BWA-QM30-FMSS is a Banner magnetic bracket for attaching a QM30 vibration sensor to a flat steel surface without drilling. The sensor is screwed to the bracket and the NdFeB magnet holds the assembly on the machine.

• Fits: Banner QM30 vibration sensors, aluminium and stainless steel versions
• Surface: flat
• Material: 410 stainless steel body with NdFeB magnet insert
• Size: 30 x 30 mm
• Included: bracket and two sets of 304 stainless steel screws

SMBDX80DIN is a Banner bracket for mounting a Sure Cross DX80 device on a 35 mm DIN rail inside a cabinet.

• Fits: Sure Cross DX80 devices
• Mounting: 35 mm DIN rail
• Material: black reinforced thermoplastic
• Included: mounting hardware, 1 bracket

QM30VT3-SS-MQP is a Banner QM30VT3 3-axis vibration and temperature sensor for condition monitoring of motors, pumps, fans and other rotating machines. It works as a Modbus RTU server on RS-485 and delivers pre-processed values such as RMS velocity, high-frequency RMS acceleration and peak velocity per axis.

• Accuracy: vibration ±5 % at 25 °C; temperature ±3 °C
• Measuring range: vibration ±16 g, 0...65.5 mm/s RMS, 6 Hz...5.3 kHz; temperature -40...+105 °C, resolution 1 °C
• Output: RS-485, Modbus RTU, 9.6/19.2/38.4 kbaud
• Supply: 10...30 V DC, 9 mA at 30 V DC
• Housing: stainless steel 316L, 30 mm; mounting by M4 screw, epoxy, thermal tape or magnet
• Environment: IP69K, -40...+105 °C
• Connection: 150 mm cable with M12 5-pin male connector

High-frequency enveloping mode is available for bearing fault diagnostics, and the FMax setting (325...5300 Hz) trades bandwidth against frequency resolution. Configuration and firmware updates are done with the SNAP SIGNAL software and the BWA-UCT-900 USB adapter cable.

Shock per MIL-STD-202G, method 213B (100 g). FCC Part 15 Class B, ICES-003(B); CE and UKCA declaration of conformity.

QM30VT3-MQP is a Banner QM30VT3 3-axis vibration and temperature sensor for condition monitoring of motors, pumps, fans and other rotating machines. It works as a Modbus RTU server on RS-485 and delivers pre-processed values such as RMS velocity, high-frequency RMS acceleration and peak velocity per axis.

• Accuracy: vibration ±5 % at 25 °C; temperature ±3 °C
• Measuring range: vibration ±16 g, 0...65.5 mm/s RMS, 6 Hz...5.3 kHz; temperature -40...+105 °C, resolution 1 °C
• Output: RS-485, Modbus RTU, 9.6/19.2/38.4 kbaud
• Supply: 10...30 V DC, 9 mA at 30 V DC
• Housing: aluminium, 30 mm; mounting by M4 screw, epoxy, thermal tape or magnet
• Environment: IP67, -40...+105 °C
• Connection: 150 mm cable with M12 5-pin male connector

High-frequency enveloping mode is available for bearing fault diagnostics, and the FMax setting (325...5300 Hz) trades bandwidth against frequency resolution. Configuration and firmware updates are done with the SNAP SIGNAL software and the BWA-UCT-900 USB adapter cable.

Shock per MIL-STD-202G, method 213B (100 g). FCC Part 15 Class B, ICES-003(B); CE and UKCA declaration of conformity.

CMVT-QR20-IOLX3-H1141 is a condition monitoring vibration and temperature sensor measuring acceleration and velocity over three axes plus the housing temperature. It is intended for rotating machine parts where rising vibration indicates bearing wear, imbalance or shaft misalignment, so the deviation is caught before a failure.

• Measuring range: acceleration 16 g RMS (6.6 kHz sampling), velocity 0...320 mm/s RMS @ 78 Hz, temperature -40...+85°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: velocity linearity deviation ≤ ±1 % @ 78 Hz, acceleration ≤ ±3 % @ 78 Hz; repeatability ≤ ±5 % @ 78 Hz
• Outputs: pin 4 - IO-Link or SIO, pin 2 - SIO; two PNP/NPN switching outputs in SIO mode; IO-Link COM 3 (230.4 kBaud)
• Supply: 18...30 VDC (IO-Link), 10...30 VDC (SIO), consumption < 50 mA
• Protection: against wire break and reverse polarity
• Housing: rectangular QR20, Ultem plastic, 71.6 x 62.6 x 20 mm
• Environment: IP68/IP69K, pollution degree 3, shock 200 g (4 ms), vibration 20 g
• Connection: M12 x 1 male connector, 4-pin

Over IO-Link the output quantity is selectable - acceleration or velocity, RMS or peak-to-peak - and the switching thresholds are set there. Thresholds can be parameterised to the ISO 10816-3 machine classes or defined freely. A green LED shows the supply and, when flashing, active IO-Link communication; two yellow LEDs show an exceeded threshold.

UL registration number E351232. MTTF 548 years to SN 29500 (Ed. 99) at 40°C. Shock tested to EN 60068-2-27, vibration to EN 60068-2-6, temperature cycling to EN 60068-2-14 (20 cycles).

CMVT-QR20-IOLX3-H1141/3GD is a condition monitoring vibration and temperature sensor measuring acceleration and velocity over three axes plus the housing temperature. It is the ATEX version of the CMVT-QR20 for zones 2 and 22 - the measuring side is unchanged, but the device carries an Ex marking and a narrower permitted ambient range.

• Measuring range: acceleration 16 g RMS (6.6 kHz sampling), velocity 0...320 mm/s RMS @ 78 Hz, temperature -40...+85°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: velocity linearity deviation ≤ ±1 % @ 78 Hz, acceleration ≤ ±3 % @ 78 Hz; repeatability ≤ ±5 % @ 78 Hz
• Outputs: pin 4 - IO-Link or SIO, pin 2 - SIO; two PNP/NPN switching outputs in SIO mode; IO-Link COM 3 (230.4 kBaud)
• Supply: 18...30 VDC (IO-Link), 10...30 VDC (SIO), consumption < 50 mA
• Protection: against wire break and reverse polarity
• Housing: rectangular QR20, Ultem plastic, 71.6 x 62.6 x 20 mm
• Environment: IP68/IP69K, pollution degree 3, shock 200 g (4 ms), vibration 20 g; permitted ambient in the ATEX zone -30...+70°C
• Connection: M12 x 1 male connector, 4-pin

Device marking: Ex II 3 G Ex ec IIC T4 Gc / II 3 D Ex tc. The plug connection must not be disconnected under voltage, and the sensor must be protected against mechanical damage.

Over IO-Link the output quantity is selectable - acceleration or velocity, RMS or peak-to-peak - and the switching thresholds are set there. Thresholds can be parameterised to the ISO 10816-3 machine classes or defined freely. A green LED shows the supply and, when flashing, active IO-Link communication; two yellow LEDs show an exceeded threshold.

UL registration number E351232. MTTF 548 years to SN 29500 (Ed. 99) at 40°C. Shock tested to EN 60068-2-27, vibration to EN 60068-2-6, temperature cycling to EN 60068-2-14 (20 cycles).

CMVT-M8TA1X-LI2IOL-H1141 is a stainless steel vibration and temperature sensor with an M8 screw-in thread, measuring over one axis at a 23.6 kHz sampling rate. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: acceleration 10 g RMS / 14 g peak, velocity 0...128 mm/s RMS @ 159 Hz, temperature -40...+80°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: ≤ ±0.5 % @ 159 Hz; temperature linearity deviation ≤ 10 %
• Outputs: pin 4 - IO-Link or SIO, pin 2 - 4...20 mA or SIO; IO-Link COM 2 (38.4 kBaud)
• Supply: 18...30 VDC, consumption < 120 mA in IO-Link mode
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms), vibration 20 g
• Connection: M12 x 1 connector, 4-pin

Frequency ranges and switching thresholds are configurable over IO-Link, so only the band in which a given machine's fault appears has to be watched. The 4...20 mA output on pin 2 carries the same quantity in analogue form, so the sensor connects to a controller with no IO-Link master.

MTTF 164 years to SN 29500 (Ed. 99). Shock tested to EN 60068-2-27, vibration to EN 60068-2-6.

CMVT-M8TE1X-LI2IOL-H1141 is a stainless steel vibration and temperature sensor with an M8 screw-in thread and a 64 kHz sampling rate. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: acceleration 33.9 g RMS / 48 g peak (10 Hz...10 kHz), velocity 0...256 mm/s RMS @ 159 Hz, temperature -40...+80°C; resolution 0.01 g and 0.01 mm/s
• Accuracy: ≤ ±0.5 % @ 159 Hz; temperature linearity deviation ≤ 10 %
• Outputs: pin 4 - IO-Link or SIO, pin 2 - 4...20 mA or SIO; IO-Link COM 3 (230.4 kBaud)
• Supply: 18...30 VDC, consumption < 120 mA in IO-Link mode
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms)
• Connection: M12 x 1 connector, 4-pin

Besides the aggregated RMS values the sensor outputs a bearing condition indicator and transfers the raw signal over IO-Link BLOB at up to 64 kHz with a low-pass filter at 12 kHz. FFT analysis can therefore be done off the sensor - on the controller or a server. Frequency ranges and thresholds are configurable over IO-Link.

MTTF 112 years to SN 29500 (Ed. 99) at 40°C. Shock tested to EN 60068-2-27.

CMVT-M8TA1X-LI220-H1141 is a stainless steel vibration sensor with an M8 screw-in thread that measures the velocity RMS value over one axis and outputs it as a 4...20 mA signal, where 20 mA corresponds to 20 mm/s RMS. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: velocity 0...20 mm/s RMS, one axis, 23.6 kHz sampling
• Accuracy: ≤ ±0.5 % @ 159 Hz
• Outputs: 4...20 mA, load resistance ≤ 0.5 kΩ
• Supply: 18...30 VDC, consumption < 100 mA
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms), vibration 20 g
• Connection: M12 x 1 connector, 4-pin

There is no IO-Link and nothing to configure - the sensor wires straight into a controller's analogue input, and the measuring span is fixed by the model chosen.

MTTF 164 years to SN 29500 (Ed. 99). Shock tested to EN 60068-2-27, vibration to EN 60068-2-6.

CMVT-M8TA1X-LI225-H1141 is a stainless steel vibration sensor with an M8 screw-in thread that measures the velocity RMS value over one axis and outputs it as a 4...20 mA signal, where 20 mA corresponds to 25 mm/s RMS. It is intended for rotating machine parts where rising vibration indicates bearing wear or imbalance; the sensor screws into the bearing housing along the axis where the vibration is expected.

• Measuring range: velocity 0...25 mm/s RMS, one axis, 23.6 kHz sampling
• Accuracy: ≤ ±0.5 % @ 159 Hz
• Outputs: 4...20 mA, load resistance ≤ 0.5 kΩ
• Supply: 18...30 VDC, consumption < 100 mA
• Housing: stainless steel, M8 screw-in thread, 72.5 x 23.8 mm
• Environment: IP66/IP67, operating temperature -40...+80°C, shock 60 g (6 ms), vibration 20 g
• Connection: M12 x 1 connector, 4-pin

There is no IO-Link and nothing to configure - the sensor wires straight into a controller's analogue input, and the measuring span is fixed by the model chosen.

MTTF 164 years to SN 29500 (Ed. 99). Shock tested to EN 60068-2-27, vibration to EN 60068-2-6.

MAGKIT-M8T is the magnetic mount for the CMVT-M8T family of vibration sensors. The sensor screws into the magnet's female thread, and the magnet is placed on the machine surface without drilling or cutting a thread in the equipment itself.

• Fits: CMVT-M8T family sensors with an M8 screw-in thread
• Thread: M8 x 12 mm, female
• Material: stainless steel V4A
• Holding force: 342 N at 28°C

The mount is intended for flexible, relocatable mounting. Permanent and operationally secure fixing depends on the conditions at the application and must be evaluated by the user.

MAGKIT-M5 is the magnetic mounting kit for CMVT-QR20 rectangular-housing sensors. The sensor is screwed to two magnets with the supplied M5 screws, and the magnets hold it on the machine surface without drilling a hole in the equipment.

• Fits: CMVT-QR20 and CMMT-QR20 family sensors
• Supplied: 2 mounting magnets, 2 washers, 2 M5 x 12 screws
• Dimensions: magnet Ø 32 x 7 mm, M5 female thread

Permanent and operationally secure fixing depends on the conditions at the application and must be evaluated by the user.