EIL580P-SC10.7BF.01024.B is a Baumer optoPulse programmable incremental encoder with optical sensing. Pulse count from 1 to 65536, TTL or HTL output level, zero pulse width and position and signal sequence are set on site, so one encoder replaces several fixed-resolution models.

• Resolution: 1...65536 pulses per revolution, factory setting 1024
• Output: TTL/RS422 (factory setting) or HTL/push-pull, 6 channels, up to 300 kHz (TTL)
• Supply: 4.75-30 V DC, no-load consumption ≤70 mA
• Housing: Ø58 mm, clamping flange, Ø10 x 20 mm shaft with flat
• Environment: IP67 (with shaft seal), -40...+100 °C, up to 6000 rpm
• Connection: M12 8-pin radial connector

Parameters are set with the Baumer Z-PA-EI-H or Z-PA-EI-P programming tool and an M12/D-SUB connection cable. Unprogrammed, the encoder runs at 1024 pulses with a 5 V TTL output.

UL 508 / CSA 22.2 approved. EMC to EN 61000-6-2 and EN 61000-6-3; vibration (30 g, 10-2000 Hz) and shock (300 g, 6 ms) resistance to EN 60068-2-6 and EN 60068-2-27.

EIL580-S1B1.7FE.01024.A is a Baumer optoPulse incremental encoder with optical sensing, 1024 pulses per revolution and a EURO flange B10. The flange, with a Ø85 mm centring collar and six Ø6.6 mm holes on a Ø100 mm pitch circle, matches EURO B10 motor and gearbox mounting.

• Resolution: 1024 pulses per revolution, zero pulse
• Output: TTL/RS422, 6 channels (A+, B+, R+, A-, B-, R-), up to 300 kHz
• Supply: 5 V DC ±5 %, no-load consumption ≤70 mA
• Housing: EURO flange B10 (Ø115 mm), Ø11 x 30 mm shaft with Woodruff key
• Environment: IP67 (with shaft seal), -40...+85 °C, up to 6000 rpm
• Connection: M23 12-pin radial connector

The encoder needs a regulated 5 V supply and cannot be connected directly to a 24 V circuit. The shaft needs a flexible coupling, as permitted load is 40 N axial and 80 N radial.

UL 508 / CSA 22.2 approved. EMC to EN 61000-6-2 and EN 61000-6-3; vibration (30 g, 10-2000 Hz) and shock (300 g, 6 ms) resistance to EN 60068-2-6 and EN 60068-2-27.

EIL580-SY06.5EQ.01000.A is a Baumer optoPulse incremental encoder with optical sensing, 1000 pulses per revolution and synchro flange mounting. The HTL output level follows the supply (Vout = Vin), so on a 24 V system the signal is at 24 V and goes straight to a PLC high-speed counter input.

• Resolution: 1000 pulses per revolution, zero pulse
• Output: HTL/push-pull, 6 channels (A+, B+, R+, A-, B-, R-), up to 160 kHz
• Supply: 4.75-30 V DC, no-load consumption ≤70 mA
• Housing: Ø58 mm, synchro flange with Ø50 mm centring collar, Ø6 x 10 mm shaft with flat
• Environment: IP65, -40...+85 °C, up to 12000 rpm

The synchro flange lets the encoder be held with clamps and rotated around its shaft before tightening. The shaft needs a flexible coupling.

UL 508 / CSA 22.2 approved. EMC to EN 61000-6-2 and EN 61000-6-3; vibration (30 g, 10-2000 Hz) and shock (300 g, 6 ms) resistance to EN 60068-2-6 and EN 60068-2-27.

MHRM 12G5501 is a Baumer Hall-effect gearwheel sensor that detects the teeth of ferromagnetic gears from module 1 upwards. It has one push-pull output with a switching frequency of up to 15 kHz.

• Working distance: max. 0.7 mm at module 1, max. 2.4 mm at module 3
• Gear: ferromagnetic, module 1 or larger, width over 6 mm
• Output: push-pull, 30 mA, voltage drop below 5 VDC at 15 mA; switching frequency 0...15 kHz
• Supply: 8...28 VDC, max. 20 mA without load; short-circuit and reverse-polarity protected
• Housing: cylindrical threaded, Ø12 mm, 50 mm long, nickel-plated brass, PBTP sensing face
• Environment: IP67, -40...+85 °C
• Connection: 2 m PUR cable

Mounting is rotationally symmetric: the sensor's position about its own axis relative to the gear does not need aligning.

CE and UL approved.

EIL580-SC10.5FH.01024.A is a Baumer optoPulse incremental encoder with optical sensing and 1024 pulses per revolution. It runs on an 8-30 V DC supply while the output stays at 5 V TTL/RS422 level, so it connects to an RS422 input on a machine that only has 24 V available.

• Resolution: 1024 pulses per revolution, zero pulse
• Output: TTL/RS422, 6 channels (A+, B+, R+, A-, B-, R-), up to 300 kHz
• Supply: 8-30 V DC, no-load consumption ≤70 mA
• Housing: Ø58 mm, clamping flange with Ø36 mm centring collar, Ø10 x 20 mm shaft with flat
• Environment: IP65, -40...+85 °C, up to 12000 rpm
• Connection: M23 12-pin radial connector

Used for motor speed and position feedback where the controller or frequency converter has an RS422 input. Permitted shaft load is 40 N axial and 80 N radial, so the shaft needs a flexible coupling.

UL 508 / CSA 22.2 approved. EMC to EN 61000-6-2 and EN 61000-6-3; vibration (30 g, 10-2000 Hz) and shock (300 g, 6 ms) resistance to EN 60068-2-6 and EN 60068-2-27.

EN380.IL-SMA6.5C1H1.00250.H is a Baumer EN380 series incremental encoder with optical sensing, a synchro flange and a solid shaft. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 250 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, synchro flange, stainless steel shaft ø6 x 12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder mounts on a motor or gearbox shaft end through a flexible coupling, and the synchro flange fits it into a tight installation without a separate mounting plate. Permissible speed is 8000 rpm.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-SMA5.5C1T1.01024.H is a Baumer EN380 series incremental encoder with optical sensing, a synchro flange and a solid shaft. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 1024 pulses per revolution
• Output: TTL/RS422, channels A, B and reference R with inverted signals, up to 300 kHz
• Supply: 5 VDC ±5 %, 60 mA without load
• Housing: aluminium, synchro flange, stainless steel shaft ø5 x 12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder mounts on a motor or gearbox shaft end through a flexible coupling, and the synchro flange fits it into a tight installation without a separate mounting plate. Permissible speed is 8000 rpm.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-SMA5.5C1T1.00500.H is a Baumer EN380 series incremental encoder with optical sensing, a synchro flange and a solid shaft. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 500 pulses per revolution
• Output: TTL/RS422, channels A, B and reference R with inverted signals, up to 300 kHz
• Supply: 5 VDC ±5 %, 60 mA without load
• Housing: aluminium, synchro flange, stainless steel shaft ø5 x 12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder mounts on a motor or gearbox shaft end through a flexible coupling, and the synchro flange fits it into a tight installation without a separate mounting plate. Permissible speed is 8000 rpm.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-SMA5.5C1T1.00360.H is a Baumer EN380 series incremental encoder with optical sensing, a synchro flange and a solid shaft. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 360 pulses per revolution
• Output: TTL/RS422, channels A, B and reference R with inverted signals, up to 300 kHz
• Supply: 5 VDC ±5 %, 60 mA without load
• Housing: aluminium, synchro flange, stainless steel shaft ø5 x 12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder mounts on a motor or gearbox shaft end through a flexible coupling, and the synchro flange fits it into a tight installation without a separate mounting plate. Permissible speed is 8000 rpm.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-SMA5.5C1H1.00500.H is a Baumer EN380 series incremental encoder with optical sensing, a synchro flange and a solid shaft. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 500 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, synchro flange, stainless steel shaft ø5 x 12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder mounts on a motor or gearbox shaft end through a flexible coupling, and the synchro flange fits it into a tight installation without a separate mounting plate. Permissible speed is 8000 rpm.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-SMA5.5C1H1.00360.H is a Baumer EN380 series incremental encoder with optical sensing, a synchro flange and a solid shaft. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 360 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, synchro flange, stainless steel shaft ø5 x 12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder mounts on a motor or gearbox shaft end through a flexible coupling, and the synchro flange fits it into a tight installation without a separate mounting plate. Permissible speed is 8000 rpm.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-SMA5.5C1H1.00100.H is a Baumer EN380 series incremental encoder with optical sensing, a synchro flange and a solid shaft. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 100 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, synchro flange, stainless steel shaft ø5 x 12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder mounts on a motor or gearbox shaft end through a flexible coupling, and the synchro flange fits it into a tight installation without a separate mounting plate. Permissible speed is 8000 rpm.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-BH12.5C1H1.01000.H is a Baumer EN380 series incremental encoder with optical sensing, a blind hollow shaft and a torque pin. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 1000 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, blind hollow shaft ø12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder slides onto a motor or gearbox shaft end and the torque pin holds the housing against rotation, so neither a coupling nor a separate bracket is needed. Permissible speed is 6000 rpm up to +75 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-BG12.5C2T1.02000.H is a Baumer EN380 series incremental encoder with optical sensing, a blind hollow shaft and a torque pin. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 2000 pulses per revolution
• Output: TTL/RS422, channels A, B and reference R with inverted signals, up to 300 kHz
• Supply: 5 VDC ±5 %, 60 mA without load
• Housing: aluminium, blind hollow shaft ø12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 2 m radial cable, 8 x 0.14 mm², open cable end

The encoder slides onto a motor or gearbox shaft end and the torque pin holds the housing against rotation, so neither a coupling nor a separate bracket is needed. Permissible speed is 6000 rpm up to +75 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-BF12.5C1T1.01000.H is a Baumer EN380 series incremental encoder with optical sensing, a blind hollow shaft and a stator coupling. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 1000 pulses per revolution
• Output: TTL/RS422, channels A, B and reference R with inverted signals, up to 300 kHz
• Supply: 5 VDC ±5 %, 60 mA without load
• Housing: aluminium, blind hollow shaft ø12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder slides onto a motor or gearbox shaft end and the stator coupling holds the housing against rotation, so neither a coupling nor a separate bracket is needed. Permissible speed is 6000 rpm up to +75 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-BF12.5C1T1.00250.H is a Baumer EN380 series incremental encoder with optical sensing, a blind hollow shaft and a stator coupling. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 250 pulses per revolution
• Output: TTL/RS422, channels A, B and reference R with inverted signals, up to 300 kHz
• Supply: 5 VDC ±5 %, 60 mA without load
• Housing: aluminium, blind hollow shaft ø12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder slides onto a motor or gearbox shaft end and the stator coupling holds the housing against rotation, so neither a coupling nor a separate bracket is needed. Permissible speed is 6000 rpm up to +75 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-BF12.5C1H1.00500.H is a Baumer EN380 series incremental encoder with optical sensing, a blind hollow shaft and a stator coupling. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 500 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, blind hollow shaft ø12 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The encoder slides onto a motor or gearbox shaft end and the stator coupling holds the housing against rotation, so neither a coupling nor a separate bracket is needed. Permissible speed is 6000 rpm up to +75 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-TG06.5C1H1.02048.H is a Baumer EN380 series incremental encoder with optical sensing, a through hollow shaft and a torque pin. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 2048 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, through hollow shaft ø6 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The shaft passes right through the encoder, so it also fits where the shaft continues on both sides, and the torque pin holds the housing against rotation. Permissible speed is 6000 rpm up to +60 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-TG06.5C1H1.00360.H is a Baumer EN380 series incremental encoder with optical sensing, a through hollow shaft and a torque pin. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 360 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, through hollow shaft ø6 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The shaft passes right through the encoder, so it also fits where the shaft continues on both sides, and the torque pin holds the housing against rotation. Permissible speed is 6000 rpm up to +60 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-TF06.5C1H1.02048.H is a Baumer EN380 series incremental encoder with optical sensing, a through hollow shaft and a stator coupling. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 2048 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, through hollow shaft ø6 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The shaft passes right through the encoder, so it also fits where the shaft continues on both sides, and the stator coupling holds the housing against rotation. Permissible speed is 6000 rpm up to +60 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.

EN380.IL-TF06.5C1H1.01024.H is a Baumer EN380 series incremental encoder with optical sensing, a through hollow shaft and a stator coupling. Every channel also carries an inverted signal, so the encoder can be wired to a differential input and use a longer cable in electrically noisy surroundings.

• Resolution: 1024 pulses per revolution
• Output: HTL/push-pull, channels A, B and reference R with inverted signals, up to 160 kHz
• Supply: 8...30 VDC, 30 mA (24 VDC) without load
• Housing: aluminium, through hollow shaft ø6 mm
• Environment: IP 65, -25...+85 °C, vibration 10 g (10-2000 Hz), shock 100 g (2 ms)
• Connection: 1 m radial cable, 8 x 0.14 mm², open cable end

The shaft passes right through the encoder, so it also fits where the shaft continues on both sides, and the stator coupling holds the housing against rotation. Permissible speed is 6000 rpm up to +60 °C.

EMC compliance to EN 61000-6-2 and EN 61000-6-4. UL-Listing E217823.