UWT NivoRadar NR 7200 is an 80 GHz FMCW radar level sensor for continuous, non-contact measurement of liquids up to 15 m. The narrow 8° beam avoids reflections from tank walls and internal fittings, and only the PVDF antenna is in contact with the medium.

• Measuring range: 0...15 m, accuracy ±2 mm
• Output: 2-wire 4...20 mA with HART
• Supply: 15...35 V DC, loop-powered
• Housing: PBT, G 1 1/2" thread (DIN ISO 228-1), PVDF wetted parts
• Environment: IP66/IP67, process temperature -40...+80 °C, pressure -1...+3 bar
• Connection: M20x1.5 cable gland
• Setup: display with push buttons under a transparent lid, or UWT LevelApp via Bluetooth

Used for level in storage and process tanks, IBCs and wastewater sumps, including many acids. Measures liquids with a dielectric constant from 1.1 - oils and solvents as well as water-based media.

CE, UKCA and cFMus approved for general-purpose (non-Ex) areas.

AFI5-A813.4002.0300 is a Baumer CombiLyz inductive conductivity sensor with separate electronics: the probe with its G 1 A connection sits in the pipe, and the housing with display is wall-mounted up to 10 m away. It passes conductivity and temperature on as two separate 4...20 mA signals, and both solid-state relays in the display can be set as limit contacts.

• Measuring range: 14 selectable ranges, 0...500 µS/cm to 0...1000 mS/cm; temperature -20...150 °C
• Output: 2 x 4...20 mA (conductivity, temperature), 2 solid-state relays
• Supply: 15...35 V DC
• Housing: FlexHousing Ø80 mm, AISI 304, wall mounting, G 1 A hygienic connection, PEEK Natura probe L=60 mm
• Environment: IP67 / IP69K; process -20...140 °C (up to 150 °C for less than 1 h), up to 25 bar
• Connection: 2 x M16x1.5 cable glands, plastic; 10 m PUR sensor cable

Used for concentration control of CIP solutions and for phase separation between product, water and cleaning solution in dairy, brewery and beverage lines. The minimum measurable conductivity is 50 µS/cm, so the sensor does not suit demineralised or purified water. The split design keeps the electronics away from hot or hard-to-reach pipe sections.

cULus listed (E491206); wetted parts in PEEK Natura comply with FDA 21 CFR 177.2415.

AFI4-5830.4002.0200 is a Baumer CombiLyz inductive conductivity sensor with display and bottom process connection. It passes conductivity and temperature on as two separate 4...20 mA signals, and both solid-state relays in the display can be set as limit contacts.

• Measuring range: 14 selectable ranges, 0...500 µS/cm to 0...1000 mS/cm; temperature -20...150 °C
• Output: 2 x 4...20 mA (conductivity, temperature), 2 solid-state relays
• Supply: 15...35 V DC
• Housing: FlexHousing Ø80 mm, AISI 304, G 1 A hygienic connection, PEEK Natura probe L=83 mm
• Environment: IP67 / IP69K; process -20...140 °C (up to 150 °C for less than 1 h), up to 25 bar
• Connection: 2 x M16x1.5 cable glands, stainless steel AISI 304

Used for concentration control of CIP solutions and for phase separation between product, water and cleaning solution in dairy, brewery and beverage lines. The minimum measurable conductivity is 50 µS/cm, so the sensor does not suit demineralised or purified water.

cULus listed (E491206); wetted parts in PEEK Natura comply with FDA 21 CFR 177.2415.

Nickel plated alloysteel IP67, “S” type load cel Output: 2.0 ± 0.004 mV/V Combined error: ≤± 0.020 %FS, Supply voltage: 5...12 VDC, Shielded 4-wire cable, 3m