• Environment: IP67, operating temperature -25...+70 °C
• Connection: 2 m PVC cable, 3 x 0.25 mm², Ø 4.1 mm, oil-resistant

The yellow LED shows the output state and flashes at 2 Hz on short circuit or overload; the green LED shows that the sensor is operational. A temperature alarm can be enabled over IO-Link, and both LEDs can be switched off.

Designed to EN 60947-5-2 and EN 60947-1; UL 508 approval. Vibration per IEC 60068-2-6 (10...55 Hz, 1 mm), shock per IEC 60068-2-27 (30 g, 11 ms). MTTFd 3945 years at 50 °C.

IGYX 30P17B3/S14L is a Baumer inductive proximity sensor in an M30 barrel with a 15 mm nominal sensing distance and a PNP normally open (NO) output. The sensing face is flush mountable and the nickel-plated brass housing is 60 mm long.

• Sensing distance: 15 mm (Sn), assured 12 mm (Sa)
• Output: PNP, normally open (NO), 200 mA, with short-circuit and reverse-polarity protection
• Supply: 10...30 V DC, current consumption up to 15 mA with no load
• Housing: M30 thread, nickel-plated brass, PBT sensing face, 60 mm long, flush mountable
• Environment: IP 67, operating temperature -25...+75 °C
• Connection: M12 connector

The 15 mm sensing distance keeps the sensor clear of the moving part - end-position monitoring on hydraulic and pneumatic cylinders, gates and pallets. Switching frequency is 400 Hz, so this model is not suited to counting the teeth of a fast rotating gear. Tightening torque on the M30 thread must not exceed 60 Nm, and the switching point drifts by up to ±10 % of Sr across the temperature range, which matters when the target sits close to the 15 mm limit.

Complies with the EMC requirements of EN 60947-5-2:2007.