CTX-3.3.3.B22.0 is a Baumer CTX series relative pressure sensor with a 0...10 bar measuring range and a 4...20 mA two-wire output. Pressure is sensed by a ceramic membrane (96 % Al2O3). Long-term stability is ≤ 0.3 % FSR per year.

• Measuring range: 0...10 bar, relative pressure
• Output: 4...20 mA, 2-wire
• Accuracy: ±0.5 % FSR (BFSL); max. measuring error ±2.5 % FSR
• Supply: 11...30 V DC
• Housing: AISI 304 (1.4301); process connection G 1/2" B EN 837-1, AISI 316L; NBR gasket
• Environment: IP 65 (EN 60529); process temperature -40...+100 °C; ambient temperature -40...+85 °C
• Connection: DIN EN 175301-803 A (DIN 43650 A) connector, 4-pin

The sensor is intended for pressure measurement in compressed air, technical gas and hydraulic systems - compressor stations, pneumatic lines and pump units. The output rise time (10...90 %) is ≤ 5 ms, which follows rapid pressure changes such as valve switching.

Complies with EN 61000-6-2, EN 61000-6-3 and EN 61326-1. Vibration and shock resistance tested to EN 60068-2-6, EN 60068-2-27 and EN 61373 (category 1, class B).

CTX-3.3.3.B24.0 is a Baumer CTX series relative pressure sensor with a 0...16 bar measuring range and a 4...20 mA two-wire output. Pressure is sensed by a ceramic membrane (96 % Al2O3). Long-term stability is ≤ 0.3 % FSR per year.

• Measuring range: 0...16 bar, relative pressure
• Output: 4...20 mA, 2-wire
• Accuracy: ±0.5 % FSR (BFSL); max. measuring error ±2.5 % FSR
• Supply: 11...30 V DC
• Housing: AISI 304 (1.4301); process connection G 1/2" B EN 837-1, AISI 316L; NBR gasket
• Environment: IP 65 (EN 60529); process temperature -40...+100 °C; ambient temperature -40...+85 °C
• Connection: DIN EN 175301-803 A (DIN 43650 A) connector, 4-pin

The sensor is intended for pressure measurement in compressed air, technical gas and hydraulic systems - compressor stations, pneumatic lines and pump units. The output rise time (10...90 %) is ≤ 5 ms, which follows rapid pressure changes such as valve switching.

Complies with EN 61000-6-2, EN 61000-6-3 and EN 61326-1. Vibration and shock resistance tested to EN 60068-2-6, EN 60068-2-27 and EN 61373 (category 1, class B).

AFI5-A813.4002.0300 is a Baumer CombiLyz inductive conductivity sensor with separate electronics: the probe with its G 1 A connection sits in the pipe, and the housing with display is wall-mounted up to 10 m away. It passes conductivity and temperature on as two separate 4...20 mA signals, and both solid-state relays in the display can be set as limit contacts.

• Measuring range: 14 selectable ranges, 0...500 µS/cm to 0...1000 mS/cm; temperature -20...150 °C
• Output: 2 x 4...20 mA (conductivity, temperature), 2 solid-state relays
• Supply: 15...35 V DC
• Housing: FlexHousing Ø80 mm, AISI 304, wall mounting, G 1 A hygienic connection, PEEK Natura probe L=60 mm
• Environment: IP67 / IP69K; process -20...140 °C (up to 150 °C for less than 1 h), up to 25 bar
• Connection: 2 x M16x1.5 cable glands, plastic; 10 m PUR sensor cable

Used for concentration control of CIP solutions and for phase separation between product, water and cleaning solution in dairy, brewery and beverage lines. The minimum measurable conductivity is 50 µS/cm, so the sensor does not suit demineralised or purified water. The split design keeps the electronics away from hot or hard-to-reach pipe sections.

cULus listed (E491206); wetted parts in PEEK Natura comply with FDA 21 CFR 177.2415.

AFI4-5830.4002.0200 is a Baumer CombiLyz inductive conductivity sensor with display and bottom process connection. It passes conductivity and temperature on as two separate 4...20 mA signals, and both solid-state relays in the display can be set as limit contacts.

• Measuring range: 14 selectable ranges, 0...500 µS/cm to 0...1000 mS/cm; temperature -20...150 °C
• Output: 2 x 4...20 mA (conductivity, temperature), 2 solid-state relays
• Supply: 15...35 V DC
• Housing: FlexHousing Ø80 mm, AISI 304, G 1 A hygienic connection, PEEK Natura probe L=83 mm
• Environment: IP67 / IP69K; process -20...140 °C (up to 150 °C for less than 1 h), up to 25 bar
• Connection: 2 x M16x1.5 cable glands, stainless steel AISI 304

Used for concentration control of CIP solutions and for phase separation between product, water and cleaning solution in dairy, brewery and beverage lines. The minimum measurable conductivity is 50 µS/cm, so the sensor does not suit demineralised or purified water.

cULus listed (E491206); wetted parts in PEEK Natura comply with FDA 21 CFR 177.2415.

AFI4-6830.4006.1313 is a Baumer CombiLyz inductive conductivity sensor with display and rear process connection. It passes conductivity and temperature on as two separate 4...20 mA signals, and over IO-Link 1.1 the same readings and the sensor settings are also available digitally.

• Measuring range: 14 selectable ranges, 0...500 µS/cm to 0...1000 mS/cm; temperature -20...150 °C
• Output: 2 x 4...20 mA (conductivity, temperature), 2 solid-state relays, IO-Link 1.1
• Supply: 15...35 V DC (18...30 V DC with IO-Link)
• Housing: FlexHousing Ø80 mm, AISI 304, G 1 A hygienic connection, PEEK Natura probe L=60 mm
• Environment: IP67 / IP69K; process -20...140 °C (up to 150 °C for less than 1 h), up to 25 bar
• Connection: 2 x M16x1.5 cable glands, stainless steel AISI 304

Used for concentration control of CIP solutions and for phase separation between product, water and cleaning solution in dairy, brewery and beverage lines. The minimum measurable conductivity is 50 µS/cm, so the sensor does not suit demineralised or purified water.

cULus listed (E491206); wetted parts in PEEK Natura comply with FDA 21 CFR 177.2415. 3-A (74-07) and EHEDG EL Class I approved version, supplied with conductivity (5-point) and temperature (3-point) calibration certificates.

PBMH-24B22RA14451F21000 is a Baumer PBMH series hygienic relative pressure sensor with a 0...10 bar measuring range, a 4...20 mA two-wire output and an ISO 2852 (Tri-Clamp) process connection. The design is fully welded, resistant to CIP cleaning media and suitable for SIP sterilisation.

• Accuracy: max. measuring error ±0.25 % FSR, including zero-point and span error, non-linearity and hysteresis (EN 61298-2); long-term stability ≤ 0.1 % FSR per year
• Measuring range: 0...10 bar, relative pressure; temperature coefficient ≤ 0.03 % FSR/10 K (zero point and span), compensated range -40...+85 °C
• Output: 4...20 mA, 2-wire, response time ≤ 5 ms; zero point and span adjustable with FlexProgrammer 9701
• Supply: 8...30 V DC
• Protection: short-circuit protected
• Housing: AISI 316L (1.4404); process connection ISO 2852 (Tri-Clamp) DN 33.7/38, Ø 50.5 mm, AISI 316L (1.4435), electropolished, Ra 0.4 µm; membrane Ra ≤ 0.4 µm; EPDM gasket; standard oil filling
• Environment: IP65; ambient temperature -40...+85 °C; process temperature -40...+125 °C
• Connection: DIN EN 175301-803 A (DIN 43650 A) connector, 4-pin

Intended for pressure measurement in food, beverage and dairy process tanks and pipework with Tri-Clamp connections. This variant has no cooling neck, so a SIP cycle at medium temperatures up to 150 °C must not exceed 60 minutes.

Hygiene conformity 3-A (74-07); EPDM gaskets conform to 3-A Sanitary Standard 18-03 Class I. EMC to EN 61000-6-3. Shock to EN 60068-2-27 (50 g / 11 ms, 100 g / 6 ms), vibration to EN 60068-2-6 (1.5 mm p-p 10...58 Hz, 10 g 58 Hz...2 kHz).

PFM43-2211.A1421.0 is a Baumer electromagnetic insertion flow meter for pipes from DN 80 to DN 500. It is inserted into the pipe through a G 1 A threaded connection, so a large line does not need a full-bore flow meter. It passes flow velocity on as a pulse or frequency signal, and it is configured with Baumer BCP software.

• Measuring range: flow velocity 0.4...10 m/s, pipes DN 80...DN 500
• Accuracy: ±2 % at ≥ 0.5 m/s, repeatability ±0.5 %
• Output: 2 x pulse/frequency/alarm; analogue 0...20 mA or 4...20 mA output - optional
• Supply: 10...30 V DC, ≤ 1 W
• Housing: AISI 316, L=176 mm; G 1 A connection in AISI 304, Hastelloy C electrodes, PEEK and PTFE seals
• Environment: IP67; process -10...100 °C, up to 100 bar; ambient -10...60 °C
• Connection: M12-A, 5-pin, stainless steel

The medium must have a conductivity above 20 µS/cm, so the meter is not suitable for demineralised water or oils. After power-up it is operational within 30 s, but calibration needs a warm-up of up to 15 min.

PFM43-2211.A2421.0 is a Baumer electromagnetic insertion flow meter for pipes from DN 80 to DN 1000. It is inserted into the pipe through a G 1 A threaded connection, so a large line does not need a full-bore flow meter. It passes flow velocity on as a pulse or frequency signal, and it is configured with Baumer BCP software.

• Measuring range: flow velocity 0.4...10 m/s, pipes DN 80...DN 1000
• Accuracy: ±2 % at ≥ 0.5 m/s, repeatability ±0.5 %
• Output: 2 x pulse/frequency/alarm; analogue 0...20 mA or 4...20 mA output - optional
• Supply: 10...30 V DC, ≤ 1 W
• Housing: AISI 316, L=244 mm; G 1 A connection in AISI 304, Hastelloy C electrodes, PEEK and PTFE seals
• Environment: IP67; process -10...100 °C, up to 100 bar; ambient -10...60 °C
• Connection: M12-A, 5-pin, stainless steel

The medium must have a conductivity above 20 µS/cm, so the meter is not suitable for demineralised water or oils. After power-up it is operational within 30 s, but calibration needs a warm-up of up to 15 min.

PFM43-2211.A3421.0 is a Baumer electromagnetic insertion flow meter for pipes from DN 80 to DN 2000. It is inserted into the pipe through a G 1 A threaded connection, so a large line does not need a full-bore flow meter. It passes flow velocity on as a pulse or frequency signal, and it is configured with Baumer BCP software.

• Measuring range: flow velocity 0.4...10 m/s, pipes DN 80...DN 2000
• Accuracy: ±2 % at ≥ 0.5 m/s, repeatability ±0.5 %
• Output: 2 x pulse/frequency/alarm; analogue 0...20 mA or 4...20 mA output - optional
• Supply: 10...30 V DC, ≤ 1 W
• Housing: AISI 316, L=462 mm; G 1 A connection in AISI 304, Hastelloy C electrodes, PEEK and PTFE seals
• Environment: IP67; process -10...100 °C, up to 100 bar; ambient -10...60 °C
• Connection: M12-A, 5-pin, stainless steel

The medium must have a conductivity above 20 µS/cm, so the meter is not suitable for demineralised water or oils. After power-up it is operational within 30 s, but calibration needs a warm-up of up to 15 min.

Temperatūras sensors TE2-1.4.7020.0080.0 Art: 11180504 G 1/2 A hygienic (A03) L=80mm D=6mm

PBMN-24B22RA14471212000 is a Baumer PBMN series relative pressure sensor with a flush membrane, a 0...10 bar measuring range and a 4...20 mA two-wire output. The cooling neck allows permanent operation at process temperatures up to 200 °C.

• Accuracy: max. measuring error ±0.25 % FSR, including zero-point and span error, non-linearity and hysteresis (EN 61298-2); long-term stability ≤ 0.1 % FSR per year
• Measuring range: 0...10 bar, relative pressure; temperature coefficient ≤ 0.03 % FSR/10 K (zero point and span), compensated range -40...+85 °C
• Output: 4...20 mA, 2-wire, response time ≤ 5 ms; zero point and span adjustable with FlexProgrammer 9701
• Supply: 8...30 V DC
• Protection: short-circuit protected
• Housing: AISI 316L (1.4404); process connection G 1/2 A DIN EN ISO 1179-2 (3852-E) with cooling neck, AISI 316L (1.4404); membrane AISI 316L (1.4435), Ra ≤ 0.4 µm; NBR gasket; NSF H1 oil filling
• Environment: IP65; ambient temperature -40...+85 °C; process temperature -40...+200 °C
• Connection: DIN EN 175301-803 A (DIN 43650 A) connector, 4-pin

Suited to pressure measurement in high-temperature processes, including permanent SIP/CIP cycles up to 200 °C. The oil filling is NSF H1 listed (FDA approved), so it can be used on food production equipment.

EMC to EN 61000-6-3. Shock to EN 60068-2-27 (50 g / 11 ms, 100 g / 6 ms), vibration to EN 60068-2-6 (1.5 mm p-p 10...58 Hz, 10 g 58 Hz...2 kHz).

LBFS-2.03421.0 is a capacitive point level switch from the Baumer CleverLevel series with a G 1/2" A hygienic process connection and a stainless steel M12 connector without LED indicators. The metal connector suits high-pressure washdown and positions where polycarbonate parts are not accepted.

• Switching: point level detection, Single Point, Two Point and Window trigger modes, hysteresis < ±1 mm, repeatability < ±1 mm
• Output: two PNP outputs (SW1, SW2), each separately High-Active or Low-Active, 50 mA, step response T90 0.1 s, adjustable damping 0...60 s
• Supply: 8.5...35 V DC, current consumption < 8 mA (typ.)
• Housing: stainless steel; wetted parts PEEK Natura and AISI 316L (1.4404), Ra ≤ 0.8 µm
• Environment: process temperature -40...115 °C (135 °C temporarily), process pressure -1...10 bar, IP67 and IP69K with a matching mating connector
• Connection: M12-A, 4-pin, stainless steel connector, without status LED indicators

The switch is intended for food, beverage and pharmaceutical plant, where the Ra ≤ 0.8 µm surface finish and the hygienic connection allow CIP cleaning. Without LED indicators the switching state can only be read in the control system, so setting it up requires access to the input signal. The hygienic connection limits process pressure to 10 bar.

Complies with EN 1935/2004, EN 10/2011 and EN 2023/2006, FDA, 3-A (74-07) and EHEDG EL Class I. The PEEK material complies with USP Class VI. cULus listed, E365692. Marine approvals: DNV, Lloyd's Register and CCS.

LBFS-01G21.0 is a capacitive point level switch from the Baumer CleverLevel series with a G 1/2" A ISO 228-1 process connection and a cooling neck that separates the electronics from the hot medium. Process temperature is therefore permitted up to 150 °C as long as ambient temperature stays below 50 °C.

• Switching: point level detection from the dielectric constant of the medium (DC > 1.5), hysteresis ±1 mm, repeatability ±1 mm
• Output: PNP, NO or NC selectable, 20 mA, response time 0.1 s, adjustable damping 0...10 s
• Supply: 12...30 V DC, current consumption 25 mA (typ.), 50 mA (max.)
• Housing: stainless steel; wetted parts PEEK Natura and AISI 316L (1.4404), Ra ≤ 0.8 µm
• Environment: process temperature -40...150 °C (continuous at ambient below 50 °C), process pressure -1...100 bar, IP67 and IP69K with appropriate cable
• Connection: M12-A, 4-pin, polycarbonate connector with a blue status LED indicator

The switch is intended for hot processes - steam and hot water systems, oil and fuel tanks, CIP solution tanks - where medium temperature exceeds the limits of the standard build. The switching point and the damping are set with Baumer FlexProgram software. Mounting position is free - top, bottom or side.

WHG approval for overfill and leakage control, CCS marine approval. The PEEK material complies with USP Class VI. EMC compliance to EN 61326 (installed in a closed metal tank).

PBSN-1.3.B16.A.A1.44.03.2.1.S01 is a Baumer PBSN series absolute pressure sensor with a 0...1.6 bar measuring range and a 4...20 mA two-wire output. Pressure is sensed by a ceramic measuring cell (96 % Al2O3) that is resistant to abrasive media.

• Accuracy: max. measuring error ±0.5 % FSR, including zero-point and span error, non-linearity and hysteresis (EN 61298-2); long-term stability ≤ 0.2 % FSR per year
• Measuring range: 0...1.6 bar, absolute pressure; temperature coefficient ≤ 0.08 % FSR/10 K (zero point and span), compensated range -20...+60 °C
• Output: 4...20 mA, 2-wire, rise time (10...90 %) ≤ 5 ms
• Supply: 8...30 V DC
• Protection: short-circuit protected
• Housing: AISI 304 (1.4301); process connection G 1/2 B EN 837-1, AISI 316L (1.4404); NBR gasket
• Environment: IP65; ambient temperature -20...+85 °C; process temperature -30...+100 °C
• Connection: DIN EN 175301-803 A (DIN 43650 A) connector, 4-pin

Absolute pressure is measured against vacuum, so the reading does not follow changes in atmospheric pressure. The NBR gasket sets the lower process temperature limit at -30 °C.

EMC to EN 61000-6-2, EN 61000-6-3 and EN 61326-1. Shock and vibration resistance to EN 61373 (category 1, class B).

LBFS-2.01111.0 is a capacitive point level switch from the Baumer CleverLevel series with a G 1/2" A ISO 228-1 BSC process thread. The Frequency Sweep measuring principle sets the switching point from the dielectric constant of the medium (DC > 1.5), and the device carries two independent outputs, SW1 and SW2, each set separately to High-Active or Low-Active logic.

• Switching: point level detection, Single Point, Two Point and Window trigger modes, hysteresis < ±1 mm, repeatability < ±1 mm
• Output: two PNP outputs (SW1, SW2), each separately High-Active or Low-Active, 50 mA, step response T90 0.1 s, adjustable damping 0...60 s
• Supply: 8.5...35 V DC, current consumption < 8 mA (typ.)
• Housing: stainless steel; wetted parts PEEK Natura and AISI 304 (1.4301), Ra ≤ 0.8 µm
• Environment: process temperature -40...115 °C (135 °C temporarily), process pressure -1...100 bar (-1...80 bar temporarily), IP67 and IP69K with a matching mating connector
• Connection: M12-A, 4-pin, polycarbonate connector with status LED indicators

The switch is intended for tanks and pipework in industrial plant with a G 1/2" internal thread and pressures up to 100 bar. Mounting position is free - top, bottom or side. Damping of up to 60 s is set so that surface movement or splashing does not cause false switching.

The PEEK material complies with USP Class VI. cULus listed, E365692. Marine approvals: DNV, Lloyd's Register and CCS. EMC compliance to EN 61326-1 and EN 50121-3-2.

LBFS-2.01421.0 is a capacitive point level switch from the Baumer CleverLevel series with a G 1/2" A hygienic process connection. The Frequency Sweep measuring principle sets the switching point from the dielectric constant of the medium (DC > 1.5), and the device carries two independent outputs, SW1 and SW2, each set separately to High-Active or Low-Active logic.

• Switching: point level detection, Single Point, Two Point and Window trigger modes, hysteresis < ±1 mm, repeatability < ±1 mm
• Output: two PNP outputs (SW1, SW2), each separately High-Active or Low-Active, 50 mA, step response T90 0.1 s, adjustable damping 0...60 s
• Supply: 8.5...35 V DC, current consumption < 8 mA (typ.)
• Housing: stainless steel; wetted parts PEEK Natura and AISI 316L (1.4404), Ra ≤ 0.8 µm
• Environment: process temperature -40...115 °C (135 °C temporarily), process pressure -1...10 bar, IP67 and IP69K with a matching mating connector
• Connection: M12-A, 4-pin, polycarbonate connector with status LED indicators

The switch is intended for tanks and pipework in food, beverage and pharmaceutical plant, where the Ra ≤ 0.8 µm surface finish and the hygienic connection allow CIP cleaning without removing the sensor. The hygienic connection limits process pressure to 10 bar. Mounting position is free - top, bottom or side.

Complies with EN 1935/2004, EN 10/2011 and EN 2023/2006, FDA, 3-A (74-07) and EHEDG EL Class I. The PEEK material complies with USP Class VI. cULus listed, E365692. Marine approvals: DNV, Lloyd's Register and CCS.

LBFS-2.01511.0 is a capacitive point level switch from the Baumer CleverLevel series with a G 1/2" A ISO 228-1 process connection for reverse assembly - the thread sits inside the body, so the sensor screws onto a nozzle projecting from the tank. Gasket ZPX3-14B0 (glass and aramide fibre with NBR) is included.

• Switching: point level detection from the dielectric constant of the medium (DC > 1.5), Single Point, Two Point and Window trigger modes, hysteresis < ±1 mm
• Output: two PNP outputs (SW1, SW2), each separately High-Active or Low-Active, 50 mA, step response T90 0.1 s, adjustable damping 0...60 s
• Supply: 8.5...35 V DC, current consumption < 8 mA (typ.)
• Housing: stainless steel; wetted parts PEEK Natura and AISI 304 (1.4301), Ra ≤ 0.8 µm
• Environment: process temperature -40...85 °C, process pressure -1...100 bar, IP67 and IP69K with a matching mating connector
• Connection: M12-A, 4-pin, polycarbonate connector with status LED indicators

The reverse-assembly build covers the case where the tank wall carries no internal thread and only a male-threaded nozzle is available. On this build the process temperature is limited to 85 °C and no temporary excursion above it is permitted. Mounting position is free - top, bottom or side.

The PEEK material complies with USP Class VI. cULus listed, E365692. Marine approvals: DNV, Lloyd's Register and CCS. EMC compliance to EN 61326-1 and EN 50121-3-2.

LBFS-2.01422.0 is a capacitive point level switch from the Baumer CleverLevel series with a G 1/2" A hygienic process connection and NPN outputs. The Frequency Sweep measuring principle sets the switching point from the dielectric constant of the medium (DC > 1.5), and the device carries two independent outputs, SW1 and SW2, each set separately to High-Active or Low-Active logic.

• Switching: point level detection, Single Point, Two Point and Window trigger modes, hysteresis < ±1 mm, repeatability < ±1 mm
• Output: two NPN outputs (SW1, SW2), each separately High-Active or Low-Active, 50 mA, step response T90 0.1 s, adjustable damping 0...60 s
• Supply: 8.5...35 V DC, current consumption < 8 mA (typ.)
• Housing: stainless steel; wetted parts PEEK Natura and AISI 316L (1.4404), Ra ≤ 0.8 µm
• Environment: process temperature -40...115 °C (135 °C temporarily), process pressure -1...10 bar, IP67 and IP69K with a matching mating connector
• Connection: M12-A, 4-pin, polycarbonate connector with status LED indicators

The NPN version is for control systems with a common positive potential, where inputs are switched to 0 V. In all other respects the switch matches the hygienic build for food, beverage and pharmaceutical plant: the Ra ≤ 0.8 µm surface finish allows CIP cleaning, and the hygienic connection limits process pressure to 10 bar.

Complies with EN 1935/2004, EN 10/2011 and EN 2023/2006, FDA, 3-A (74-07) and EHEDG EL Class I. The PEEK material complies with USP Class VI. cULus listed, E365692. Marine approvals: DNV, Lloyd's Register and CCS.

LBFS-2.01K21.0 is a capacitive point level switch from the Baumer CleverLevel series with a G 1/2" A hygienic process connection and an 82 mm probe. The extended probe places the switching point further from the tank wall, and this build is rated to 100 bar process pressure rather than the 10 bar of the standard hygienic connection.

• Immersion length: 82 mm
• Switching: point level detection, Single Point, Two Point and Window trigger modes, hysteresis < ±1 mm, repeatability < ±1 mm
• Output: two PNP outputs (SW1, SW2), each separately High-Active or Low-Active, 50 mA, step response T90 0.1 s, adjustable damping 0...60 s
• Supply: 8.5...35 V DC, current consumption < 8 mA (typ.)
• Housing: stainless steel; wetted parts PEEK Natura and AISI 316L (1.4404), Ra ≤ 0.8 µm
• Environment: process temperature -40...115 °C (135 °C temporarily), process pressure -1...100 bar (-1...80 bar temporarily), IP67 and IP69K with a matching mating connector
• Connection: M12-A, 4-pin, polycarbonate connector with status LED indicators

The extended build is intended for tanks with a thick wall or insulation, and for plant where the probe has to reach through a nozzle to the medium itself. The Ra ≤ 0.8 µm surface finish allows CIP cleaning. Mounting position is free - top, bottom or side.

Complies with EN 1935/2004, EN 10/2011 and EN 2023/2006, and FDA. The PEEK material complies with USP Class VI. cULus listed, E365692. Marine approvals: DNV, Lloyd's Register and CCS.

AFI4-5D30.4006.1300 is a Baumer CombiLyz inductive conductivity sensor with display and bottom process connection. It passes conductivity and temperature on as two separate 4...20 mA signals, and over IO-Link 1.1 the same readings and the sensor settings are also available digitally.

• Measuring range: 14 selectable ranges, 0...500 µS/cm to 0...1000 mS/cm; temperature -20...150 °C
• Output: 2 x 4...20 mA (conductivity, temperature), 2 solid-state relays, IO-Link 1.1
• Supply: 15...35 V DC (18...30 V DC with IO-Link)
• Housing: FlexHousing Ø80 mm, AISI 304, G 1 A hygienic connection, PEEK Natura probe L=60 mm
• Environment: IP67 / IP69K; process -20...140 °C (up to 150 °C for less than 1 h), up to 25 bar
• Connection: 1 x M12-A, 5-pin + 1 x M12-A, 8-pin, stainless steel AISI 304

Used for concentration control of CIP solutions and for phase separation between product, water and cleaning solution in dairy, brewery and beverage lines. The minimum measurable conductivity is 50 µS/cm, so the sensor does not suit demineralised or purified water.

cULus listed (E491206); wetted parts in PEEK Natura comply with FDA 21 CFR 177.2415.