TL50RALS is a Banner TL50 series 50 mm tower light with one red segment and a sealed audible element. The light and the alarm have separate input wires, and the inputs act as PNP or NPN depending on the wiring.

• Color: red, 625 nm
• Audible: sealed, steady tone 2.9 kHz, 94 dB at 1 m, adjustable by about 20 dB by turning the front cover
• Inputs: bimodal PNP/NPN, response time max. 10 ms
• Supply: 18...30 V DC or 24 V AC ±3 V, 50/60 Hz; max. 45 mA light, 35 mA alarm
• Housing: ABS base and cover, polycarbonate segment, Ø50 x 134 mm, M30x1.5 thread
• Environment: IP67, UL 4X (indoor) and 13, -20...+50 °C
• Connection: 2 m PVC cable, 4 wires

CE compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

TL50ALS is a Banner TL50 series audible indicator in a 50 mm tower housing with a sealed audible element and no light segments. It runs on DC or 24 V AC and switches with a bimodal PNP or NPN input.

• Audible: continuous tone 2.9 kHz, up to 94 dB at 1 m, about 20 dB reduction when turned down
• Input: bimodal PNP/NPN, response time 10 ms
• Supply: 12...30 V DC or 24 V AC ±3 V (50...60 Hz), 35 mA
• Housing: black ABS, M30x1.5 thread, Ø50 x 93.4 mm
• Environment: IP67, UL Type 4X Indoor and 13, -20...+50 °C
• Connection: 2 m PVC cable, 4 wires

Volume is set by rotating the front cover.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

LMB30RA is a Banner LMB series sealed right-angle bracket for indicators and sensors with a 30 mm threaded base. Gaskets and O-rings between the mounting surface, the base and the adapter give an IP67 installation, and the cable can be routed through the mounting surface.

• Included: base, 30 mm adapter, set screw, fasteners, O-rings and gaskets
• Device thread: M30 × 1.5
• Material: black polycarbonate
• Mounting: 3 × M5 screws (5.5 mm holes), 12.7 mm cable hole
• Protection rating: IP67 (assembled bracket)

The device is turned to the required orientation relative to the base and locked with the 8-32 set screw, tightened to 0.17 Nm max.

SMB30A is a Banner right-angle bracket for sensors with a 30 mm housing. The curved slot lets the sensor be turned before the screws are tightened.

• Sensor hole: Ø30.5 mm
• Mounting: M6 (¼") hardware, 40 mm hole centre spacing
• Material: 12-gauge stainless steel

K30LGRYPQ is a Banner K30L series 30 mm dome indicator with three LED colors driven by three separate PNP inputs. The electronics are fully encapsulated.

• Colors: green, red, yellow; one color on at a time
• Input: PNP, response time 1 ms
• Supply: 10...30 V DC, up to 25 mA per color
• Housing: polycarbonate, M22x1.5 threaded base, 30 x 57 mm
• Environment: IP67, IP69K, UL 4X and 13, -40...+50 °C
• Connection: integral 4-pin M12 male connector

The M22 base fits the standard 22 mm panel cut-out used for pushbuttons and pilot lights. IP69K lets the indicator stay in place during high-pressure washdown.

K50APFF100GRCQ is a Banner K50 series pick-to-light device: a 50 mm dome that lights green as a job light and an infrared fixed-field sensor with a 100 mm cutoff. When a hand enters the field the PNP output switches and the dome turns red to confirm the pick.

• Sensing: fixed field, 100 mm cutoff, infrared 880 nm, ambient light up to 5000 lux
• Output: PNP, normally open, max. 150 mA, response 3 ms
• Indicator: green job light (job input), red when a hand is sensed
• Supply: 12...30 V DC, < 75 mA at 12 V; AS-i compatible
• Housing: fully encapsulated, polycarbonate, M30x1.5 thread
• Environment: IP67 (IP69K with IP69K cordset), Type 4X and 13, -40...+50 °C
• Connection: integral 4-pin M12 male connector

Used on picking racks and assembly stations to show which bin to take from and to confirm the pick without a separate sensor.

CL50GRYALSPQ is a Banner CL50 series 50 mm column light with three LED segments and a sealed loud audible alarm. Each color and the audible are switched by a separate PNP input.

• Colors: green (72 lm), red (38 lm), yellow (30 lm)
• Audible: continuous tone 2.9 kHz, up to 94 dB at 1 m, adjustable volume
• Input: PNP, response time 10 ms
• Supply: 18...30 V DC, per color 100 mA at 18 V and 70 mA at 30 V, audible 35 mA
• Housing: ABS base and covers, polycarbonate light segments, M30x1.5 thread, 50 x 168.2 mm
• Environment: IP67, UL 4X and 13, -20...+50 °C
• Connection: integral 5-pin M12 male connector

The column comes factory-assembled, so it mounts in a single M30 hole with no modules to stack. Volume is set by rotating the front cover.

CE and UL compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

K50LGRAL1YPQ is a Banner K50 series 50 mm three-color dome indicator with a loud steady audible alarm. Green, red, yellow and the alarm each have their own input wire, so they are switched independently by four PLC outputs.

• Colors: green, red, yellow
• Audible: steady tone 2.7 kHz, 95 dB at 1 m
• Inputs: PNP, response time max. 10 ms
• Supply: 18...30 V DC, max. 40 mA per color and alarm
• Housing: polycarbonate, M30x1.5 threaded base, Ø50 x 68 mm
• Environment: IP50, UL 4X and 13, -20...+50 °C
• Connection: integral 5-pin M12 male connector

The audible opening limits the rating to IP50, so the indicator is meant for locations without water spray. The base is fixed with the included M30 nut, max. torque 4.5 N·m.

CE compliant.

WLS28-2CW145XPBQ is a Banner WLS28-2 series 145 mm cool white work light with a High/Low/Off switch on the housing. It is a cascade model: further lights connect to it with double-ended cordsets, and the switch controls them too.

• Light: cool white 6500 K, 400 lm, CRI 85
• Switch: II - 100 %, I - 50 %, 0 - off
• Supply: 12...30 V DC, typical 0.15 A at 24 V
• Housing: anodized aluminum, clear polycarbonate window, 224 x 28 x 25 mm, two swivel brackets included
• Environment: IP50, -40...+70 °C, light output decreases above +50 °C
• Connection: integral 4-pin M12 male connector

In a cascade at 100 % intensity the total light length must not exceed 1.4 m at 12 V DC and 3.0 m at 24 V DC; at 50 % intensity the lengths double. LED lifetime L70 - 75,000 hours.

CE compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

Supplied without original packaging.

K30ALBTYRHQ is a Banner K30 series 30 mm capacitive touch button with a latching output. It glows yellow when not activated and red when activated, and each touch toggles the state.

• Function: latching, starts up not activated; output response 150 ms
• Output: bipolar (one PNP and one NPN), normally open, max. 150 mA
• Supply: 12...30 V DC, 55 mA, reverse polarity protected
• Housing: polycarbonate base and dome, M22x1.5 thread, Ø30 x 54.5 mm
• Environment: IP67, IP69K, Type 4X and 13, -40...+50 °C
• Connection: integral 5-pin M12 male connector

The button needs no actuation force and works with bare hands or gloves, which suits washdown areas where mechanical push buttons wear out.

Vibration per MIL-STD-202F method 201A, shock per IEC 60947-5-2 (30 G, 11 ms).

K50LGRA1YP is a Banner K50L series 50 mm dome indicator with three LED colors and an audible alarm. Each color and the audible have their own PNP input.

• Colors: green, red, yellow; one color on at a time
• Audible: continuous tone 3 kHz, 75 dB at 1 m
• Input: PNP, response time 10 ms
• Supply: 18...30 V DC, up to 40 mA per color or audible
• Housing: polycarbonate, M30x1.5 threaded base, 50 x 57 mm
• Environment: IP50, NEMA/UL 4X and 13, -20...+50 °C
• Connection: integral 2 m PVC cable, 5 wires

The housing is rated IP50, so the indicator is meant for dry rooms and control panels rather than washdown machinery.

K50LGRALSYPQ is a Banner K50L series sealed 50 mm dome indicator with three LED colors and a loud audible alarm. Each color and the audible have their own PNP input, so they can be switched independently from controller outputs.

• Colors: green, red, yellow; one color on at a time
• Audible: continuous tone 2.9 kHz, up to 94 dB at 1 m, adjustable volume
• Input: PNP, response time 1 ms (LED) and 10 ms (audible)
• Supply: 12...30 V DC, up to 35 mA per color at 30 V (65 mA at 12 V), audible 35 mA
• Housing: polycarbonate, M30x1.5 threaded base, 50 x 73 mm
• Environment: IP67, NEMA/UL 4X and 13, -20...+50 °C
• Connection: integral 5-pin M12 male connector

Volume is set by rotating the front cover, so one model suits both a quiet room and a noisy machine. The supply circuit is protected against reverse polarity and transient voltages.

CE and UL compliant. Vibration per MIL-STD-202F (Method 201A), shock per IEC 60947-5-2 (30 G, 11 ms).

B-TL70-5 is a Banner TL70 series 70 mm modular tower light base that takes up to four SG-TL70 light or audible modules. Each module has its own input, which works with either a PNP or NPN signal.

• Modules: 1...4 SG-TL70 modules, each with a separate input
• Inputs: bimodal PNP/NPN, turn-on time up to 180 ms at 12 V
• Supply: 12...30 V DC
• Housing: polycarbonate, M30x1.5 threaded base, Ø70 x 47.5 mm
• Environment: IP65, -40...+50 °C
• Connection: integral 2 m PVC cable, 5 wires

Each module's position in the tower and its flashing are set with DIP switches in the module, so modules can be rearranged in the field. The base has no light of its own - the tower needs light modules ordered with it.

CE, UKCA and UL compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

B-TL70-Q5 is a Banner TL70 series 70 mm modular tower light base that takes up to four SG-TL70 light or audible modules. Each module has its own input, which works with either a PNP or NPN signal.

• Modules: 1...4 SG-TL70 modules, each with a separate input
• Inputs: bimodal PNP/NPN, turn-on time up to 180 ms at 12 V
• Supply: 12...30 V DC
• Housing: polycarbonate, M30x1.5 threaded base, Ø70 x 47.5 mm
• Environment: IP65, -40...+50 °C
• Connection: integral 5-pin M12 male connector

Each module's position in the tower and its flashing are set with DIP switches in the module, so modules can be rearranged in the field. The base has no light of its own - the tower needs light modules ordered with it.

CE, UKCA and UL compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

SG-TL70-Y is a Banner TL70 series yellow 70 mm light module for a modular tower light. When off the segment looks gray, so ambient light does not make it appear lit.

• Color: yellow, 590 nm, 22 lm
• Mode: steady or flashing 1.5 Hz / 3 Hz, selected with DIP switches
• Supply: 12...30 V DC, 285 mA at 12 V, 145 mA at 24 V
• Housing: black polycarbonate, Ø70 x 50 mm
• Environment: IP65, -40...+50 °C

The module twist-locks onto a B-TL70 series base, which carries the electrical connection. The DIP switches set the module's position in the tower (1...6), so it can be moved to another position without rewiring.

CE and UKCA compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

SG-TL70-R is a Banner TL70 series red 70 mm light module for a modular tower light. When off the segment looks gray, so ambient light does not make it appear lit.

• Color: red, 625 nm, 40 lm
• Mode: steady or flashing 1.5 Hz / 3 Hz, selected with DIP switches
• Supply: 12...30 V DC, 285 mA at 12 V, 145 mA at 24 V
• Housing: black polycarbonate, Ø70 x 50 mm
• Environment: IP65, -40...+50 °C

The module twist-locks onto a B-TL70 series base, which carries the electrical connection. The DIP switches set the module's position in the tower (1...6), so it can be moved to another position without rewiring.

CE and UKCA compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

SG-TL70-A is a Banner TL70 series standard audible module for a modular tower light. One module offers four alarm patterns, and the volume is set by turning the cover.

• Sound: 2.6 kHz, up to 98 dB at 1 m (typical), adjustment range about 8 dB
• Pattern: continuous, pulsed 1.5 Hz, chirp or siren, selected with DIP switches
• Supply: 12...30 V DC, 30 mA
• Housing: black polycarbonate, Ø70 x 72 mm
• Environment: IP65, -40...+50 °C

The module twist-locks onto a B-TL70 series base, which carries the electrical connection. DIP switches set the module's position in the tower (1...6) and the alarm pattern.

CE and UKCA compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

SG-TL70-G is a Banner TL70 series green 70 mm light module for a modular tower light. When off the segment looks gray, so ambient light does not make it appear lit.

• Color: green, 525 nm, 92 lm
• Mode: steady or flashing 1.5 Hz / 3 Hz, selected with DIP switches
• Supply: 12...30 V DC, 420 mA at 12 V, 200 mA at 24 V
• Housing: polycarbonate, Ø70 x 50 mm
• Environment: IP65, -40...+50 °C

The module twist-locks onto a B-TL70 series base. The DIP switches also set the module's position in the tower (1...6), so it can be moved to another position without rewiring.

CE, UKCA and UL compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

K50APT2GRYF2Q is a Banner K50 Touch Gen 2 series 50 mm illuminated touch button with a momentary PNP output. The dome shows three independently switched colors, with yellow overriding red and red overriding green.

• Colors: green 525 nm (29 lm), red 625 nm (13 lm), yellow 591 nm (24 lm), one PNP input per color
• Output: PNP, normally open, momentary, max. 150 mA, response 50 ms
• Supply: 12...30 V DC, < 75 mA at 12 V
• Housing: polycarbonate base and dome, PBT nut, M30x1.5 thread, Ø50 x 66 mm
• Environment: IP67, IP69K, -40...+50 °C
• Connection: integral 8-pin M12 male connector

If a touch lasts longer than 60 seconds, the output and color return to the untouched state, so a resting object does not hold the signal.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

TL50GRQ is a Banner TL50 series 50 mm two-segment tower light with green (bottom) and red (top) segments. It comes assembled and each color is switched by its own bimodal input.

• Colors: green 525 nm (17 lm), red 625 nm (8 lm)
• Input: bimodal PNP/NPN, response 1 ms
• Supply: 18...30 V DC, 26 mA per segment
• Housing: polycarbonate, M30x1.5 thread, Ø50 x 137.4 mm; knurled nut and gasket included
• Environment: IP67, UL Type 4X, -40...+50 °C
• Connection: integral 4-pin M12 male connector

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

TL50HGYRQP is a Banner TL50H series high-brightness 50 mm tower light with green, yellow and red segments, for areas with strong ambient light. It comes assembled and each color is switched by its own bimodal input.

• Colors (bottom to top): green 525 nm (60 lm), yellow 590 nm (23 lm), red 625 nm (32 lm)
• Input: bimodal PNP/NPN, response 10 ms
• Supply: 18...30 V DC or 24 V AC; per color 100 mA at 18 V, 60 mA at 30 V
• Housing: ABS base and covers, polycarbonate segments, M30x1.5 thread, Ø50 x 161.5 mm
• Environment: IP67, UL Type 4X Indoor and 13, -40...+50 °C
• Connection: 150 mm PVC cable with 4-pin M12 male connector

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

B-TL70Z-Q5 is the AC base module of the Banner TL70 modular tower light, for towers of one to four modules. Each module is switched by its own 100...240 V AC hot wire through the base connector.

• Supply: 100...240 V AC, 50/60 Hz; max. 50 mA per module at 230 V AC
• Modules: 1-4 light or audible modules, position set with DIP switches in each module
• Mode: steady or flashing at 1.5 Hz or 3 Hz, set per module
• Housing: polycarbonate, internal 1/2-14 NPSM mounting thread
• Environment: IP65, -40...+50 °C
• Connection: integral 1/2"-20UNF male quick-disconnect connector, 5 pins

The base takes the same light and audible modules as the DC TL70, so the tower wires straight to 230 V AC control outputs. The base tolerates up to 500 µA leakage current; solid-state PLC outputs often exceed 1 mA, which keeps a module lit in the off state. In that case use relay outputs or fit a shunt resistor between the neutral wire and the hot wire of each channel.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

K50L2RGB7ALSQ is a Banner K50 Pro series 50 mm RGB dome indicator with a sealed loud audible alarm. Combinations of three inputs give seven colors, and the fourth, gray wire switches the audible.

• Colors: green, red, yellow, blue, white, cyan, magenta
• Audible: continuous tone 2.9 kHz, 94 dB at 1 m
• Inputs: bimodal PNP/NPN, response time 250 ms
• Supply: 10...30 V DC, 220 mA at 10 V, 115 mA at 24 V
• Housing: polycarbonate, M30x1.5 threaded base, 50 x 73 mm
• Environment: IP67, UL 4X and 13, -40...+50 °C
• Connection: integral 5-pin M12 male connector

Whether the inputs act as PNP or NPN depends only on the wiring. Colors and animations can be reprogrammed with Banner Pro Editor software and a Pro Converter cable.

CE and UL compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

SA-M30 is a Banner cover that hides the outer M30 thread on a light's base.

• Fits: devices with an M30 base, Banner lists TL70 tower lights and the K90 series
• Material: black polycarbonate
• Included: mounting hardware

SOP-E12-150A is a Banner 150 mm stand-off pipe for mounting an indicator, tower light or sensor elevated above the mounting surface.

• Length: 150 mm
• Thread: ½" NPT at both ends (NPSM/DN15)
• Material: black anodised aluminium

The lower end of the pipe needs a mounting base and the upper end an adapter for the device's base.

SA-F12-3 is a Banner elevated mount system base that fixes a ½" stand-off pipe to a flat surface with three screws.

• Connection: ½" NPSM/DN15 pipe
• Dimensions: Ø70 mm, 3 mounting holes
• Material: black polycarbonate
• Included: M4 mounting hardware and nitrile blend gasket

SA-M22E12 is a Banner adapter that connects a light's 22 mm base to a ½" stand-off pipe for elevated mounting. Banner specifies it for TL30 tower lights.

• Connection: 22 mm device base - ½" NPSM/DN15 pipe
• Material: black polycarbonate
• Mounting hardware: not included

SMBWLS28RA is a Banner replacement end bracket kit for WLS28 LED lights.

• Included: 2 end brackets and 4 screws
• Material: 1.8 mm (14-gauge) cold-rolled steel
• Finish: zinc plate with clear chromate

K50LGRALSYPQP is a Banner K50L series sealed 50 mm dome indicator with three LED colors and a loud audible alarm. Each color and the audible have their own PNP input, so they can be switched independently from controller outputs.

• Colors: green, red, yellow; one color on at a time
• Audible: continuous tone 2.9 kHz, up to 94 dB at 1 m, adjustable volume
• Input: PNP, response time 1 ms (LED) and 10 ms (audible)
• Supply: 12...30 V DC, up to 35 mA per color at 30 V (65 mA at 12 V), audible 35 mA
• Housing: polycarbonate, M30x1.5 threaded base, 50 x 62 mm
• Environment: IP67, NEMA/UL 4X and 13, -20...+50 °C
• Connection: 150 mm PVC cable with 5-pin M12 male connector

Volume is set by rotating the front cover, so one model suits both a quiet room and a noisy machine. The supply circuit is protected against reverse polarity and transient voltages.

CE and UL compliant. Vibration per MIL-STD-202F (Method 201A), shock per IEC 60947-5-2 (30 G, 11 ms).

K50PTAMGRY3Q is a Banner K50 Pro series 50 mm touch button with an RGB indicator and a momentary output. Two inputs select green, yellow or red, and colors, animation, output logic and touch sensitivity can be changed with Pro Editor software.

• Colors (default): green 522 nm (16.5 lm), yellow 576 nm (23.8 lm), red 620 nm (8.3 lm); up to 14 colors via Pro Editor
• Output: bipolar, normally open, momentary, max. 150 mA; input response 40 ms, output 300 ms
• Supply: 12...30 V DC, 93 mA at 24 V
• Housing: polycarbonate base, dome and nut, M30x1.5 thread, Ø50 x 66 mm
• Environment: IP67, IP69K, -40...+50 °C
• Connection: integral 5-pin M12 male connector

Programming needs the Pro Converter Cable and Pro Editor; one wire can be reassigned from input to output. Works with bare hands or gloves.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

SA-E12M30 is a Banner elevated mount system base adapter that fixes a ½" stand-off pipe in a surface with a 30 mm hole and covers the pipe end.

• Connection: ½" NPSM/DN15 pipe
• Mounting: in a 30 mm (1-3/16") hole
• Material: black acetal
• Included: mounting hardware

K50LGRALSYP is a Banner K50L series sealed 50 mm dome indicator with three LED colors and a loud audible alarm. Each color and the audible have their own PNP input, so they can be switched independently from controller outputs.

• Colors: green, red, yellow; one color on at a time
• Audible: continuous tone 2.9 kHz, up to 94 dB at 1 m, adjustable volume
• Input: PNP, response time 1 ms (LED) and 10 ms (audible)
• Supply: 12...30 V DC, up to 35 mA per color at 30 V (65 mA at 12 V), audible 35 mA
• Housing: polycarbonate, M30x1.5 threaded base, 50 x 62 mm
• Environment: IP67, NEMA/UL 4X and 13, -20...+50 °C
• Connection: integral 2 m PVC cable, 5 wires

Volume is set by rotating the front cover, so one model suits both a quiet room and a noisy machine. The supply circuit is protected against reverse polarity and transient voltages.

CE and UL compliant. Vibration per MIL-STD-202F (Method 201A), shock per IEC 60947-5-2 (30 G, 11 ms).

WLB32ZCWW850EPBQMB is a Banner WLB32 series 850 mm warm white AC light bar for machines, workstations and control cabinets. The eye shield blocks side glare, and each bar in a chain switches High/Low/Off independently of the others.

• Light: warm white 3000 K, 2250 lm
• Switch: II - 100 %, I - 50 %, O - standby
• Supply: 90...264 V AC, 50/60 Hz, typical 0.095 A at 230 V AC
• Housing: anodized aluminum, diffused polycarbonate window, 862 x 38.3 x 48 mm, snap clips
• Environment: IP50, -25...+45 °C
• Connection: integral connector, power cord with US NEMA 5-15 (Type B) plug included

Up to 16 bars can be chained with double-ended cordsets. The included cord has a US plug, so European sockets need a separate power cordset with a CEE 7/7 (Type E/F) plug.

CE and UKCA compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

PRO-KIT is a Banner kit for configuring Pro series lights and selected sensors from a PC with the Pro Editor software. It is needed for initial configuration only, not for the device's operation in the machine.

• Included: converter cable, splitter and power supply
• Software: Banner Pro Editor
• Fits: Banner Pro series lights and selected sensors

CE and UKCA compliant.

SP250GRPQ is a Banner EZ-LIGHT SP series two-signal traffic light with green and red indicators that stay readable in daylight. The narrow field of view and the included sun shield suit lane and entrance signalling.

• Colors: green 528 nm, 57 lm; red 625 nm, 20 lm
• Inputs: PNP, response time max. 10 ms
• Supply: 15...30 V DC, max. 120 mA per color
• Housing: polycarbonate, fully encapsulated, 192.8 x 87.6 x 109.6 mm
• Environment: IP65 (electronics IP67), -40...+50 °C
• Connection: integral 4-pin M12 male connector

CE compliant.

R70SR2MQ is a Banner Sure Cross R70SR serial data radio for the 2.4 GHz ISM band that carries RS-485 Modbus RTU traffic over a wireless link instead of a cable. Operating modes are set with DIP switches, and radios are paired with a binding button under the cover.

• Radio: 2.4 GHz FHSS, 65 mW (100 mW EIRP with the supplied 2 dB antenna), 250 kbps
• Communication: RS-485, Modbus RTU; default 19200 baud, no parity, changed via AT commands
• Network: serial or MultiHop mode; point-to-point, star and tree topologies
• Supply: 10...30 V DC (outside the USA 12...24 V DC ±10 %), 0.02 A at 24 V in client mode
• Housing: black polycarbonate base, translucent gray cover, Ø70 mm, M30x1 mount
• Environment: IP65, -40...+85 °C, up to 95 % RH non-condensing
• Connection: integral 5-pin M12 male connector for supply and RS-485

Serial mode suits cable replacement in point-to-point and small star networks without changing the Modbus addresses of connected devices; MultiHop mode builds a routing table for larger star and tree networks and works with other Sure Cross MultiHop radios. A link needs at least two radios. Never power the radio without an antenna fitted.

CE and UKCA, RED 2014/53/EU. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

SG-TL70-B is a Banner TL70 series blue 70 mm light module for a modular tower light. When off the segment looks gray, so ambient light does not make it appear lit.

• Color: blue, 470 nm, 32 lm
• Mode: steady or flashing 1.5 Hz / 3 Hz, selected with DIP switches
• Supply: 12...30 V DC, 420 mA at 12 V, 200 mA at 24 V
• Housing: black polycarbonate, Ø70 x 50 mm
• Environment: IP65, -40...+50 °C

The module twist-locks onto a B-TL70 series base, which carries the electrical connection. The DIP switches set the module's position in the tower (1...6), so it can be moved to another position without rewiring.

CE and UKCA compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

WLS15XDW0500DSQP is a Banner WLS15 series 500 mm daylight white strip light in a sealed polycarbonate shell with an aluminum frame. The same model runs on 12 V DC or 24 V DC.

• Light: daylight white 5000 K, 525 lm, lighted length 426.4 mm
• Supply: 12 or 24 V DC, typical 0.57 A at 12 V, 0.30 A at 24 V
• Dimming: PWM 25...100 %, up to 1000 Hz
• Housing: polycarbonate, aluminum frame, polyamide end caps, 500 x 30.6 x 15.5 mm
• Environment: IP66, IP67, -40...+60 °C
• Connection: 150 mm PVC cable with 4-pin M12 male connector, stand-alone (non-cascade) model

The light is fixed with M4 screws through the integral slots (max. 0.56 N·m) or with snap clips. The cable must not be exposed to a high-pressure jet.

CE compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

K50PTALGRY3Q is a Banner K50 Pro series 50 mm touch button with an RGB indicator and a latching output. Two inputs select green, yellow or red, and colors, animation, output logic and touch sensitivity can be changed with Pro Editor software.

• Colors (default): green 522 nm (16.5 lm), yellow 576 nm (23.8 lm), red 620 nm (8.3 lm); up to 14 colors via Pro Editor
• Output: bipolar, normally open, latching, max. 150 mA; input response 40 ms, output 300 ms
• Supply: 12...30 V DC, 93 mA at 24 V
• Housing: polycarbonate base, dome and nut, M30x1.5 thread, Ø50 x 66 mm
• Environment: IP67, IP69K, -40...+50 °C
• Connection: integral 5-pin M12 male connector

Programming needs the Pro Converter Cable and Pro Editor; one wire can be reassigned from input to output. Works with bare hands or gloves.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

- one-sided, width 30 cm - LED colour: red - RS485, Modbus RTU protocol - 24 VDC, IP52 - 2-line text "GAS ALARM LEAVE ROOM"

WL50SWSSL5Q is a Banner WL50S series LED spotlight with a 316 stainless steel housing and a ±5° lens, giving the smallest, most focused spot in the series. The light comes from three high-intensity white LEDs.

• Light: white 5000...8300 K, 295 lm; 13,780 lx at 0.5 m and 3,445 lx at 1 m
• Supply: 12...30 V DC, up to 400 mA
• Housing: 316 stainless steel, polycarbonate window with Viton seal, M30x1.5 base with stainless steel nut, Ø56 mm
• Environment: IP67, IP69K, -20...+50 °C
• Connection: integral 5-pin M12 male connector, only 2 wires used
• Useful life: light output drops by less than 30% after 50,000 hours

The narrow beam lights a specific work area on a machine, and the housing is chemically resistant and built for washdown machinery. The base gasket is FDA-grade silicone. The cable must not be hit with a high-pressure spray.

Vibration per MIL-STD-202F (Method 201A), shock per IEC 60947-5-2 (30 G, 11 ms).

WLS15XDW0360DSC2 is a Banner WLS15 series 360 mm daylight white strip light in a sealed polycarbonate shell with an aluminum frame. The same model runs on 12 V DC or 24 V DC.

• Light: daylight white 5000 K, 350 lm, lighted length 286.4 mm
• Supply: 12 or 24 V DC, typical 0.38 A at 12 V, 0.20 A at 24 V
• Dimming: PWM 25...100 %, up to 1000 Hz
• Housing: polycarbonate, aluminum frame, polyamide end caps, 360 x 30.6 x 15.5 mm
• Environment: IP66, IP67, -40...+60 °C
• Connection: 2 m PVC cable, 2 wires, stand-alone (non-cascade) model

The light is fixed with M4 screws through the integral slots (max. 0.56 N·m) or with snap clips. The cable must not be exposed to a high-pressure jet.

CE compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

WLF12PXRGB1200SQP is a Banner WLF12 Pro series flexible RGB LED strip with a 1200 mm lit length for status indication on machines, AGVs and workstations. Color, flashing, intensity and animations are set through an LC25 LED controller, which can be driven by discrete signals, IO-Link or Modbus.

• Colors: RGB, programmable through the LC25 controller
• Supply: 12 V DC ±10% without controller, 12...30 V DC with LC25 controller; current 0.78 A at 12 V
• Housing: clear silicone, 1225 x 12.8 x 6.4 mm, adhesive tape on the back, minimum bend radius 15 mm
• Environment: IP66, IP67, IP69K, -20...+45 °C
• Connection: 150 mm PVC cable with 4-pin M12 male connector

The strip needs an LC25 LED controller mounted no more than 3.05 m away. A supply above 12 V DC applied directly to the strip damages it permanently. The strip can be shortened at the cut lines every 50 mm, sealing the end with the supplied cap and silicone, but cutting voids the warranty. Not for applications with repeated flexing.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms). Suitable for damp locations per UL 2108.

LC25C-WLF12-RGB7Q is a Banner LC25 in-line controller that sits between a PLC and a WLF12 Pro flexible multicolor strip light. It converts discrete, PWM or PFM signals into colors, animations, levels or counters on the strip.

• Inputs: 3 discrete inputs, 12...30 V DC; PWM 0...100 % or PFM 100...10 000 Hz
• Modes: machine status, tower light, timer, counter, distance, gauge - set in Pro Editor
• Supply: 12...30 V DC, max. 30 mA (strip supplied separately)
• Housing: translucent black PVC, nickel-plated brass coupling, 25 x 85 mm
• Environment: IP65, IP67, IP68, -40...+50 °C
• Connection: integral 4-pin M12 male and female connectors

Required for WLF12 Pro: the strip must be no more than 3.05 m from the controller, and 24 V applied directly to the strip destroys it. The strip length is taught once by remote input or in Pro Editor.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

SG-TL70-W is a Banner TL70 series white 70 mm light module for a modular tower light. When off the segment looks gray, so ambient light does not make it appear lit.

• Color: daylight white, 5000 K, 125 lm
• Mode: steady or flashing 1.5 Hz / 3 Hz, selected with DIP switches
• Supply: 12...30 V DC, 420 mA at 12 V, 200 mA at 24 V
• Housing: black polycarbonate, Ø70 x 50 mm
• Environment: IP65, -40...+50 °C

The module twist-locks onto a B-TL70 series base, which carries the electrical connection. The DIP switches set the module's position in the tower (1...6), so it can be moved to another position without rewiring.

CE and UKCA compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

SG-TL70B-R is a Banner TL70B series red 70 mm light module for a modular tower light. When off the segment looks gray, so ambient light does not make it appear lit.

• Color: red, 625 nm, 24 lm
• Mode: steady or flashing 1.5 Hz / 3 Hz
• Supply: 12...30 V DC, 141 mA at 12 V, 71 mA at 24 V
• Housing: polycarbonate, Ø70 x 50 mm
• Environment: IP65, IP66, -40...+50 °C

The module twist-locks onto a TL70B series base. Unlike the TL70 series, the module has no settings of its own: it is driven by the base input that matches its position in the tower, and flashing is switched on with DIP switches in the base.

CE, UKCA and UL compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

SG-TL70B-G is a Banner TL70B series green 70 mm light module for a modular tower light. When off the segment looks gray, so ambient light does not make it appear lit.

• Color: green, 525 nm, 67 lm
• Mode: steady or flashing 1.5 Hz / 3 Hz
• Supply: 12...30 V DC, 141 mA at 12 V, 71 mA at 24 V
• Housing: polycarbonate, Ø70 x 50 mm
• Environment: IP65, IP66, -40...+50 °C

The module twist-locks onto a TL70B series base. Unlike the TL70 series, the module has no settings of its own: it is driven by the base input that matches its position in the tower, and flashing is switched on with DIP switches in the base.

CE, UKCA and UL compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

SG-TL70B-B is a Banner TL70B series blue 70 mm light module for a modular tower light. When off the segment looks gray, so ambient light does not make it appear lit.

• Color: blue, 475 nm, 25 lm
• Mode: steady or flashing 1.5 Hz / 3 Hz
• Supply: 12...30 V DC, 204 mA at 12 V, 102 mA at 24 V
• Housing: polycarbonate, Ø70 x 50 mm
• Environment: IP65, IP66, -40...+50 °C

The module twist-locks onto a TL70B series base. Unlike the TL70 series, the module has no settings of its own: it is driven by the base input that matches its position in the tower, and flashing is switched on with DIP switches in the base.

CE, UKCA and UL compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

SG-TL70B-W is a Banner TL70B series white 70 mm light module for a modular tower light. When off the segment looks gray, so ambient light does not make it appear lit.

• Color: white, 5000 K, 107 lm
• Mode: steady or flashing 1.5 Hz / 3 Hz
• Supply: 12...30 V DC, 204 mA at 12 V, 102 mA at 24 V
• Housing: polycarbonate, Ø70 x 50 mm
• Environment: IP65, IP66, -40...+50 °C

The module twist-locks onto a TL70B series base. Unlike the TL70 series, the module has no settings of its own: it is driven by the base input that matches its position in the tower, and flashing is switched on with DIP switches in the base.

CE, UKCA and UL compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

SG-TL70B-Y is a Banner TL70B series yellow 70 mm light module for a modular tower light. When off the segment looks gray, so ambient light does not make it appear lit.

• Color: yellow, 590 nm, 55 lm
• Mode: steady or flashing 1.5 Hz / 3 Hz
• Supply: 12...30 V DC, 141 mA at 12 V, 71 mA at 24 V
• Housing: polycarbonate, Ø70 x 50 mm
• Environment: IP65, IP66, -40...+50 °C

The module twist-locks onto a TL70B series base. Unlike the TL70 series, the module has no settings of its own: it is driven by the base input that matches its position in the tower, and flashing is switched on with DIP switches in the base.

CE, UKCA and UL compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

WLS15PXRGB0500DSKQP is a Banner WLS15 Pro series 500 mm RGB strip light controlled over IO-Link. Besides color, flashing and intensity it has level, gauge and segment modes, so the strip can show a fill level or up to 10 separate status zones.

• Light: RGB, 19 color options, each LED individually controllable
• Communication: IO-Link, input response time max. 45 ms
• Supply: 18...30 V DC, typical 0.18 A at 24 V, max. 0.255 A
• Housing: polycarbonate with aluminum frame, polyamide end caps, 500 x 30.6 x 15.5 mm, lighted length 426.4 mm
• Environment: IP66, IP67, -40...+50 °C
• Connection: 150 mm PVC cable with 4-pin M12 male connector

Requires an IO-Link master port. If the master cannot supply the required current, Banner specifies a splitter cable and an external power supply.

CE compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

SG-TL70-AP is a Banner TL70 series 70 mm audible module that plays a user-loaded MP3 or WAV file instead of a fixed tone. It fits on top of a TL70 modular tower light base.

• Audio: MP3 or WAV files, 4 MB flash memory; ships with a 2.5 kHz steady tone
• Trigger: input channel selected with DIP switches; playback repeats while the input is active
• Supply: 12...30 V DC via DC base (330 mA at 12 V), or 100...240 V AC via B-TL70-Z base
• Housing: black polycarbonate, Ø70 x 79.6 mm
• Environment: IP50, -20...+50 °C

Files are loaded over the USB-USBM-1 cable: the module appears on the PC as a USB drive and files are copied onto it. A spoken message or a custom tone can then mark a specific machine state.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

SG-TL70-RGB14 is a Banner TL70 series RGB light module that shows one of 14 colors, chosen with DIP switches. One stocked module can stand in for several single-color segments.

• Colors: 14, including red, green, yellow, blue, white, cyan, magenta and orange
• Mode: steady, flashing or strobe 0.5 / 1.5 / 3 Hz, intensity sweep; high or low intensity
• Supply: 12...30 V DC, high intensity max. 350 mA at 12 V, typical 170 mA at 24 V
• Housing: black polycarbonate, Ø70 x 50 mm
• Environment: IP65, -40...+50 °C

The module twist-locks onto a B-TL70 series base. The black DIP switches set color and mode, the white ones the module's position in the tower (1...6).

CE and UKCA compliant. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

B-TL70PK-QP is the IO-Link base module of the Banner TL70 Pro modular tower light. It carries up to six RGB segments, or five segments plus an audible, and every segment's color, flashing and animation is set over IO-Link.

• Modules: up to 6 SG-TL70P-RGB segments, or 5 segments plus SG-TL70-A, -AL or -AP audible in position 6
• Communication: IO-Link; Basic, Advanced, Run, Level and Gauge modes
• Supply: 18...30 V DC; RGB segment max. 156 mA at 24 V
• Housing: polycarbonate, M30x1.5 thread with nut, 1/2-14 NPT internal, max. 2.25 Nm
• Environment: IP65, UL Type 1, -40...+50 °C
• Connection: 150 mm PVC cable with 4-pin M12 male connector

Light and audible modules are ordered separately and the base needs an IO-Link master port. In Level and Gauge modes the tower shows a process value as a bar of lit segments.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

TLF100P3QP is a Banner TLF100 Pro series 100 mm tower light with three RGB segments in a flat housing that mounts flush on a machine surface. Each segment is switched by its own bimodal PNP or NPN input wire.

• Segments: 3, RGB multicolor, default green/yellow/red from the bottom; e.g. green 7.5 lm, yellow 9.8 lm, red 3.7 lm per segment
• Inputs: bimodal PNP/NPN, one wire per segment, response max. 250 ms; advanced mode adds PWM/PFM (100...5000 Hz), counter and timer inputs
• Supply: 12...30 V DC, typ. 59 mA per segment at 24 V
• Housing: black polycarbonate, 100 x 190 x 42.2 mm, flush mounting; supplied screws for surfaces up to 8 mm
• Environment: IP65, IP69K, UL Type 4X, -40...+50 °C
• Connection: 150 mm PVC cable with 5-pin M12 male connector

Colors, flash patterns, animations and the level, counter and timer modes are set with Banner's free Pro Editor software, which needs the Pro Converter Cable. The cable must not be cleaned with a high-pressure jet.

CE, UKCA and UL marked. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

TLF100P3KQP is a Banner TLF100 Pro series 100 mm tower light with three RGB segments in a flat housing that mounts flush on a machine surface. It is controlled entirely over IO-Link: color, flashing, dimming and animations are set from the controller.

• Segments: 3, RGB multicolor, default green/yellow/red from the bottom; e.g. green 7.5 lm, yellow 9.8 lm, red 3.7 lm per segment
• Communication: IO-Link, response max. 20 ms; basic segment, advanced segment, run, level and gauge modes
• Supply: 18...30 V DC, typ. 59 mA per segment at 24 V, device max. 560 mA
• Housing: black polycarbonate, 100 x 190 x 42.2 mm, flush mounting; supplied screws for surfaces up to 8 mm
• Environment: IP65, IP69K, UL Type 4X, -40...+50 °C
• Connection: 150 mm PVC cable with 4-pin M12 male connector

Needs an IO-Link master port; there are no discrete inputs, so the tower cannot be switched directly from a PLC output. The cable must not be cleaned with a high-pressure jet.

CE, UKCA and UL marked. Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

TL15GYRAQ is a Banner TL15 series kit of four 15 mm in-line segments - green, yellow, red and an audible - that screw together on M12 connectors into an ultra-small tower light. Each segment responds to one pin, so a single 5-pin cable drives all four.

• Segments: green 535 nm (18 lm, pin 4), yellow 590 nm (22 lm, pin 1), red 620 nm (10 lm, pin 2), audible (pin 5)
• Audible: 2.9 kHz, 79 dB at 1 m
• Input: lights bimodal PNP/NPN, audible PNP
• Supply: lights 12 V DC (80 mA) or 24 V DC (40 mA) ±10 %; audible 12...30 V DC
• Environment: lights IP65, IP67, IP68; audible IP60; -40...+50 °C
• Connection: 5-pin M12 male/female on light segments, M12 male on audible

The kit can stand alone or be added in-line to a sensor or an existing tower light; the segments are packed separately and assembled on site.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

LC15T-127AL2RGQP is a Banner LC15T series capacitive touch switch that sits in an M12 line between the supply and a DC device. A single touch switches the output on (green) or off (red).

• Function: on/off, red = off, green = on
• Pass-through current: max. 4 A
• Supply: 12...30 V DC, 11 mA typical at 24 V
• Housing: polycarbonate, polyamide end caps, Ø15 x 126.9 mm, slots for M4 screws
• Environment: IP66, IP67, IK06, -40...+60 °C
• Connection: 150 mm PVC cables with 4-pin M12 male (input) and female (output)

Switches any DC device that takes constant power on pins 1 and 3, such as a Banner LED work light, without a separate switch box.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

S22AMTSGRHQP is a Banner S22 Pro series 22 mm touch button with a momentary output. With power applied it glows green; a touch switches the output and turns it red.

• Colors: green 527 nm, red 625 nm (touched)
• Output: bipolar, normally open, momentary, max. 150 mA; input response 20 ms, output 300 ms
• Supply: 10...30 V DC, 45 mA at 24 V
• Housing: polycarbonate base, dome and nut, M22x1.5 thread, max. 2.25 Nm
• Environment: IP66, IP67, IP69K, -40...+50 °C
• Connection: 150 mm PVC cable with 5-pin M12 male connector

Fits a standard 22 mm push-button hole in a panel and is configurable with Pro Editor.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

S22ALTSGRHQ is a Banner S22 Pro series 22 mm touch button with a latching output. With power applied it glows green; a touch switches the output and turns it red.

• Colors: green 527 nm, red 625 nm (touched)
• Output: bipolar, normally open, latching, max. 150 mA; input response 20 ms, output 300 ms
• Supply: 10...30 V DC, 45 mA at 24 V
• Housing: polycarbonate base, dome and nut, M22x1.5 thread, max. 2.25 Nm
• Environment: IP66, IP67, IP69K, -40...+50 °C
• Connection: integral 5-pin M12 male connector

Fits a standard 22 mm push-button hole in a panel and is configurable with Pro Editor.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

K30PAF100AMGRY3Q is a Banner K30 Pro series 30 mm touchless button: an infrared adjustable-field sensor behind an RGB dome that switches when a hand or object comes within the taught distance, up to 100 mm, and ignores what lies beyond it.

• Sensing: adjustable field up to 100 mm, infrared 940 nm; object, background or window teach
• Output: bipolar, normally open, momentary, max. 150 mA, response 120 ms
• Indicator: green (5.8 lm), yellow (7.9 lm), red (3.2 lm) by default; 14 colors via Pro Editor
• Supply: 10...30 V DC, 30 mA typical at 24 V
• Housing: polycarbonate base, dome and nut, M22x1.5 thread
• Environment: IP65, -20...+50 °C
• Connection: integral 5-pin M12 male connector

The switch point is taught over the remote input wire or the Pro Converter Cable button; the dome shows signal strength in green, yellow or red during teach. Allow 5 minutes warm-up for best repeatability.

Vibration per MIL-STD-202F method 201A, shock per method 213B (75 G operating).

K30PTALGRY3Q is a Banner K30 Pro series 30 mm touch button with an RGB indicator and a latching output. Two inputs select green, yellow or red; colors, animation, output logic and touch sensitivity are changed with Pro Editor software.

• Colors (default): green 522 nm (7.7 lm), yellow 576 nm (7.8 lm), red 620 nm (3.1 lm); up to 14 colors via Pro Editor
• Output: bipolar, normally open, latching, max. 100 mA; input response 40 ms, output 300 ms
• Supply: 12...30 V DC, 80 mA at 12 V, 40 mA at 24 V
• Housing: polycarbonate base, dome and nut, M22x1.5 thread, Ø30 x 54.5 mm
• Environment: IP67, IP69K, -40...+50 °C
• Connection: integral 5-pin M12 male connector

Programming needs the Pro Converter Cable and Pro Editor. The M22 base fits a standard 22 mm push-button hole.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

K50PTVKQ is a Banner K50 Pro series 50 mm touch button with an RGB indicator, vibration feedback on touch and IO-Link control. The touch state is reported to the controller, which also sets color, animation and output logic.

• Indicator: 14 default colors plus custom colors
• Vibration feedback: steady or pattern, max. 3 s per touch, 500 000 cycles
• Communication: IO-Link COM2 (38.4 kbps), process data 2 bytes in, 10 bytes out
• Function: NO or NC, momentary or latching, on/off delay 0...60 000 ms
• Supply: 18...30 V DC, 93 mA typical at 24 V
• Housing: polycarbonate, M30x1.5 thread, Ø50 x 66 mm; IP67, IP69K, -40...+50 °C
• Connection: integral 4-pin M12 male connector

Needs an IO-Link master port. The vibration gives the operator a confirmation that can be felt through gloves.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

K50PCLRGB7KAQP is a Banner K50 Pro series compact 50 mm RGB indicator with a built-in audible, controlled entirely over IO-Link. Color, flashing, dimming, animation and the audible tone are set from the controller.

• Indicator: RGB multicolor, e.g. green 8.9 lm, yellow 11.6 lm, red 3.9 lm
• Audible: 14 tones, 2.9 kHz continuous tone at 83 / 88 / 92 dB (1 m)
• Communication: IO-Link, input response 250 ms
• Supply: 18...30 V DC, 83 mA at 24 V, max. 145 mA
• Housing: polycarbonate base, dome and nut, M30x1.5 thread, Ø50 x 69.6 mm
• Environment: IP67, IP69K, UL Type 4X, -40...+50 °C
• Connection: 150 mm PVC cable with 4-pin M12 male connector

Needs an IO-Link master port; there are no discrete inputs, so it cannot be driven directly from a PLC output.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (30 G, 11 ms).

WC-K50C is a Banner silicone cover that protects K50 compact indicators and touch buttons in washdown areas.

• Fits: Banner K50 compact indicators and touch buttons
• Material: FDA-grade silicone
• Protection rating: IP67 and IP69K

SMB30SC is a Banner swivel bracket for sensors with a 30 mm housing. Once the orientation is set, the swivel is locked with the included screw.

• Sensor hole: Ø30.0 mm
• Mounting: Ø7.0 mm holes on a Ø50.8 mm circle
• Material: black reinforced thermoplastic polyester
• Included: stainless steel mounting and swivel locking hardware

TL15A5Q is a Banner TL15 series 15 mm audible segment that fits in an M12 line or on top of a TL15 in-line tower light. It sounds when pin 5 is driven with a PNP signal.

• Audible: 2.9 kHz, 79 dB at 1 m; small yellow LED lights while sounding
• Input: PNP, active on pin 5
• Supply: 12...30 V DC, 55 mA at 12 V, 30 mA at 24 V
• Housing: nylon, Ø15 x 58 mm, nickel-plated brass coupling
• Environment: IP60, UL Type 1, -40...+50 °C
• Connection: integral 5-pin M12 male connector

The audible segment has only a male connector, so it is always the last element of a TL15 stack.

Vibration per IEC 60068-2-6, shock per IEC 60068-2-27 (15 G, 11 ms).

S15LPRGB7Q is a Banner S15L Pro series RGB status indicator with four discrete inputs that screws into an M12 cable run. Three inputs select seven colors in combination, and the fourth input (gray wire) switches on 1 Hz flashing.

• Colors: 7 by default (red, yellow, green, cyan, blue, magenta, white), 14 selectable in total
• Inputs: 4, PNP/NPN, 12...30 V DC, response time up to 250 ms
• Configuration: Banner Pro Editor - colors, intensity, flash pattern, animations
• Supply: 12...30 V DC, up to 60 mA at 12 V DC, typically 35 mA at 24 V DC
• Housing: Ø15 × 58 mm, nickel-plated brass coupling, diffuse white PVC
• Environment: IP65, IP67, IP68, -40...+45 °C
• Connection: integral 5-pin M12 male and female

The indicator is driven directly by PLC or sensor outputs and shows machine status where a separate stack light would not fit. Without any setup it works from the factory color table. Changing the settings in Pro Editor requires a Banner Pro Converter cable, ordered separately.

Meets CE and UKCA requirements, enclosure rating UL Type 1. Vibration and shock resistance tested to IEC 60068-2-6 and IEC 60068-2-27.

S15LPSQ is a Banner S15L Pro series RGB status indicator controlled over a Modbus RTU network that screws into a cable run with 4-pin M12 connectors. Color, intensity, flash pattern and speed are set by writing Modbus registers, so no separate wire is needed per color.

• Colors: 14 selectable, with flash, two-color flash and color sweep
• Communication: Modbus RTU, RS-485 (pins 2 and 4)
• Supply: 12...30 V DC, up to 60 mA at 12 V DC, typically 35 mA at 24 V DC
• Housing: Ø15 × 58 mm, nickel-plated brass coupling, diffuse white PVC
• Environment: IP65, IP67, IP68, -40...+45 °C
• Connection: integral 4-pin M12 male and female

The indicator is used on machines where the PLC already communicates over Modbus RTU, and it connects anywhere on the RS-485 line. It needs a Modbus RTU master, such as a PLC, to operate. Normal-mode settings are not stored in the indicator, so the controller must write them again after a power loss.

Meets CE and UKCA requirements, enclosure rating UL Type 1. Vibration and shock resistance tested to IEC 60068-2-6 and IEC 60068-2-27.