OR18.RR-PW1P.71O is a Baumer M18 retro-reflective photo sensor with a polarisation filter and a 3.5 m operating range. The polarisation filter lets the sensor tell the reflector from shiny objects, so glossy packaging or metal parts do not hold the output switched. Sensitivity is set with a 270° potentiometer on the housing.

• Operating range: 3.5 m (nominal 4.5 m), red LED 660 nm
• Output: PNP, max. 100 mA, light/dark operate; response time < 1 ms
• Supply: 12...30 V DC, max. 40 mA
• Housing: M18 x 1 threaded, 67.2 mm long, ABS plastic, PMMA lens
• Environment: IP67; -25...+55 °C
• Connection: M12 4-pin connector

Used for object detection across conveyors and gates where a reflector can be mounted opposite the sensor. Pin 2 (white) is a control input. A green LED shows alignment and lens soiling, a yellow LED shows the output state.

OR18W.RR-PW1P.9VO is the washdown version of the Baumer OR18 M18 retro-reflective photo sensor: the same 3.5 m range and polarisation filter in a stainless steel 1.4404 (V4A) housing rated IP 67/69K instead of the plastic one.

• Housing: stainless steel 1.4404 (V4A), M18 x 1 thread, 67.2 mm long, PMMA lens
• Environment: IP 67/69K; -25...+55 °C
• Operating range: 3.5 m actual (nominal 4.5 m), pulsed red LED 660 nm, polarisation filter
• Output: PNP, < 100 mA, light/dark operate; response time < 1 ms
• Supply: 12...30 V DC, max. 40 mA
• Connection: M12 4-pin connector

Suited to food, beverage and packaging lines that are washed down at high pressure, where a plastic sensor body would not survive the cleaning cycle. Sensitivity is set with a 270° potentiometer and pin 2 (white) is a control input. A green LED shows alignment against the reflector and lens soiling, a yellow LED the output state.

IGYX 12N17B1/S14L is a Baumer inductive proximity sensor in an M12 barrel with a 4 mm nominal sensing distance and a NPN normally open (NO) output. The sensing face is flush mountable and the nickel-plated brass housing is 60 mm long.

• Sensing distance: 4 mm (Sn), assured 3.2 mm (Sa)
• Output: NPN, normally open (NO), 200 mA, with short-circuit and reverse-polarity protection
• Supply: 10...30 V DC, current consumption up to 15 mA with no load
• Housing: M12 thread, nickel-plated brass, PBT sensing face, 60 mm long, flush mountable
• Environment: IP 67, operating temperature -25...+75 °C
• Connection: M12 connector

The sensor is intended for presence and end-position monitoring of metal parts on conveyors, pneumatic cylinders and indexing mechanisms. Switching frequency is 1.5 kHz. Tightening torque on the M12 thread must not exceed 10 Nm, and the switching point drifts by up to ±10 % of Sr across the temperature range, which matters when the target sits close to the 4 mm limit.

Complies with the EMC requirements of EN 60947-5-2:2007.

IGYX 12P17B1/S14L is a Baumer inductive proximity sensor in an M12 barrel with a 4 mm nominal sensing distance and a PNP normally open (NO) output. The sensing face is flush mountable and the nickel-plated brass housing is 60 mm long.

• Sensing distance: 4 mm (Sn), assured 3.2 mm (Sa)
• Output: PNP, normally open (NO), <200 mA, with short-circuit and reverse-polarity protection
• Supply: 10...30 V DC, current consumption up to 15 mA with no load
• Housing: M12 thread, nickel-plated brass, PBT sensing face, 60 mm long, flush mountable
• Environment: IP 67, operating temperature -25...+75 °C
• Connection: M12 connector

The sensor is intended for presence and end-position monitoring of metal parts on conveyors, pneumatic cylinders and indexing mechanisms. Switching frequency is <1.5 kHz. Tightening torque on the M12 thread must not exceed 10 Nm, and the switching point drifts by up to ±10 % of Sr across the temperature range, which matters when the target sits close to the 4 mm limit.

Complies with the EMC requirements of EN 60947-5-2:2007.

O200.ER-PV1Z.72CV/H006 is the receiver half of a Baumer O200 miniature through-beam pair with a 6 m nominal range. It carries no sensitivity adjustment - the switching threshold is preset at the factory, so the pair is aligned and left alone.

• Range: actual 5 m, nominal 6 m; smallest detectable object 5 mm (0.5 mm with aperture)
• Output: PNP complementary, light/dark operate, < 50 mA
• Supply: 10...30 VDC, typ. 16 mA at 24 VDC
• Response time: < 0.5 ms
• Housing: rectangular 8 x 25.1 x 14.1 mm, ASA plastic, PMMA optics, M3 stainless steel threaded sleeves
• Environment: IP 67, -25...+50 °C
• Connection: 2 m PVC cable, 4-wire

The fixed threshold suits series machines where the same gap is checked on every unit and commissioning should not include a sensitivity setting that can drift or be turned. A flashing output indicator reports weak signal margin or a soiled lens, and reciprocal influence is suppressed so several pairs can work side by side.

O200.TR-ZZZX.72CV/H006 is the emitter half of a Baumer O200 miniature through-beam pair, with a pulsed red LED at 644 nm and a 6 m nominal range. A test input switches the transmitter diode off, so the receiver channel can be verified from the controller without anyone reaching into the machine.

• Range: actual 5 m, nominal 6 m
• Light source: pulsed red LED, 644 nm
• Alignment: optical axis deviation < 1.5°, green power-on indicator
• Supply: 10...30 VDC, typ. 16 mA at 24 VDC
• Housing: rectangular 8 x 25.1 x 14.1 mm, ASA plastic, PMMA optics, M3 stainless steel threaded sleeves
• Environment: IP 67, -25...+50 °C
• Connection: 2 m PVC cable, 4-wire

A visible red beam is aligned by eye, which is the practical difference from the laser emitters in the same series over long spans. The emitter is used with an O200 through-beam receiver, which carries the switching output - the emitter has none of its own.

PBMH-24B22RA14451F21000 is a Baumer PBMH series hygienic relative pressure sensor with a 0...10 bar measuring range, a 4...20 mA two-wire output and an ISO 2852 (Tri-Clamp) process connection. The design is fully welded, resistant to CIP cleaning media and suitable for SIP sterilisation.

• Accuracy: max. measuring error ±0.25 % FSR, including zero-point and span error, non-linearity and hysteresis (EN 61298-2); long-term stability ≤ 0.1 % FSR per year
• Measuring range: 0...10 bar, relative pressure; temperature coefficient ≤ 0.03 % FSR/10 K (zero point and span), compensated range -40...+85 °C
• Output: 4...20 mA, 2-wire, response time ≤ 5 ms; zero point and span adjustable with FlexProgrammer 9701
• Supply: 8...30 V DC
• Protection: short-circuit protected
• Housing: AISI 316L (1.4404); process connection ISO 2852 (Tri-Clamp) DN 33.7/38, Ø 50.5 mm, AISI 316L (1.4435), electropolished, Ra 0.4 µm; membrane Ra ≤ 0.4 µm; EPDM gasket; standard oil filling
• Environment: IP65; ambient temperature -40...+85 °C; process temperature -40...+125 °C
• Connection: DIN EN 175301-803 A (DIN 43650 A) connector, 4-pin

Intended for pressure measurement in food, beverage and dairy process tanks and pipework with Tri-Clamp connections. This variant has no cooling neck, so a SIP cycle at medium temperatures up to 150 °C must not exceed 60 minutes.

Hygiene conformity 3-A (74-07); EPDM gaskets conform to 3-A Sanitary Standard 18-03 Class I. EMC to EN 61000-6-3. Shock to EN 60068-2-27 (50 g / 11 ms, 100 g / 6 ms), vibration to EN 60068-2-6 (1.5 mm p-p 10...58 Hz, 10 g 58 Hz...2 kHz).

IGYX 08P37B3/S35L is a Baumer inductive proximity sensor in an M8 barrel with a 2 mm nominal sensing distance and a PNP normally closed (NC) output. The sensing face is flush mountable and the stainless steel housing is 36 mm long.

• Sensing distance: 2 mm (Sn), assured 1.6 mm (Sa)
• Output: PNP, normally closed (NC), 200 mA, with short-circuit and reverse-polarity protection
• Supply: 10...30 V DC, current consumption up to 15 mA with no load
• Housing: M8 thread, stainless steel, PBT sensing face, 36 mm long, flush mountable
• Environment: IP 67, operating temperature -25...+75 °C
• Connection: M8 connector

The Ø 8 mm body and 36 mm length fit the sensor into grippers, indexing tables and other positions where an M12 barrel does not fit. A 3 kHz switching frequency is enough for presence monitoring of fast moving metal parts. Tightening torque on the M8 thread must not exceed 5 Nm, and the switching point drifts by up to ±10 % of Sr across the temperature range, which matters when the target sits close to the 2 mm limit.

Complies with the EMC requirements of EN 60947-5-2:2007.

FHDK 10P5101/S35A is a Baumer miniature photo sensor with background suppression. It compares where the reflected beam lands on its internal detector, so an object is detected regardless of its colour or surface reflectivity while everything beyond the set distance is ignored. A 35...45 mm focus zone with a 4 mm beam diameter allows small objects to be detected.

• Switching distance: 20...120 mm, adjustable by a 5-turn mechanical potentiometer
• Output: PNP, Light/Dark Operate, < 100 mA
• Supply: 10...30 V DC, typical consumption 20 mA
• Housing: rectangular, 10.4 x 27 x 14 mm, plastic (ASA), PMMA optics
• Environment: IP 67, -25...+65 °C
• Connection: M8 connector, 4-pin

The sensor suits presence and position control in packaging, assembly and sorting machines where the background sits close to the object and dark or glossy surfaces give a standard diffuse sensor a false reading. A flashing light indicator shows insufficient signal margin or a soiled lens, so alignment and maintenance need no instruments. Reciprocal influence is suppressed, so several sensors can be mounted side by side.

EIL580P-SC10.7BF.01024.B is a Baumer optoPulse programmable incremental encoder with optical sensing. Pulse count from 1 to 65536, TTL or HTL output level, zero pulse width and position and signal sequence are set on site, so one encoder replaces several fixed-resolution models.

• Resolution: 1...65536 pulses per revolution, factory setting 1024
• Output: TTL/RS422 (factory setting) or HTL/push-pull, 6 channels, up to 300 kHz (TTL)
• Supply: 4.75-30 V DC, no-load consumption ≤70 mA
• Housing: Ø58 mm, clamping flange, Ø10 x 20 mm shaft with flat
• Environment: IP67 (with shaft seal), -40...+100 °C, up to 6000 rpm
• Connection: M12 8-pin radial connector

Parameters are set with the Baumer Z-PA-EI-H or Z-PA-EI-P programming tool and an M12/D-SUB connection cable. Unprogrammed, the encoder runs at 1024 pulses with a 5 V TTL output.

UL 508 / CSA 22.2 approved. EMC to EN 61000-6-2 and EN 61000-6-3; vibration (30 g, 10-2000 Hz) and shock (300 g, 6 ms) resistance to EN 60068-2-6 and EN 60068-2-27.

ESG 34FH0500G is a Baumer shielded M12 female cordset, 8-pin, straight, with the cable shield connected to the coupling nut.

• Connector: M12 female, straight, 8-pin, shield on coupling nut
• Cable: PUR, Ø approx. 5.9 mm, shielded, halogen-free, 5 m, suitable for drag chains
• Wire colours, pins 1-8: WH, BN, GN, YE, GY, PK, BU, RD
• Temperature: -25...+80 °C moving, -40...+80 °C fixed

UL listed, file number E315836.

EIL580-S1B1.7FE.01024.A is a Baumer optoPulse incremental encoder with optical sensing, 1024 pulses per revolution and a EURO flange B10. The flange, with a Ø85 mm centring collar and six Ø6.6 mm holes on a Ø100 mm pitch circle, matches EURO B10 motor and gearbox mounting.

• Resolution: 1024 pulses per revolution, zero pulse
• Output: TTL/RS422, 6 channels (A+, B+, R+, A-, B-, R-), up to 300 kHz
• Supply: 5 V DC ±5 %, no-load consumption ≤70 mA
• Housing: EURO flange B10 (Ø115 mm), Ø11 x 30 mm shaft with Woodruff key
• Environment: IP67 (with shaft seal), -40...+85 °C, up to 6000 rpm
• Connection: M23 12-pin radial connector

The encoder needs a regulated 5 V supply and cannot be connected directly to a 24 V circuit. The shaft needs a flexible coupling, as permitted load is 40 N axial and 80 N radial.

UL 508 / CSA 22.2 approved. EMC to EN 61000-6-2 and EN 61000-6-3; vibration (30 g, 10-2000 Hz) and shock (300 g, 6 ms) resistance to EN 60068-2-6 and EN 60068-2-27.

PFM43-2211.A1421.0 is a Baumer electromagnetic insertion flow meter for pipes from DN 80 to DN 500. It is inserted into the pipe through a G 1 A threaded connection, so a large line does not need a full-bore flow meter. It passes flow velocity on as a pulse or frequency signal, and it is configured with Baumer BCP software.

• Measuring range: flow velocity 0.4...10 m/s, pipes DN 80...DN 500
• Accuracy: ±2 % at ≥ 0.5 m/s, repeatability ±0.5 %
• Output: 2 x pulse/frequency/alarm; analogue 0...20 mA or 4...20 mA output - optional
• Supply: 10...30 V DC, ≤ 1 W
• Housing: AISI 316, L=176 mm; G 1 A connection in AISI 304, Hastelloy C electrodes, PEEK and PTFE seals
• Environment: IP67; process -10...100 °C, up to 100 bar; ambient -10...60 °C
• Connection: M12-A, 5-pin, stainless steel

The medium must have a conductivity above 20 µS/cm, so the meter is not suitable for demineralised water or oils. After power-up it is operational within 30 s, but calibration needs a warm-up of up to 15 min.

PFM43-2211.A2421.0 is a Baumer electromagnetic insertion flow meter for pipes from DN 80 to DN 1000. It is inserted into the pipe through a G 1 A threaded connection, so a large line does not need a full-bore flow meter. It passes flow velocity on as a pulse or frequency signal, and it is configured with Baumer BCP software.

• Measuring range: flow velocity 0.4...10 m/s, pipes DN 80...DN 1000
• Accuracy: ±2 % at ≥ 0.5 m/s, repeatability ±0.5 %
• Output: 2 x pulse/frequency/alarm; analogue 0...20 mA or 4...20 mA output - optional
• Supply: 10...30 V DC, ≤ 1 W
• Housing: AISI 316, L=244 mm; G 1 A connection in AISI 304, Hastelloy C electrodes, PEEK and PTFE seals
• Environment: IP67; process -10...100 °C, up to 100 bar; ambient -10...60 °C
• Connection: M12-A, 5-pin, stainless steel

The medium must have a conductivity above 20 µS/cm, so the meter is not suitable for demineralised water or oils. After power-up it is operational within 30 s, but calibration needs a warm-up of up to 15 min.

PFM43-2211.A3421.0 is a Baumer electromagnetic insertion flow meter for pipes from DN 80 to DN 2000. It is inserted into the pipe through a G 1 A threaded connection, so a large line does not need a full-bore flow meter. It passes flow velocity on as a pulse or frequency signal, and it is configured with Baumer BCP software.

• Measuring range: flow velocity 0.4...10 m/s, pipes DN 80...DN 2000
• Accuracy: ±2 % at ≥ 0.5 m/s, repeatability ±0.5 %
• Output: 2 x pulse/frequency/alarm; analogue 0...20 mA or 4...20 mA output - optional
• Supply: 10...30 V DC, ≤ 1 W
• Housing: AISI 316, L=462 mm; G 1 A connection in AISI 304, Hastelloy C electrodes, PEEK and PTFE seals
• Environment: IP67; process -10...100 °C, up to 100 bar; ambient -10...60 °C
• Connection: M12-A, 5-pin, stainless steel

The medium must have a conductivity above 20 µS/cm, so the meter is not suitable for demineralised water or oils. After power-up it is operational within 30 s, but calibration needs a warm-up of up to 15 min.

EIL580-SY06.5EQ.01000.A is a Baumer optoPulse incremental encoder with optical sensing, 1000 pulses per revolution and synchro flange mounting. The HTL output level follows the supply (Vout = Vin), so on a 24 V system the signal is at 24 V and goes straight to a PLC high-speed counter input.

• Resolution: 1000 pulses per revolution, zero pulse
• Output: HTL/push-pull, 6 channels (A+, B+, R+, A-, B-, R-), up to 160 kHz
• Supply: 4.75-30 V DC, no-load consumption ≤70 mA
• Housing: Ø58 mm, synchro flange with Ø50 mm centring collar, Ø6 x 10 mm shaft with flat
• Environment: IP65, -40...+85 °C, up to 12000 rpm

The synchro flange lets the encoder be held with clamps and rotated around its shaft before tightening. The shaft needs a flexible coupling.

UL 508 / CSA 22.2 approved. EMC to EN 61000-6-2 and EN 61000-6-3; vibration (30 g, 10-2000 Hz) and shock (300 g, 6 ms) resistance to EN 60068-2-6 and EN 60068-2-27.

Temperatūras sensors TE2-1.4.7020.0080.0 Art: 11180504 G 1/2 A hygienic (A03) L=80mm D=6mm

U500.DA5.2-UAMJ.72F is a Baumer U500 series ultrasonic distance sensor with a 20...1500 mm measuring range, a 0...10 V analog output and an IO-Link interface. It has two IO-Link channels (dual channel) and a multiplex version, so several sensors can run side by side without mutual interference.

• Accuracy: repeatability 0.5 mm; resolution < 0.3 mm; temperature drift < 2 % of object distance (> 50 mm); power-up drift compensated after 15 min
• Measuring range: 20...1500 mm, start and end point adjustable; response time < 70 ms; sonic frequency 200 kHz
• Outputs: analog 0...10 V / 10...0 V, up to 100 mA; IO-Link V1.1, COM 2 (38.4 kBaud), cycle time ≥ 12 ms, port type Class A, 48-bit process data (distance, 2 switching channels, quality, alarm, counter)
• Supply: 12...30 V DC, average consumption 35 mA; short-circuit and reverse-polarity protected
• Housing: rectangular, ASA/PMMA plastic, PEEK-coated sensor face, 18 x 45 x 32 mm
• Environment: IP67, operating temperature -25...+65 °C
• Connection: M12 connector, 5-pin

Suited to level measurement in tanks and distance measurement up to 1.5 m, where object colour, transparency or dust disturbs an optical measurement. The range is set by qTeach, Line-Teach or over IO-Link, which also configures filtering, the output characteristic, the sonic beam width and the function of pin 5.

FHDK 10P5101 is a Baumer miniature photo sensor with background suppression. It compares where the reflected beam lands on its internal detector, so an object is detected regardless of its colour or surface reflectivity while everything beyond the set distance is ignored. A 35...45 mm focus zone with a 4 mm beam diameter allows small objects to be detected.

• Switching distance: 20...120 mm, adjustable by a 5-turn mechanical potentiometer
• Output: PNP, Light/Dark Operate, < 100 mA
• Supply: 10...30 V DC, typical consumption 20 mA
• Housing: rectangular, 10.4 x 27 x 14 mm, plastic (ASA), PMMA optics
• Environment: IP 65, -25...+65 °C
• Connection: cable 2 m, 4-wire

The sensor suits presence and position control in packaging, assembly and sorting machines where the background sits close to the object and dark or glossy surfaces give a standard diffuse sensor a false reading. A flashing light indicator shows insufficient signal margin or a soiled lens, so alignment and maintenance need no instruments. Reciprocal influence is suppressed, so several sensors can be mounted side by side.

PBMN-24B22RA14471212000 is a Baumer PBMN series relative pressure sensor with a flush membrane, a 0...10 bar measuring range and a 4...20 mA two-wire output. The cooling neck allows permanent operation at process temperatures up to 200 °C.

• Accuracy: max. measuring error ±0.25 % FSR, including zero-point and span error, non-linearity and hysteresis (EN 61298-2); long-term stability ≤ 0.1 % FSR per year
• Measuring range: 0...10 bar, relative pressure; temperature coefficient ≤ 0.03 % FSR/10 K (zero point and span), compensated range -40...+85 °C
• Output: 4...20 mA, 2-wire, response time ≤ 5 ms; zero point and span adjustable with FlexProgrammer 9701
• Supply: 8...30 V DC
• Protection: short-circuit protected
• Housing: AISI 316L (1.4404); process connection G 1/2 A DIN EN ISO 1179-2 (3852-E) with cooling neck, AISI 316L (1.4404); membrane AISI 316L (1.4435), Ra ≤ 0.4 µm; NBR gasket; NSF H1 oil filling
• Environment: IP65; ambient temperature -40...+85 °C; process temperature -40...+200 °C
• Connection: DIN EN 175301-803 A (DIN 43650 A) connector, 4-pin

Suited to pressure measurement in high-temperature processes, including permanent SIP/CIP cycles up to 200 °C. The oil filling is NSF H1 listed (FDA approved), so it can be used on food production equipment.

EMC to EN 61000-6-3. Shock to EN 60068-2-27 (50 g / 11 ms, 100 g / 6 ms), vibration to EN 60068-2-6 (1.5 mm p-p 10...58 Hz, 10 g 58 Hz...2 kHz).

LBFS-2.03421.0 is a capacitive point level switch from the Baumer CleverLevel series with a G 1/2" A hygienic process connection and a stainless steel M12 connector without LED indicators. The metal connector suits high-pressure washdown and positions where polycarbonate parts are not accepted.

• Switching: point level detection, Single Point, Two Point and Window trigger modes, hysteresis < ±1 mm, repeatability < ±1 mm
• Output: two PNP outputs (SW1, SW2), each separately High-Active or Low-Active, 50 mA, step response T90 0.1 s, adjustable damping 0...60 s
• Supply: 8.5...35 V DC, current consumption < 8 mA (typ.)
• Housing: stainless steel; wetted parts PEEK Natura and AISI 316L (1.4404), Ra ≤ 0.8 µm
• Environment: process temperature -40...115 °C (135 °C temporarily), process pressure -1...10 bar, IP67 and IP69K with a matching mating connector
• Connection: M12-A, 4-pin, stainless steel connector, without status LED indicators

The switch is intended for food, beverage and pharmaceutical plant, where the Ra ≤ 0.8 µm surface finish and the hygienic connection allow CIP cleaning. Without LED indicators the switching state can only be read in the control system, so setting it up requires access to the input signal. The hygienic connection limits process pressure to 10 bar.

Complies with EN 1935/2004, EN 10/2011 and EN 2023/2006, FDA, 3-A (74-07) and EHEDG EL Class I. The PEEK material complies with USP Class VI. cULus listed, E365692. Marine approvals: DNV, Lloyd's Register and CCS.

LBFS-01G21.0 is a capacitive point level switch from the Baumer CleverLevel series with a G 1/2" A ISO 228-1 process connection and a cooling neck that separates the electronics from the hot medium. Process temperature is therefore permitted up to 150 °C as long as ambient temperature stays below 50 °C.

• Switching: point level detection from the dielectric constant of the medium (DC > 1.5), hysteresis ±1 mm, repeatability ±1 mm
• Output: PNP, NO or NC selectable, 20 mA, response time 0.1 s, adjustable damping 0...10 s
• Supply: 12...30 V DC, current consumption 25 mA (typ.), 50 mA (max.)
• Housing: stainless steel; wetted parts PEEK Natura and AISI 316L (1.4404), Ra ≤ 0.8 µm
• Environment: process temperature -40...150 °C (continuous at ambient below 50 °C), process pressure -1...100 bar, IP67 and IP69K with appropriate cable
• Connection: M12-A, 4-pin, polycarbonate connector with a blue status LED indicator

The switch is intended for hot processes - steam and hot water systems, oil and fuel tanks, CIP solution tanks - where medium temperature exceeds the limits of the standard build. The switching point and the damping are set with Baumer FlexProgram software. Mounting position is free - top, bottom or side.

WHG approval for overfill and leakage control, CCS marine approval. The PEEK material complies with USP Class VI. EMC compliance to EN 61326 (installed in a closed metal tank).

PBSN-1.3.B16.A.A1.44.03.2.1.S01 is a Baumer PBSN series absolute pressure sensor with a 0...1.6 bar measuring range and a 4...20 mA two-wire output. Pressure is sensed by a ceramic measuring cell (96 % Al2O3) that is resistant to abrasive media.

• Accuracy: max. measuring error ±0.5 % FSR, including zero-point and span error, non-linearity and hysteresis (EN 61298-2); long-term stability ≤ 0.2 % FSR per year
• Measuring range: 0...1.6 bar, absolute pressure; temperature coefficient ≤ 0.08 % FSR/10 K (zero point and span), compensated range -20...+60 °C
• Output: 4...20 mA, 2-wire, rise time (10...90 %) ≤ 5 ms
• Supply: 8...30 V DC
• Protection: short-circuit protected
• Housing: AISI 304 (1.4301); process connection G 1/2 B EN 837-1, AISI 316L (1.4404); NBR gasket
• Environment: IP65; ambient temperature -20...+85 °C; process temperature -30...+100 °C
• Connection: DIN EN 175301-803 A (DIN 43650 A) connector, 4-pin

Absolute pressure is measured against vacuum, so the reading does not follow changes in atmospheric pressure. The NBR gasket sets the lower process temperature limit at -30 °C.

EMC to EN 61000-6-2, EN 61000-6-3 and EN 61326-1. Shock and vibration resistance to EN 61373 (category 1, class B).

Sn = 18 mm, M30×1.5 metal thread (nickel-plated brass), flush, with 2 m cable connection, 6–36V DC, PNP NO/NC (changeover), GammaProx enhanced sensing distance, IP67

MHRM 12G5501 is a Baumer Hall-effect gearwheel sensor that detects the teeth of ferromagnetic gears from module 1 upwards. It has one push-pull output with a switching frequency of up to 15 kHz.

• Working distance: max. 0.7 mm at module 1, max. 2.4 mm at module 3
• Gear: ferromagnetic, module 1 or larger, width over 6 mm
• Output: push-pull, 30 mA, voltage drop below 5 VDC at 15 mA; switching frequency 0...15 kHz
• Supply: 8...28 VDC, max. 20 mA without load; short-circuit and reverse-polarity protected
• Housing: cylindrical threaded, Ø12 mm, 50 mm long, nickel-plated brass, PBTP sensing face
• Environment: IP67, -40...+85 °C
• Connection: 2 m PUR cable

Mounting is rotationally symmetric: the sensor's position about its own axis relative to the gear does not need aligning.

CE and UL approved.

OM60-PR0135.HH.YUFV is a Baumer OM60 laser distance sensor with a 70 mm measuring range at 65...135 mm and a spot beam. The distance is output as an analogue 0...10 V or 0...5 V signal, and at the same time the 32-bit measured value and the sensor settings are available over IO-Link 1.1.3.

• Measuring range: 65...135 mm (70 mm); repeatability 0.7 µm, linearity ±30 µm
• Output: 0...10 V / 0...5 V analogue, IO-Link V1.1.3 (Class A, COM3)
• Supply: 18...30 V DC, max. 100 mA
• Housing: 27.2 x 66 x 57 mm, PBT-ASA plastic, PMMA front; red laser 660 nm, laser class 1
• Environment: IP67; -10...+50 °C; ambient light up to 15 klx
• Connection: M12 5-pin connector on a 300 mm cable

A measuring frequency of 2000 Hz and a response time of 1 ms allow measurement on moving parts. Exposure time adjusts automatically, so the reading stays stable when the material colour or surface changes. The IO-Link process data follow the Smart Sensor Profile and carry, besides the measured value, two switching channels and quality and alarm bits.

Vibration resistance tested to IEC 60068-2-6, shock resistance to IEC 60068-2-27.

OM60-LR0060.HH.TXFV is a Baumer OM60 laser distance sensor with a 20 mm measuring range at 40...60 mm and a line-shaped beam. The line beam is intended for structured surfaces, where a spot beam would follow individual grooves or fibres. The measured value is read over RS485 with the Modbus RTU protocol.

• Measuring range: 40...60 mm (20 mm); repeatability 0.27 µm, linearity ±6 µm
• Output: RS485, Modbus RTU, 115200 Bd (adjustable)
• Supply: 18...30 V DC, max. 100 mA
• Housing: 27.2 x 66 x 57 mm, PBT-ASA plastic, PMMA front; red laser 660 nm, laser class 1
• Environment: IP67; -10...+50 °C; ambient light up to 15 klx
• Connection: M12 5-pin connector on a 300 mm cable

A measuring frequency of 3300 Hz and a response time of 0.65 ms allow measurement on moving parts. Exposure time adjusts automatically, so the reading stays stable when the material colour or surface changes. Settings are made on the display, over RS485 or through the external input.

Vibration resistance tested to IEC 60068-2-6, shock resistance to IEC 60068-2-27.

CAM12.A12-11230359 is a Baumer shielded M12 female cordset, 12-pin A-coded, with open-ended wires on the other end. The tinned-copper braid gives approx. 80 % coverage, and the wire ends carry a labelling sleeve.

• Connector: M12 female, straight, A-coded, 12-pin, FKM seal, nickel-plated zinc knurled nut
• Cable: PUR, black, Ø 6.5 mm, 12 × 0.14 mm² (AWG 26), shielded, 5 m, 80 mm stripped
• Rating: max. 1.5 A per contact, max. 30 V AC/DC
• Flexing: approx. 5 million C-track bending cycles, torsion ±30°/m
• Protection: IP65, IP66K, IP67
• Temperature: -25...+80 °C moving, -40...+80 °C fixed

Wire colours on pins 1-12: BN, BU, WH, GN, PK, YE, BK, GY, RD, VT, GYPK, RDBU. The cable is halogen-free, silicone-free and UV-resistant, flame-retardant to UL 1581 §1090 (H), CSA FT2 and IEC 60332-2-2.

OT200.DN-GLZZJ.72CV is a distance sensor from the Baumer OT200 series, measuring by time of flight over a 0...2000 mm range. It reports the measured distance over IO-Link and at the same time switches two freely set switching points.

• Measuring range: 0...2000 mm (Sd), repeat accuracy ≤ 1.25...1.5 mm
• Output: push-pull (PNP/NPN) and IO-Link V1.1.4, Class A
• Linearity error: ± 10 mm
• Supply: 10...30 V DC, consumption max. 55 mA
• Housing: plastic (ASA, PMMA), 8 x 25.1 x 15.8 mm, smooth stainless steel mounting sleeve
• Environment: IP 67, -25...+50 °C
• Connection: 2 m cable, 4 cores

The infrared laser diode (940 nm, laser class 1) also works in dusty and smoky environments, while a visible red Alignment Guide beam is used for alignment. Response time is selected over IO-Link: < 25 ms in High Speed, < 50 ms in Standard and < 200 ms in High Accuracy mode. Suppression of reciprocal influence allows several sensors to be mounted side by side.

Vibration and shock resistance tested to IEC 60068-2-6:2008 (10 g, 10...2000 Hz) and IEC 60068-2-27:2009 (50 g / 11 ms).

OT200.GN-GLZZJ.72CV is a background suppression photo sensor from the Baumer OT200 series, measuring by time of flight over a 0...2000 mm switching range. It measures distance directly instead of judging the amount of reflected light, so dark and shiny objects are detected at the same point. The measured distance value is additionally available over IO-Link.

• Switching range: 0...2000 mm (Tw), set by qTeach or IO-Link
• Output: push-pull (PNP/NPN) and IO-Link V1.1.4, Class A, Light operate, switchable
• Repeat accuracy: ≤ 1.25...1.5 mm
• Supply: 10...30 V DC, consumption typically 25 mA (24 V DC)
• Housing: plastic (ASA, PMMA), 8 x 25.1 x 15.8 mm, smooth stainless steel mounting sleeve
• Environment: IP 67, -25...+50 °C
• Connection: 2 m PVC cable, 4 x 0.08 mm²

The infrared laser diode (940 nm, laser class 1) also works in dusty and smoky environments, while a visible red Alignment Guide beam is used for alignment. qTeach setup needs no button, so the switching point cannot be changed by accident during production. Suppression of reciprocal influence allows several sensors to be mounted side by side.

Vibration and shock resistance tested to IEC 60068-2-6:2008 (10 g, 10...2000 Hz) and IEC 60068-2-27:2009 (50 g / 11 ms).

OT200.SN-GDZZJ.72CV is a SmartReflect light barrier from the Baumer OT200 series - it forms the beam between the sensor and a fixed background instead of a separate reflector. The background position Sde is set anywhere between 300 and 2000 mm, and an object is detected as soon as it enters the beam ahead of the background. The measured distance value is additionally available over IO-Link.

• Background position: 300...2000 mm (Sde), scanning range 90...94 % Sde
• Output: push-pull (PNP/NPN) and IO-Link V1.1.4, Class A, Light operate, switchable
• Output current: 100 mA
• Supply: 10...30 V DC, consumption typically 25 mA (24 V DC)
• Housing: plastic (ASA, PMMA), 8 x 25.1 x 15.8 mm, smooth stainless steel mounting sleeve
• Environment: IP 67, -25...+50 °C
• Connection: 2 m PVC cable, 4 x 0.08 mm²

The reflector-free barrier principle suits positions where a reflector has nowhere to mount or soils quickly - the conveyor belt, machine frame or wall serves as the background. The infrared laser diode (940 nm, laser class 1) also works in dusty and smoky environments, while a visible red Alignment Guide beam is used for alignment.

Vibration and shock resistance tested to IEC 60068-2-6:2008 (10 g, 10...2000 Hz) and IEC 60068-2-27:2009 (50 g / 11 ms).

OT330.GN-GLZZJ.72OV/0030 is a background suppression photo sensor from the Baumer OT330 series in a miniature housing, measuring by time of flight over a 0...2500 mm switching range. Distance is measured directly, so a black and a white object are detected at the same point (black/white shift 0 %). The measured distance value is available over IO-Link.

• Switching range: 0...2500 mm (Tw), set by qTeach or IO-Link
• Output: push-pull (PNP/NPN) and IO-Link V1.1.4, Class A, Light operate
• Output current: 100 mA, repeat accuracy < 2...1.5 mm
• Supply: 10...30 V DC, consumption typically 25 mA (24 V DC)
• Housing: plastic (ABS, ASA, PMMA), 11 x 32 x 21 mm, smooth brass mounting sleeve
• Environment: IP 67, -25...+55 °C
• Connection: M12 flylead connector, 300 mm

The infrared laser diode (940 nm, laser class 1) also works in dusty and smoky environments, while a visible red Alignment Guide beam is used for alignment. Response time is selected over IO-Link: < 25 ms in High Speed, < 50 ms in Standard and < 200 ms in High Accuracy mode. Suppression of reciprocal influence allows several sensors to be mounted side by side.

Vibration and shock resistance tested to IEC 60068-2-6:2008 (10 g, 10...2000 Hz) and IEC 60068-2-27:2009 (50 g / 11 ms resp. 100 g / 6 ms).

LBFS-2.01111.0 is a capacitive point level switch from the Baumer CleverLevel series with a G 1/2" A ISO 228-1 BSC process thread. The Frequency Sweep measuring principle sets the switching point from the dielectric constant of the medium (DC > 1.5), and the device carries two independent outputs, SW1 and SW2, each set separately to High-Active or Low-Active logic.

• Switching: point level detection, Single Point, Two Point and Window trigger modes, hysteresis < ±1 mm, repeatability < ±1 mm
• Output: two PNP outputs (SW1, SW2), each separately High-Active or Low-Active, 50 mA, step response T90 0.1 s, adjustable damping 0...60 s
• Supply: 8.5...35 V DC, current consumption < 8 mA (typ.)
• Housing: stainless steel; wetted parts PEEK Natura and AISI 304 (1.4301), Ra ≤ 0.8 µm
• Environment: process temperature -40...115 °C (135 °C temporarily), process pressure -1...100 bar (-1...80 bar temporarily), IP67 and IP69K with a matching mating connector
• Connection: M12-A, 4-pin, polycarbonate connector with status LED indicators

The switch is intended for tanks and pipework in industrial plant with a G 1/2" internal thread and pressures up to 100 bar. Mounting position is free - top, bottom or side. Damping of up to 60 s is set so that surface movement or splashing does not cause false switching.

The PEEK material complies with USP Class VI. cULus listed, E365692. Marine approvals: DNV, Lloyd's Register and CCS. EMC compliance to EN 61326-1 and EN 50121-3-2.

LBFS-2.01421.0 is a capacitive point level switch from the Baumer CleverLevel series with a G 1/2" A hygienic process connection. The Frequency Sweep measuring principle sets the switching point from the dielectric constant of the medium (DC > 1.5), and the device carries two independent outputs, SW1 and SW2, each set separately to High-Active or Low-Active logic.

• Switching: point level detection, Single Point, Two Point and Window trigger modes, hysteresis < ±1 mm, repeatability < ±1 mm
• Output: two PNP outputs (SW1, SW2), each separately High-Active or Low-Active, 50 mA, step response T90 0.1 s, adjustable damping 0...60 s
• Supply: 8.5...35 V DC, current consumption < 8 mA (typ.)
• Housing: stainless steel; wetted parts PEEK Natura and AISI 316L (1.4404), Ra ≤ 0.8 µm
• Environment: process temperature -40...115 °C (135 °C temporarily), process pressure -1...10 bar, IP67 and IP69K with a matching mating connector
• Connection: M12-A, 4-pin, polycarbonate connector with status LED indicators

The switch is intended for tanks and pipework in food, beverage and pharmaceutical plant, where the Ra ≤ 0.8 µm surface finish and the hygienic connection allow CIP cleaning without removing the sensor. The hygienic connection limits process pressure to 10 bar. Mounting position is free - top, bottom or side.

Complies with EN 1935/2004, EN 10/2011 and EN 2023/2006, FDA, 3-A (74-07) and EHEDG EL Class I. The PEEK material complies with USP Class VI. cULus listed, E365692. Marine approvals: DNV, Lloyd's Register and CCS.

LBFS-2.01511.0 is a capacitive point level switch from the Baumer CleverLevel series with a G 1/2" A ISO 228-1 process connection for reverse assembly - the thread sits inside the body, so the sensor screws onto a nozzle projecting from the tank. Gasket ZPX3-14B0 (glass and aramide fibre with NBR) is included.

• Switching: point level detection from the dielectric constant of the medium (DC > 1.5), Single Point, Two Point and Window trigger modes, hysteresis < ±1 mm
• Output: two PNP outputs (SW1, SW2), each separately High-Active or Low-Active, 50 mA, step response T90 0.1 s, adjustable damping 0...60 s
• Supply: 8.5...35 V DC, current consumption < 8 mA (typ.)
• Housing: stainless steel; wetted parts PEEK Natura and AISI 304 (1.4301), Ra ≤ 0.8 µm
• Environment: process temperature -40...85 °C, process pressure -1...100 bar, IP67 and IP69K with a matching mating connector
• Connection: M12-A, 4-pin, polycarbonate connector with status LED indicators

The reverse-assembly build covers the case where the tank wall carries no internal thread and only a male-threaded nozzle is available. On this build the process temperature is limited to 85 °C and no temporary excursion above it is permitted. Mounting position is free - top, bottom or side.

The PEEK material complies with USP Class VI. cULus listed, E365692. Marine approvals: DNV, Lloyd's Register and CCS. EMC compliance to EN 61326-1 and EN 50121-3-2.

LBFS-2.01422.0 is a capacitive point level switch from the Baumer CleverLevel series with a G 1/2" A hygienic process connection and NPN outputs. The Frequency Sweep measuring principle sets the switching point from the dielectric constant of the medium (DC > 1.5), and the device carries two independent outputs, SW1 and SW2, each set separately to High-Active or Low-Active logic.

• Switching: point level detection, Single Point, Two Point and Window trigger modes, hysteresis < ±1 mm, repeatability < ±1 mm
• Output: two NPN outputs (SW1, SW2), each separately High-Active or Low-Active, 50 mA, step response T90 0.1 s, adjustable damping 0...60 s
• Supply: 8.5...35 V DC, current consumption < 8 mA (typ.)
• Housing: stainless steel; wetted parts PEEK Natura and AISI 316L (1.4404), Ra ≤ 0.8 µm
• Environment: process temperature -40...115 °C (135 °C temporarily), process pressure -1...10 bar, IP67 and IP69K with a matching mating connector
• Connection: M12-A, 4-pin, polycarbonate connector with status LED indicators

The NPN version is for control systems with a common positive potential, where inputs are switched to 0 V. In all other respects the switch matches the hygienic build for food, beverage and pharmaceutical plant: the Ra ≤ 0.8 µm surface finish allows CIP cleaning, and the hygienic connection limits process pressure to 10 bar.

Complies with EN 1935/2004, EN 10/2011 and EN 2023/2006, FDA, 3-A (74-07) and EHEDG EL Class I. The PEEK material complies with USP Class VI. cULus listed, E365692. Marine approvals: DNV, Lloyd's Register and CCS.

LBFS-2.01K21.0 is a capacitive point level switch from the Baumer CleverLevel series with a G 1/2" A hygienic process connection and an 82 mm probe. The extended probe places the switching point further from the tank wall, and this build is rated to 100 bar process pressure rather than the 10 bar of the standard hygienic connection.

• Immersion length: 82 mm
• Switching: point level detection, Single Point, Two Point and Window trigger modes, hysteresis < ±1 mm, repeatability < ±1 mm
• Output: two PNP outputs (SW1, SW2), each separately High-Active or Low-Active, 50 mA, step response T90 0.1 s, adjustable damping 0...60 s
• Supply: 8.5...35 V DC, current consumption < 8 mA (typ.)
• Housing: stainless steel; wetted parts PEEK Natura and AISI 316L (1.4404), Ra ≤ 0.8 µm
• Environment: process temperature -40...115 °C (135 °C temporarily), process pressure -1...100 bar (-1...80 bar temporarily), IP67 and IP69K with a matching mating connector
• Connection: M12-A, 4-pin, polycarbonate connector with status LED indicators

The extended build is intended for tanks with a thick wall or insulation, and for plant where the probe has to reach through a nozzle to the medium itself. The Ra ≤ 0.8 µm surface finish allows CIP cleaning. Mounting position is free - top, bottom or side.

Complies with EN 1935/2004, EN 10/2011 and EN 2023/2006, and FDA. The PEEK material complies with USP Class VI. cULus listed, E365692. Marine approvals: DNV, Lloyd's Register and CCS.

EIL580-SC10.5FH.01024.A is a Baumer optoPulse incremental encoder with optical sensing and 1024 pulses per revolution. It runs on an 8-30 V DC supply while the output stays at 5 V TTL/RS422 level, so it connects to an RS422 input on a machine that only has 24 V available.

• Resolution: 1024 pulses per revolution, zero pulse
• Output: TTL/RS422, 6 channels (A+, B+, R+, A-, B-, R-), up to 300 kHz
• Supply: 8-30 V DC, no-load consumption ≤70 mA
• Housing: Ø58 mm, clamping flange with Ø36 mm centring collar, Ø10 x 20 mm shaft with flat
• Environment: IP65, -40...+85 °C, up to 12000 rpm
• Connection: M23 12-pin radial connector

Used for motor speed and position feedback where the controller or frequency converter has an RS422 input. Permitted shaft load is 40 N axial and 80 N radial, so the shaft needs a flexible coupling.

UL 508 / CSA 22.2 approved. EMC to EN 61000-6-2 and EN 61000-6-3; vibration (30 g, 10-2000 Hz) and shock (300 g, 6 ms) resistance to EN 60068-2-6 and EN 60068-2-27.

O200.EL-PV1T.72NV/FREC_H006 is the receiver half of a Baumer O200 miniature through-beam pair, working with a pulsed red laser emitter over a 6 m nominal range. Sensitivity is set with qTeach - a ferromagnetic tool held against the housing instead of a potentiometer - so once the machine runs there is no adjustment on the sensor for anyone to turn.

• Range: actual 5 m, nominal 6 m; smallest detectable object 3 mm (0.5 mm with aperture)
• Output: PNP complementary, light/dark operate, 50 mA
• Supply: 10...30 VDC, typ. 10 mA at 24 VDC
• Response time: < 0.1 ms, jitter < 0.03 ms
• Housing: rectangular 8 x 25.1 x 14.1 mm, ASA plastic, PMMA optics, M3 stainless steel threaded sleeves
• Environment: IP 67, -25...+50 °C
• Connection: M8 4-pin flylead connector, 200 mm

Typical positions are counting and presence checks on packaging and assembly lines, where the aperture accessory brings 0.5 mm parts and gaps within reach. A flashing output indicator reports weak signal margin or a soiled lens, so alignment is checked without instruments. Reciprocal influence is suppressed, so several pairs can work side by side.

O200.TL-GZZY.72NV/FIN2_H006 is the emitter half of a Baumer O200 miniature through-beam pair, with a parallel red laser beam rather than a diverging one, so detection stays even across the whole 6 m nominal range. The emitter diode is switched off either through the test input or over IO-Link, letting a controller verify the receiver channel without anyone breaking the beam by hand.

• Range: actual 5 m, nominal 6 m; parallel beam
• Light source: pulsed red laser diode, 680 nm, laser class 1
• Communication: IO-Link V1.1, port class A, 230.4 kBaud, cycle ≥ 0.6 ms
• Supply: 10...30 VDC, typ. 10 mA at 24 VDC
• Housing: rectangular 8 x 25.1 x 15.8 mm, ASA plastic, PMMA optics, M3 stainless steel threaded sleeves
• Environment: IP 67, -20...+50 °C
• Connection: M8 4-pin flylead connector, 200 mm

A parallel beam pays off where the pair sits at an awkward distance or the object passes close to one side: the spot does not grow with range, so the smallest detectable object and the alignment tolerance are the same at 0.5 m as at 5 m. The emitter is used with an O200 through-beam receiver, which carries the switching output - the emitter has none of its own.

EN380.IL-SMA6.5C1H1.00250.H is a Baumer EN380 series incremental encoder with optical sensing, a synchro flange and a solid shaft. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 250 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, synchro flange, stainless steel shaft ø6 x 12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder mounts on a motor or gearbox shaft end through a flexible coupling, and the synchro flange fits it into a tight installation without a separate mounting plate. Permissible speed is 8000 rpm.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-SMA5.5C1T1.01024.H is a Baumer EN380 series incremental encoder with optical sensing, a synchro flange and a solid shaft. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 1024 pulses per revolution
• Output: TTL/RS422, channels A, B and reference R with inverted signals, up to 300 kHz
• Supply: 5 VDC ±5 %, 60 mA without load
• Housing: aluminium, synchro flange, stainless steel shaft ø5 x 12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder mounts on a motor or gearbox shaft end through a flexible coupling, and the synchro flange fits it into a tight installation without a separate mounting plate. Permissible speed is 8000 rpm.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-SMA5.5C1T1.00500.H is a Baumer EN380 series incremental encoder with optical sensing, a synchro flange and a solid shaft. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 500 pulses per revolution
• Output: TTL/RS422, channels A, B and reference R with inverted signals, up to 300 kHz
• Supply: 5 VDC ±5 %, 60 mA without load
• Housing: aluminium, synchro flange, stainless steel shaft ø5 x 12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder mounts on a motor or gearbox shaft end through a flexible coupling, and the synchro flange fits it into a tight installation without a separate mounting plate. Permissible speed is 8000 rpm.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-SMA5.5C1T1.00360.H is a Baumer EN380 series incremental encoder with optical sensing, a synchro flange and a solid shaft. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 360 pulses per revolution
• Output: TTL/RS422, channels A, B and reference R with inverted signals, up to 300 kHz
• Supply: 5 VDC ±5 %, 60 mA without load
• Housing: aluminium, synchro flange, stainless steel shaft ø5 x 12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder mounts on a motor or gearbox shaft end through a flexible coupling, and the synchro flange fits it into a tight installation without a separate mounting plate. Permissible speed is 8000 rpm.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-SMA5.5C1H1.00500.H is a Baumer EN380 series incremental encoder with optical sensing, a synchro flange and a solid shaft. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 500 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, synchro flange, stainless steel shaft ø5 x 12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder mounts on a motor or gearbox shaft end through a flexible coupling, and the synchro flange fits it into a tight installation without a separate mounting plate. Permissible speed is 8000 rpm.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-SMA5.5C1H1.00360.H is a Baumer EN380 series incremental encoder with optical sensing, a synchro flange and a solid shaft. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 360 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, synchro flange, stainless steel shaft ø5 x 12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder mounts on a motor or gearbox shaft end through a flexible coupling, and the synchro flange fits it into a tight installation without a separate mounting plate. Permissible speed is 8000 rpm.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-SMA5.5C1H1.00100.H is a Baumer EN380 series incremental encoder with optical sensing, a synchro flange and a solid shaft. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 100 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, synchro flange, stainless steel shaft ø5 x 12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder mounts on a motor or gearbox shaft end through a flexible coupling, and the synchro flange fits it into a tight installation without a separate mounting plate. Permissible speed is 8000 rpm.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-BH12.5C1H1.01000.H is a Baumer EN380 series incremental encoder with optical sensing, a blind hollow shaft and a torque pin. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 1000 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, blind hollow shaft ø12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder slides onto a motor or gearbox shaft end and the torque pin holds the housing against rotation, so neither a coupling nor a separate bracket is needed. Permissible speed is 6000 rpm up to +75 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-BG12.5C2T1.02000.H is a Baumer EN380 series incremental encoder with optical sensing, a blind hollow shaft and a torque pin. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 2000 pulses per revolution
• Output: TTL/RS422, channels A, B and reference R with inverted signals, up to 300 kHz
• Supply: 5 VDC ±5 %, 60 mA without load
• Housing: aluminium, blind hollow shaft ø12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 2 m radial cable, 8 x 0.14 mm², open cable end

The encoder slides onto a motor or gearbox shaft end and the torque pin holds the housing against rotation, so neither a coupling nor a separate bracket is needed. Permissible speed is 6000 rpm up to +75 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-BF12.5C1T1.01000.H is a Baumer EN380 series incremental encoder with optical sensing, a blind hollow shaft and a stator coupling. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 1000 pulses per revolution
• Output: TTL/RS422, channels A, B and reference R with inverted signals, up to 300 kHz
• Supply: 5 VDC ±5 %, 60 mA without load
• Housing: aluminium, blind hollow shaft ø12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder slides onto a motor or gearbox shaft end and the stator coupling holds the housing against rotation, so neither a coupling nor a separate bracket is needed. Permissible speed is 6000 rpm up to +75 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-BF12.5C1T1.00250.H is a Baumer EN380 series incremental encoder with optical sensing, a blind hollow shaft and a stator coupling. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 250 pulses per revolution
• Output: TTL/RS422, channels A, B and reference R with inverted signals, up to 300 kHz
• Supply: 5 VDC ±5 %, 60 mA without load
• Housing: aluminium, blind hollow shaft ø12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder slides onto a motor or gearbox shaft end and the stator coupling holds the housing against rotation, so neither a coupling nor a separate bracket is needed. Permissible speed is 6000 rpm up to +75 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-BF12.5C1H1.00500.H is a Baumer EN380 series incremental encoder with optical sensing, a blind hollow shaft and a stator coupling. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 500 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, blind hollow shaft ø12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder slides onto a motor or gearbox shaft end and the stator coupling holds the housing against rotation, so neither a coupling nor a separate bracket is needed. Permissible speed is 6000 rpm up to +75 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-TG06.5C1H1.02048.H is a Baumer EN380 series incremental encoder with optical sensing, a through hollow shaft and a torque pin. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 2048 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, through hollow shaft ø6 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The shaft passes right through the encoder, so it also fits where the shaft continues on both sides, and the torque pin holds the housing against rotation. Permissible speed is 6000 rpm up to +60 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-TG06.5C1H1.00360.H is a Baumer EN380 series incremental encoder with optical sensing, a through hollow shaft and a torque pin. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 360 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, through hollow shaft ø6 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The shaft passes right through the encoder, so it also fits where the shaft continues on both sides, and the torque pin holds the housing against rotation. Permissible speed is 6000 rpm up to +60 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-TF06.5C1H1.02048.H is a Baumer EN380 series incremental encoder with optical sensing, a through hollow shaft and a stator coupling. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 2048 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, through hollow shaft ø6 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The shaft passes right through the encoder, so it also fits where the shaft continues on both sides, and the stator coupling holds the housing against rotation. Permissible speed is 6000 rpm up to +60 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-TF06.5C1H1.01024.H is a Baumer EN380 series incremental encoder with optical sensing, a through hollow shaft and a stator coupling. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 1024 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, through hollow shaft ø6 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The shaft passes right through the encoder, so it also fits where the shaft continues on both sides, and the stator coupling holds the housing against rotation. Permissible speed is 6000 rpm up to +60 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

AFI4-5D30.4006.1300 is a Baumer CombiLyz inductive conductivity sensor with display and bottom process connection. It passes conductivity and temperature on as two separate 4...20 mA signals, and over IO-Link 1.1 the same readings and the sensor settings are also available digitally.

• Measuring range: 14 selectable ranges, 0...500 µS/cm to 0...1000 mS/cm; temperature -20...150 °C
• Output: 2 x 4...20 mA (conductivity, temperature), 2 solid-state relays, IO-Link 1.1
• Supply: 15...35 V DC (18...30 V DC with IO-Link)
• Housing: FlexHousing Ø80 mm, AISI 304, G 1 A hygienic connection, PEEK Natura probe L=60 mm
• Environment: IP67 / IP69K; process -20...140 °C (up to 150 °C for less than 1 h), up to 25 bar
• Connection: 1 x M12-A, 5-pin + 1 x M12-A, 8-pin, stainless steel AISI 304

Used for concentration control of CIP solutions and for phase separation between product, water and cleaning solution in dairy, brewery and beverage lines. The minimum measurable conductivity is 50 µS/cm, so the sensor does not suit demineralised or purified water.

cULus listed (E491206); wetted parts in PEEK Natura comply with FDA 21 CFR 177.2415.