O300.RP.T-GW1J.72N is a Baumer O300 series retro-reflective photoelectric sensor for detecting transparent objects - glass and PET bottles, film and clear packaging - at up to 3.5 m. Switching is triggered by the attenuation of the returned signal, and the threshold can be set to 10, 20 or 30 %, so the sensor also responds to an object that weakens the signal only partly.

• Range: 3.5 m actual, 4 m nominal, with polarisation filter
• Signal attenuation threshold: 10 %, 20 % or 30 %
• Output: push-pull, light / dark operate, 100 mA
• Communication: IO-Link V1.1, filter functions, qTeach lock
• Supply: 10...30 V DC, typical consumption 30 mA
• Environment: IP 67, -30...+60 °C
• Connection: M8 connector, 4 pin

The sensor suits checks on empty glass and PET bottles, film and clear packaging on filling and packaging lines. The attenuation threshold and the filter functions can be changed over IO-Link from the control system, while qTeach can be locked so that the settings cannot be overwritten by accident.

OR18.SP-GW1B.7BO is a Baumer M18 SmartReflect light barrier that works against a fixed background at 55...300 mm instead of a separate reflector. The sensor is taught to the background position and switches when an object interrupts the beam in front of it, at up to 85-90 % of the background distance. Teaching is done with qTeach on the housing or through the external teach input.

• Background position: 55...300 mm; detection range 85-90 % of the background distance; red PinPoint LED 630 nm
• Output: push-pull, max. 100 mA, light/dark operate; response time < 0.49 ms
• Supply: 10...30 V DC, max. 45 mA
• Housing: M18 x 1 threaded, 65 mm long, nickel-plated brass, PA lens
• Environment: IP67; -25...+60 °C
• Connection: M12 4-pin connector

Suited to positions where a machine part, guide or conveyor belt sits behind the object and no reflector can be mounted. The push-pull output works with both PNP and NPN controller inputs. Pin 2 (white) is the teach input, so the sensor can be re-taught from the controller after a changeover.

O300W.GP-GW1J.PVN is a Baumer O300W series photoelectric sensor with background suppression and a 30...200 mm switching distance in a 1.4404 (V4A) stainless steel housing. The housing meets IP 68/69K and proTect+ and carries Ecolab approval, so the sensor does not have to be removed for washdown cycles.

• Switching distance: 30...200 mm, adjustable by teach-in and over IO-Link
• Output: push-pull, light / dark operate, < 100 mA
• Communication: IO-Link V1.1, filter functions, qTeach lock
• Supply: 10...30 V DC, typical consumption 30 mA
• Housing: stainless steel 1.4404 (V4A), PMMA optics, 16.5 x 34.7 x 28.2 mm
• Environment: IP 68/69K and proTect+, Ecolab, -25...+60 °C
• Connection: M8 connector, 4 pin

The sensor suits checks on bottles, cans and packaging in food and beverage production, where machines are washed regularly with hot pressurised water, foam and disinfectants. The switching distance is set with qTeach or over IO-Link, so there are no adjusters on the housing for dirt to collect in.

OR18.RR-PW1P.71O is a Baumer M18 retro-reflective photo sensor with a polarisation filter and a 3.5 m operating range. The polarisation filter lets the sensor tell the reflector from shiny objects, so glossy packaging or metal parts do not hold the output switched. Sensitivity is set with a 270° potentiometer on the housing.

• Operating range: 3.5 m (nominal 4.5 m), red LED 660 nm
• Output: PNP, max. 100 mA, light/dark operate; response time < 1 ms
• Supply: 12...30 V DC, max. 40 mA
• Housing: M18 x 1 threaded, 67.2 mm long, ABS plastic, PMMA lens
• Environment: IP67; -25...+55 °C
• Connection: M12 4-pin connector

Used for object detection across conveyors and gates where a reflector can be mounted opposite the sensor. Pin 2 (white) is a control input. A green LED shows alignment and lens soiling, a yellow LED shows the output state.

OR18W.RR-PW1P.9VO is the washdown version of the Baumer OR18 M18 retro-reflective photo sensor: the same 3.5 m range and polarisation filter in a stainless steel 1.4404 (V4A) housing rated IP 67/69K instead of the plastic one.

• Housing: stainless steel 1.4404 (V4A), M18 x 1 thread, 67.2 mm long, PMMA lens
• Environment: IP 67/69K; -25...+55 °C
• Operating range: 3.5 m actual (nominal 4.5 m), pulsed red LED 660 nm, polarisation filter
• Output: PNP, < 100 mA, light/dark operate; response time < 1 ms
• Supply: 12...30 V DC, max. 40 mA
• Connection: M12 4-pin connector

Suited to food, beverage and packaging lines that are washed down at high pressure, where a plastic sensor body would not survive the cleaning cycle. Sensitivity is set with a 270° potentiometer and pin 2 (white) is a control input. A green LED shows alignment against the reflector and lens soiling, a yellow LED the output state.

LX3EQ is the emitter of the Banner LX series light curtain, with a 67 mm light screen for part sensing. Infrared LEDs are spaced at 9.5 mm and fire in sequence, so together with an LX receiver of the same length they form a crosshatched beam pattern that also detects thin and narrow objects. No synchronisation wire is needed between emitter and receiver.

• Distance between emitter and receiver: 0.3...2 m (Normal), 0.15...0.6 m (Reduced)
• Output: none, the unit is an emitter
• Supply: 10...30 V DC, less than 1 W
• Housing: aluminium profile, die-cast zinc endcaps, acrylic lens; overall length 113.4 mm
• Environment: IP65, -20...+70 °C
• Connection: 150 mm cable with an M12 5-pin male connector

The light curtain is used for part ejection verification and package detection on conveyors, where the object may cross the beam field at any point. The range is selected with the grey wire: 5...30 V DC gives Normal, 0...2 V DC gives Reduced range, and the emitter LED indicators show the selection. The green LED is on when power is applied and the emitter is good; the red LED is on in reduced range. The emitter must be paired with an LX receiver of the same length and range, and the device is not intended for personnel protection.

Meets CE and UKCA requirements; UL listing E71083, Class 2 power, UL Environmental Rating Type 1.

LX3RQ is the receiver of the Banner LX series light curtain, with a 67 mm light screen for part sensing. Photodiodes are spaced at 9.5 mm and recognise each emitter pulse separately, so the crosshatched beam pattern also detects thin objects such as a sheet of paper. In the standard range the smallest detectable object is 9.5 mm in diameter.

• Distance between emitter and receiver: 0.3...2 m (Normal), 0.15...0.6 m (Reduced)
• Output: bipolar, one PNP and one NPN output at the same time, 125 mA each, conducting while the beam is blocked
• Response time: 0.8 ms on, 6 ms off with a 5 ms pulse stretcher
• Supply: 10...30 V DC, less than 1 W
• Housing: aluminium profile, die-cast zinc endcaps, acrylic lens; overall length 113.4 mm
• Environment: IP65, -20...+70 °C
• Connection: 150 mm cable with an M12 5-pin male connector

The receiver is used for part ejection verification and package detection on conveyors, where the object may cross the beam field at any point. The range is selected with the grey wire: 5...30 V DC gives Normal, 0...2 V DC gives Reduced range. The amber LED shows a conducting output, the bicolour LED shows green in Normal and red in Reduced range, and a flashing red light indicates a receiver hardware fault. Resolution is best in the middle 80 % of the beam field, the receiver must be paired with an LX emitter of the same length and range, and the device is not intended for personnel protection.

Meets CE and UKCA requirements; UL listing E71083, Class 2 power, UL Environmental Rating Type 1.

IGYX 12N17B1/S14L is a Baumer inductive proximity sensor in an M12 barrel with a 4 mm nominal sensing distance and a NPN normally open (NO) output. The sensing face is flush mountable and the nickel-plated brass housing is 60 mm long.

• Sensing distance: 4 mm (Sn), assured 3.2 mm (Sa)
• Output: NPN, normally open (NO), 200 mA, with short-circuit and reverse-polarity protection
• Supply: 10...30 V DC, current consumption up to 15 mA with no load
• Housing: M12 thread, nickel-plated brass, PBT sensing face, 60 mm long, flush mountable
• Environment: IP 67, operating temperature -25...+75 °C
• Connection: M12 connector

The sensor is intended for presence and end-position monitoring of metal parts on conveyors, pneumatic cylinders and indexing mechanisms. Switching frequency is 1.5 kHz. Tightening torque on the M12 thread must not exceed 10 Nm, and the switching point drifts by up to ±10 % of Sr across the temperature range, which matters when the target sits close to the 4 mm limit.

Complies with the EMC requirements of EN 60947-5-2:2007.

IGYX 12P17B1/S14L is a Baumer inductive proximity sensor in an M12 barrel with a 4 mm nominal sensing distance and a PNP normally open (NO) output. The sensing face is flush mountable and the nickel-plated brass housing is 60 mm long.

• Sensing distance: 4 mm (Sn), assured 3.2 mm (Sa)
• Output: PNP, normally open (NO), <200 mA, with short-circuit and reverse-polarity protection
• Supply: 10...30 V DC, current consumption up to 15 mA with no load
• Housing: M12 thread, nickel-plated brass, PBT sensing face, 60 mm long, flush mountable
• Environment: IP 67, operating temperature -25...+75 °C
• Connection: M12 connector

The sensor is intended for presence and end-position monitoring of metal parts on conveyors, pneumatic cylinders and indexing mechanisms. Switching frequency is <1.5 kHz. Tightening torque on the M12 thread must not exceed 10 Nm, and the switching point drifts by up to ±10 % of Sr across the temperature range, which matters when the target sits close to the 4 mm limit.

Complies with the EMC requirements of EN 60947-5-2:2007.

O200.ER-PV1Z.72CV/H006 is the receiver half of a Baumer O200 miniature through-beam pair with a 6 m nominal range. It carries no sensitivity adjustment - the switching threshold is preset at the factory, so the pair is aligned and left alone.

• Range: actual 5 m, nominal 6 m; smallest detectable object 5 mm (0.5 mm with aperture)
• Output: PNP complementary, light/dark operate, < 50 mA
• Supply: 10...30 VDC, typ. 16 mA at 24 VDC
• Response time: < 0.5 ms
• Housing: rectangular 8 x 25.1 x 14.1 mm, ASA plastic, PMMA optics, M3 stainless steel threaded sleeves
• Environment: IP 67, -25...+50 °C
• Connection: 2 m PVC cable, 4-wire

The fixed threshold suits series machines where the same gap is checked on every unit and commissioning should not include a sensitivity setting that can drift or be turned. A flashing output indicator reports weak signal margin or a soiled lens, and reciprocal influence is suppressed so several pairs can work side by side.

O200.TR-ZZZX.72CV/H006 is the emitter half of a Baumer O200 miniature through-beam pair, with a pulsed red LED at 644 nm and a 6 m nominal range. A test input switches the transmitter diode off, so the receiver channel can be verified from the controller without anyone reaching into the machine.

• Range: actual 5 m, nominal 6 m
• Light source: pulsed red LED, 644 nm
• Alignment: optical axis deviation < 1.5°, green power-on indicator
• Supply: 10...30 VDC, typ. 16 mA at 24 VDC
• Housing: rectangular 8 x 25.1 x 14.1 mm, ASA plastic, PMMA optics, M3 stainless steel threaded sleeves
• Environment: IP 67, -25...+50 °C
• Connection: 2 m PVC cable, 4-wire

A visible red beam is aligned by eye, which is the practical difference from the laser emitters in the same series over long spans. The emitter is used with an O200 through-beam receiver, which carries the switching output - the emitter has none of its own.

IGYX 08P37B3/S35L is a Baumer inductive proximity sensor in an M8 barrel with a 2 mm nominal sensing distance and a PNP normally closed (NC) output. The sensing face is flush mountable and the stainless steel housing is 36 mm long.

• Sensing distance: 2 mm (Sn), assured 1.6 mm (Sa)
• Output: PNP, normally closed (NC), 200 mA, with short-circuit and reverse-polarity protection
• Supply: 10...30 V DC, current consumption up to 15 mA with no load
• Housing: M8 thread, stainless steel, PBT sensing face, 36 mm long, flush mountable
• Environment: IP 67, operating temperature -25...+75 °C
• Connection: M8 connector

The Ø 8 mm body and 36 mm length fit the sensor into grippers, indexing tables and other positions where an M12 barrel does not fit. A 3 kHz switching frequency is enough for presence monitoring of fast moving metal parts. Tightening torque on the M8 thread must not exceed 5 Nm, and the switching point drifts by up to ±10 % of Sr across the temperature range, which matters when the target sits close to the 2 mm limit.

Complies with the EMC requirements of EN 60947-5-2:2007.

FHDK 10P5101/S35A is a Baumer miniature photo sensor with background suppression. It compares where the reflected beam lands on its internal detector, so an object is detected regardless of its colour or surface reflectivity while everything beyond the set distance is ignored. A 35...45 mm focus zone with a 4 mm beam diameter allows small objects to be detected.

• Switching distance: 20...120 mm, adjustable by a 5-turn mechanical potentiometer
• Output: PNP, Light/Dark Operate, < 100 mA
• Supply: 10...30 V DC, typical consumption 20 mA
• Housing: rectangular, 10.4 x 27 x 14 mm, plastic (ASA), PMMA optics
• Environment: IP 67, -25...+65 °C
• Connection: M8 connector, 4-pin

The sensor suits presence and position control in packaging, assembly and sorting machines where the background sits close to the object and dark or glossy surfaces give a standard diffuse sensor a false reading. A flashing light indicator shows insufficient signal margin or a soiled lens, so alignment and maintenance need no instruments. Reciprocal influence is suppressed, so several sensors can be mounted side by side.