SI-RF-A is the standard coded RFID actuator for Banner SI-RF safety switches. Its safety code is fixed and cannot be changed; the switch stores it during teach-in.

• Fits: SI-RF series safety switches
• Sensing distance with SI-RF: Sao 10 mm, Sar 25 mm, Sn 13 mm, hysteresis 2 mm
• Housing: thermoplastic, 36 x 26 x 15 mm
• Environment: IP69, -25...+70 °C

SGSA-MBK-10-4 is a set of four Banner clamp brackets for mounting SGS Safety Grid System emitters and receivers. Each bracket has a Ø 43 mm ring clamp closed with an M5 stud and a base with slotted holes.

• Fits: SGS Safety Grid System
• Clamp: Ø 43 mm ring, FH-M5x18 stud
• Dimensions: base 56 x 41 mm, height 89 mm, clamp centre 53 mm above the base
• Mounting: 6.8 mm slotted holes, 36 mm spacing
• Included: 4 brackets

EZLSA-MBK-16 is a Banner side-mount bracket for EZ-SCREEN LS safety light curtains, in black zinc die-cast, supplied as one bracket with hardware. The clamp turns 35° in total (+15°/-20°) for aligning the emitter and receiver.

• Fits: EZ-SCREEN LS safety light curtains
• Material: black zinc die-cast
• Dimensions: 74 x 55 mm, height 55 mm; 6.5 mm mounting holes, 58 mm spacing
• Tightening torque: M4 screws, max. 1.7 Nm and 2.3 Nm
• Included: 1 bracket with hardware

S4BA-MBK-11 is an end mount bracket kit for Banner EZ-SCREEN S4B safety light curtains: two L-brackets with a glass-filled polycarbonate adapter that lets the sensor rotate ±15°.

• Fits: S4B emitters and receivers with FID 3 or older
• Included: 2 brackets and mounting hardware
• Material: 8-gauge cold-rolled steel, black zinc finish; glass-filled polycarbonate adapter
• Adjustment: ±15° rotation

Not for FID 4 and later S4B units (the models with the lighted end cap). Light curtains longer than 900 mm also need a side mount bracket.

LPA-MBK-12 is a Banner side-mount bracket for EZ-SCREEN Low Profile emitters and receivers. The sensor can be rotated +10° / -30° in the bracket.

• Fits: Banner EZ-SCREEN Low Profile
• Type: side mount, right-angle
• Rotation: +10° / -30°
• Included: 1 bracket with hardware

S4BA-ML-LPQ20 is an L-configuration mute arm kit for Banner EZ-SCREEN S4B safety light curtains: one sensor arm with two Q20-2 retroreflective sensors and one reflector arm with two reflectors, all pre-installed. Together with an S4B pair and a Banner safety controller it forms a muting system.

• Included: 1 sensor arm with 2 S4BA-Q20-2VPLP-Q5 sensors, 1 reflector arm with 2 reflectors, mounting hardware for sensors and reflectors
• Sensors: retroreflective, visible red LED, up to 5 m, PNP, 10-30 V DC, light/dark operate
• Connection: 600 mm cable with 4-pin M12 connector per sensor
• Arms: 4 mm aluminium, black anodised; 50 x 50 x 400 mm
• Environment: IP67, -25...+70 °C

The arm mounts to an S4BA-MBK-16 bracket or directly to a flat surface; the M4 hardware for this is not included. Single-sided, left or right.

S4BA-MBK-16 is a side mount bracket kit for Banner EZ-SCREEN S4B safety light curtains, with ±15° rotation. Because the S4B beams run to both ends of the housing, units mounted on these brackets leave minimal or no gaps in detection.

• Fits: all S4B emitters and receivers
• Included: 2 brackets
• Material: glass-filled polycarbonate
• Mounting: 4 holes Ø4.5 mm, 25 mm hole spacing
• Adjustment: ±15° rotation

FID 4 S4B units passed the IEC 61496-1 (Class 3M4) vibration and shock tests mounted on S4BA-MBK-16 brackets.