CMVT-QR20-IOLX3-H1141/3GD is a condition monitoring vibration and temperature sensor measuring acceleration and velocity over three axes plus the housing temperature. It is the ATEX version of the CMVT-QR20 for zones 2 and 22 - the measuring side is unchanged, but the device carries an Ex marking and a narrower permitted ambient range.

• Measuring range: acceleration 16 g RMS (6.6 kHz sampling), velocity 0...320 mm/s RMS @ 78 Hz, temperature -40...+85°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: velocity linearity deviation ≤ ±1 % @ 78 Hz, acceleration ≤ ±3 % @ 78 Hz; repeatability ≤ ±5 % @ 78 Hz
• Outputs: pin 4 - IO-Link or SIO, pin 2 - SIO; two PNP/NPN switching outputs in SIO mode; IO-Link COM 3 (230.4 kBaud)
• Supply: 18...30 VDC (IO-Link), 10...30 VDC (SIO), consumption < 50 mA
• Protection: against wire break and reverse polarity
• Housing: rectangular QR20, Ultem plastic, 71.6 x 62.6 x 20 mm
• Environment: IP68/IP69K, pollution degree 3, shock 200 g (4 ms), vibration 20 g; permitted ambient in the ATEX zone -30...+70°C
• Connection: M12 x 1 male connector, 4-pin

Device marking: Ex II 3 G Ex ec IIC T4 Gc / II 3 D Ex tc. The plug connection must not be disconnected under voltage, and the sensor must be protected against mechanical damage.

Over IO-Link the output quantity is selectable - acceleration or velocity, RMS or peak-to-peak - and the switching thresholds are set there. Thresholds can be parameterised to the ISO 10816-3 machine classes or defined freely. A green LED shows the supply and, when flashing, active IO-Link communication; two yellow LEDs show an exceeded threshold.

UL registration number E351232. MTTF 548 years to SN 29500 (Ed. 99) at 40°C. Shock tested to EN 60068-2-27, vibration to EN 60068-2-6, temperature cycling to EN 60068-2-14 (20 cycles).

CMVT-M8TA1X-LI2IOL-H1141 is a stainless steel vibration and temperature sensor with an M8 screw-in thread, measuring over one axis at a 23.6 kHz sampling rate. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: acceleration 10 g RMS / 14 g peak, velocity 0...128 mm/s RMS @ 159 Hz, temperature -40...+80°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: ≤ ±0.5 % @ 159 Hz; temperature linearity deviation ≤ 10 %
• Outputs: pin 4 - IO-Link or SIO, pin 2 - 4...20 mA or SIO; IO-Link COM 2 (38.4 kBaud)
• Supply: 18...30 VDC, consumption < 120 mA in IO-Link mode
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms), vibration 20 g
• Connection: M12 x 1 connector, 4-pin

Frequency ranges and switching thresholds are configurable over IO-Link, so only the band in which a given machine's fault appears has to be watched. The 4...20 mA output on pin 2 carries the same quantity in analogue form, so the sensor connects to a controller with no IO-Link master.

MTTF 164 years to SN 29500 (Ed. 99). Shock tested to EN 60068-2-27, vibration to EN 60068-2-6.

CMVT-M8TE1X-LI2IOL-H1141 is a stainless steel vibration and temperature sensor with an M8 screw-in thread and a 64 kHz sampling rate. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: acceleration 33.9 g RMS / 48 g peak (10 Hz...10 kHz), velocity 0...256 mm/s RMS @ 159 Hz, temperature -40...+80°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: ≤ ±0.5 % @ 159 Hz; temperature linearity deviation ≤ 10 %
• Outputs: pin 4 - IO-Link or SIO, pin 2 - 4...20 mA or SIO; IO-Link COM 3 (230.4 kBaud)
• Supply: 18...30 VDC, consumption < 120 mA in IO-Link mode
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms)
• Connection: M12 x 1 connector, 4-pin

Besides the aggregated RMS values the sensor outputs a bearing condition indicator and transfers the raw signal over IO-Link BLOB at up to 64 kHz with a low-pass filter at 12 kHz. FFT analysis can therefore be done off the sensor - on the controller or a server. Frequency ranges and thresholds are configurable over IO-Link.

MTTF 112 years to SN 29500 (Ed. 99) at 40°C. Shock tested to EN 60068-2-27.

CMVT-M8TA1X-LI220-H1141 is a stainless steel vibration sensor with an M8 screw-in thread that measures the velocity RMS value over one axis and outputs it as a 4...20 mA signal, where 20 mA corresponds to 20 mm/s RMS. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: velocity 0...20 mm/s RMS, one axis, 23.6 kHz sampling
• Accuracy: ≤ ±0.5 % @ 159 Hz
• Outputs: 4...20 mA, load resistance ≤ 0.5 kΩ
• Supply: 18...30 VDC, consumption < 100 mA
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms), vibration 20 g
• Connection: M12 x 1 connector, 4-pin

There is no IO-Link and nothing to configure - the sensor wires straight into a controller's analogue input, and the measuring span is fixed by the model chosen.

MTTF 164 years to SN 29500 (Ed. 99). Shock tested to EN 60068-2-27, vibration to EN 60068-2-6.

CMVT-M8TA1X-LI225-H1141 is a stainless steel vibration sensor with an M8 screw-in thread that measures the velocity RMS value over one axis and outputs it as a 4...20 mA signal, where 20 mA corresponds to 25 mm/s RMS. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: velocity 0...25 mm/s RMS, one axis, 23.6 kHz sampling
• Accuracy: ≤ ±0.5 % @ 159 Hz
• Outputs: 4...20 mA, load resistance ≤ 0.5 kΩ
• Supply: 18...30 VDC, consumption < 100 mA
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms), vibration 20 g
• Connection: M12 x 1 connector, 4-pin

There is no IO-Link and nothing to configure - the sensor wires straight into a controller's analogue input, and the measuring span is fixed by the model chosen.

MTTF 164 years to SN 29500 (Ed. 99). Shock tested to EN 60068-2-27, vibration to EN 60068-2-6.

CMTH-M12-IOL6X2-H1141 is a capacitive humidity and temperature sensor for condition monitoring. It is intended for machine parts where temperature or humidity affects machine availability or process quality, and suits both indoor and outdoor use.

• Accuracy: temperature ±0.8°C; humidity ±5 % RH (10...90 % RH), ±7 % RH (0...10 % and 90...100 % RH). When installed in metal, in an environment with convection
• Measuring range: temperature -40...+100°C, humidity 0...100 % RH, resolution 0.1 K and 0.1 % RH; humidity response time t63 6 s
• Outputs: output 1 - switching or IO-Link, output 2 - switching; IO-Link v1.1 COM 3, Class A, Smart Sensor Profile 4
• Supply: 18...30 VDC, DC 4-wire, consumption < 50 mA, rated current ≤ 150 mA
• Protection: against short circuit, wire break and reverse polarity
• Housing: chrome-plated CuZn metal, M12 x 1 thread, nut torque up to 10 Nm
• Environment: IP67, operating temperature -40...+100°C
• Connection: M12 x 1 connector, 4-pin, cable up to 20 m

Over IO-Link a temperature offset is configurable and switching thresholds or windows can be set for temperature and humidity. The sensor calculates the dew point, builds temperature and humidity histograms and counts operating hours and threshold transitions. A green LED shows the supply.

Meets CE and UL requirements. EMC to EN 61326-1, shock to IEC 60068-2-27 (50 g, 6 ms), vibration to IEC 60068-2-6 (10...150 Hz, 20 g). MTTF 610 years.

CMTH-M12-IOL6X2-H1141/3GD is a capacitive humidity and temperature sensor for condition monitoring in the ATEX version for zones 2 and 22. It is intended for machine parts where temperature or humidity affects machine availability or process quality, and suits both indoor and outdoor use.

• Accuracy: temperature ±0.8°C; humidity ±5 % RH (10...90 % RH), ±7 % RH (0...10 % and 90...100 % RH). When installed in metal, in an environment with convection
• Measuring range: temperature -40...+100°C, humidity 0...100 % RH, resolution 0.1 K and 0.1 % RH; humidity response time t63 6 s
• Outputs: output 1 - switching or IO-Link, output 2 - switching; IO-Link v1.1 COM 3, Class A, Smart Sensor Profile 4
• Supply: 18...30 VDC, DC 4-wire, consumption < 50 mA, rated current ≤ 150 mA
• Protection: against short circuit, wire break and reverse polarity
• Housing: chrome-plated CuZn metal, M12 x 1 thread, nut torque up to 10 Nm
• Environment: IP67, operating temperature -40...+100°C; ATEX category II 3 G (Ex zone 2) and II 3 D (Ex zone 22)
• Connection: M12 x 1 connector, 4-pin, cable up to 20 m

Over IO-Link a temperature offset is configurable and switching thresholds or windows can be set for temperature and humidity. The sensor calculates the dew point, builds temperature and humidity histograms and counts operating hours and threshold transitions. A green LED shows the supply.

Meets CE and UL requirements. EMC to EN 61326-1, shock to IEC 60068-2-27 (50 g, 6 ms), vibration to IEC 60068-2-6 (10...150 Hz, 20 g). MTTF 610 years.

CMTH-M12E-IOL6X2-H1141 is a capacitive humidity and temperature sensor for condition monitoring with an integrated heating function that stabilises the measurement. It is intended for machine parts where temperature or humidity affects machine availability or process quality, and suits both indoor and outdoor use.

• Accuracy: temperature ±0.5°C; humidity ±3.5 % RH (10...90 % RH), ±5 % RH (0...10 % and 90...100 % RH). When installed in metal, in an environment with convection
• Measuring range: temperature -40...+100°C, humidity 0...100 % RH, resolution 0.1 K and 0.1 % RH
• Outputs: output 1 - switching or IO-Link, output 2 - switching; IO-Link v1.1 COM 3, Class A, Smart Sensor Profile 4
• Supply: 18...30 VDC, DC 4-wire, consumption < 50 mA, rated current ≤ 150 mA
• Protection: against short circuit, wire break and reverse polarity
• Housing: chrome-plated CuZn metal, M12 x 1 thread, nut torque up to 10 Nm
• Environment: IP67, operating temperature -40...+100°C
• Connection: M12 x 1 connector, 4-pin, cable up to 20 m

Over IO-Link a temperature offset is configurable and switching thresholds or windows can be set for temperature and humidity. The sensor calculates the dew point, builds temperature and humidity histograms and counts operating hours and threshold transitions. A green LED shows the supply.

Meets CE and UL requirements. EMC to EN 61326-1, shock to IEC 60068-2-27 (50 g, 6 ms), vibration to IEC 60068-2-6 (10...150 Hz, 20 g). MTTF 610 years.

CMMT-QR20-IOL6X3-H1141 is a magnetic field sensor for condition monitoring that measures the field over three axes, calculates the sum vector and reads temperature as well. It is intended for positions where a change in the magnetic field reports on machine condition - the weakening of a permanent magnet, or the influence of a stray field.

• Measuring range: magnetic field -2500...+2500 µT, resolution 1 µT; temperature -25...+70°C, resolution 0.1 K
• Response time: at least 8 s
• Outputs: output 1 - PNP/NPN or IO-Link, output 2 - PNP/NPN; IO-Link COM 3 (230.4 kBaud), Smart Sensor Profile
• Supply: 18...30 VDC, no-load current 80 mA, rated current ≤ 250 mA
• Protection: against short circuit (cyclic), wire break and reverse polarity
• Housing: rectangular QR20, Ultem plastic, 71.6 x 62.6 x 20 mm
• Environment: IP68/IP69K, pollution degree 3, operating temperature -25...+70°C
• Connection: M12 x 1 male connector, 4-pin

Over IO-Link an offset and a limit value can be set per axis and assigned to a specific switching output, so which direction is changing can be separated out. A green LED shows the supply, two yellow LEDs the output states.

EMC to EN 61326-1.

MAGKIT-M8T is the magnetic mount for the CMVT-M8T family of vibration sensors. The sensor screws into the magnet's female thread, and the magnet is placed on the machine surface without drilling or cutting a thread in the equipment itself.

• Fits: CMVT-M8T family sensors with an M8 screw-in thread
• Thread: M8 x 12 mm, female
• Material: stainless steel V4A
• Holding force: 342 N at 28°C

The mount is intended for flexible, relocatable mounting. Permanent and operationally secure fixing depends on the conditions at the application and must be evaluated by the user.

MAGKIT-M5 is the magnetic mounting kit for CMVT-QR20 rectangular-housing sensors. The sensor is screwed to two magnets with the supplied M5 screws, and the magnets hold it on the machine surface without drilling a hole in the equipment.

• Fits: CMVT-QR20 and CMMT-QR20 family sensors
• Supplied: 2 mounting magnets, 2 washers, 2 M5 x 12 screws
• Dimensions: magnet Ø 32 x 7 mm, M5 female thread

Permanent and operationally secure fixing depends on the conditions at the application and must be evaluated by the user.

RKH4.4-10/TFE is a TURCK connection cable with a straight M12 female connector (4-pin) on one end and open cores on the other.

• Connector: M12 x 1 female, straight, 4-pin
• Cable: 10 m, PVC, grey, Ø 4.5 mm, 4 x 0.34 mm², core colours BN, WH, BU, BK
• Ratings: 4 A, 250 V
• Housing: grey PP, stainless steel (V4A) coupling nut, FPM/FKM seal
• Environment: IP65, IP67, IP68, IP69 (only when screwed in); -25...+80°C fixed, 0...+80°C mobile

Designed for food and beverage areas: grey PVC jacket (RAL 7040) resistant to acids, alkalis, oils and chemicals, flame retardant per DIN EN 60332, stainless steel coupling nut. RoHS and REACH compliant. Approvals: GOST, Ecolab.

RKC8T-2-RSC8T/TXL is a TURCK extension cable with a straight M12 female connector on one end and a straight M12 male connector on the other (8-pin).

• Connectors: M12 x 1 female, straight, A-coded / M12 x 1 male, straight, A-coded; 8-pin, gold-plated brass (CuZn) contacts
• Cable: 2 m, PUR, black, Ø 5.8 mm, 8 x 0.25 mm², core colours BN, WH, BU, BK, GY, PK, VT, OG
• Ratings: 2 A, 30 V, more than 100 mating cycles
• Housing: TPU, nickel-plated brass coupling nuts, FPM/FKM seal
• Environment: IP67, IP69K (only when screwed in); -50...+80°C fixed, -25...+80°C mobile, -25...+60°C in a drag chain
• Drag chain: at least 5 million bending cycles, up to 3.3 m/s and 5 m/s², bending radius ≥10 x Ø, torsion ±180°/m

The PUR jacket resists chemicals, UV radiation, oils, welding sparks and abrasion, is flame retardant (FT2 per UL 1581, IEC 60332-2-2) and free from halogen, silicone, PVC and LABS. Approval: cULus.